Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    100-Gigabit Ethernet PIC with CFP2 (PTX Series)

    Software Release

    • PTX5000: Junos OS Release 14.1 and later

    Hardware Features

    • Four 100-Gigabit Ethernet ports

    • Model number: P2-100GE-CFP2

    • Name in the CLI: 4x100GE CFP2

    • Power requirements: 1.66A@ –48 V (90W)

    • Large maximum transmission units (MTUs): up to 9500 bytes

    Software Features

    Table 1 shows the first supported release for each software feature.

    Table 1: Software Features Supported

    Software Feature

    PTX5000 First Supported Junos OS Release

    Flexible-ethernet-services encapsulation

    14.1

    Flexible VLAN tagging

    14.1

    IFINFO / IFMON

    14.1

    IEEE 802.1 ag OAM

    14.1

    IEEE 802.3 ah OAM

    14.1

    IEEE 802.3ad link aggregation

    14.1

    Interrupt-driven link-down detection for MPLS FRR

    14.1

    MAC accounting per logical interface for source addresses

    14.1

    MAC filter per port for destination addresses and source addresses

    14.1

    MAC filter per logical interface for source addresses

    14.1

    SNMP

    14.1

    Up to 4000 logical interfaces share across all ports on a single PFE

    14.1

    Cables and Connectors

    The following transceivers are supported on this PIC:

    • CFP2-100G-LR4-D—Supports 100GBASE-LR4

      • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

      • Connector: LC

    • CFP2-100G-SR10-D—Supports 100GBASE-SR10

      • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

      • Connector: 24-fiber MPO

    • CFP2-100GBASE-LR4—Supports 100GBASE-LR4

      • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

      • Connector: LC

    • CFP2-100GBASE-SR10—Supports 100GBASE-SR10

      • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

      • Connector: 24-fiber MPO

    Note: The dual-rate transceiver (CFP2-100G-LR4-D) cannot be configured to use OTN framing when used in this PIC. The 100-Gigabit Ethernet OTN PIC with CFP2 (P2-100GE-OTN) supports OTN framing.

    LEDs

    The STATUS LED is located to the left of the ONLINE/OFFLINE button. One LED is located next to each port to indicate the link activity of the port. Table 2 describes the functions of these LEDs.

    Table 2: 100-Gigabit Ethernet PIC with CFP2 LEDs

    Label

    Color

    State

    Description

    STATUS

    Green

    On steadily

    PIC is online with no alarms or failures.

    Yellow

    On steadily

    PIC is initializing.

    Red

    On steadily

    PIC has an error or failure.

    Off

    PIC is offline or not enabled and safe to remove from the router.

    Single LED per port

    Green

    On steadily

    Port is online with no alarms or errors, and the link is up.

    Blinking

    There is link activity on the port.

    Red

    On steadily

    Port is on but the link is down, and the port has detected a failure.

    Off

    Port is off or not enabled.

    Alarms, Errors, and Events

    • Laser bias current high/low alarms and warnings

    • Laser Rx power high/low alarms and warnings

    • Module not ready alarm

    • Module low power alarm

    • Module temperature high/low alarms and warnings

    • Rx CDR loss of lock alarm

    • Rx loss of signal alarm

    • Module not ready alarm

    • Tx CDR loss of lock alarm

    Modified: 2017-09-13