Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    100-Gigabit Ethernet OTN PIC with CFP2 (PTX Series)

    Software Release

    • PTX5000: Junos OS Release 14.1R2 and later

    Hardware Features

    • Four ports that can be configured as 100-Gigabit Ethernet, 100-Gigabit OTN, or a combination of 100-Gigabit Ethernet and 100-Gigabit Ethernet OTN interfaces.

    • Model number: P2-100GE-OTN

    • Name in the CLI: 4x100GE OTN CFP2

    • Power requirements: 14.50A@ –12 V (176 W)

    • Large maximum transmission units (MTUs): up to 9500 bytes

    Software Features

    Table 1 shows the first supported release for each software feature.

    Table 1: Software Features Supported

    Software Feature

    First Supported Junos OS Release on PTX5000

    Flexible Ethernet services encapsulation

    14.1R2

    Flexible VLAN tagging

    14.1R2

    IFINFO / IFMON

    14.1R2

    IEEE 802.1 ag OAM

    14.1R2

    IEEE 802.3 ah OAM

    14.1R2

    IEEE 802.3ad link aggregation

    14.1R2

    Interrupt-driven link-down detection for MPLS FRR

    14.1R2

    MAC accounting per logical interface for source addresses

    14.1R2

    MAC filter per port for destination addresses and source addresses

    14.1R2

    MAC filter per logical interface for source addresses

    14.1R2

    SNMP

    14.1R2

    Up to 4000 logical interfaces shared across all ports on a single PFE

    14.1R2

    Cables and Connectors

    The following transceivers are supported on this PIC:

    • CFP2-100G-LR4-D—Supports both 100GBASE-LR4 and OTU4 4I1-9D1F

      • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications or 100-Gigabit Ethernet OTN Optical Interface Specifications

      • Connector: LC

    • CFP2-100G-SR10-D—Supports 100GBASE-SR10

      Note: This transceiver supports Ethernet only, OTN is not supported.

      • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

      • Connector: 24-fiber MPO

    • CFP2-100GBASE-LR4—Supports 100GBASE-LR4

      • Cable: See 100-Gigabit Ethernet 100GBASE-R Optical Interface Specifications

      • Connector: LC

    • CFP2-100GBASE-SR10—Supports 100GBASE-SR10

      • Cable:

      • Connector: 24-fiber MPO

    LEDs

    The STATUS LED is located to the left of the ONLINE/OFFLINE button. One LED is located next to each port to indicate the link activity of the port. Table 2 describes the functions of these LEDs.

    Table 2: 100-Gigabit Ethernet OTN PIC with CFP2 LEDs

    Label

    Color

    State

    Description

    STATUS

    Green

    On steadily

    PIC is online with no alarms or failures.

    Yellow

    On steadily

    PIC is initializing.

    Red

    On steadily

    PIC is in failed state.

    Off

    PIC is offline or not enabled.

    Single LED per port, labeled 0, 1, 2, and 3

    Green

    On steadily

    Port is online with no alarms or failures, and the link is up.

    Blinking

    Activity detected. Port is sending or receiving packets.

    Red

    On steadily

    Port is on but the link is down, and the port has detected a failure with alarms.

    Off

    Port is off or not enabled.

    Modified: 2016-04-04