Port Query and Node Summary Examples
You can view port configuration settings by selecting Query Port from the Port Operations menu. This topic describes examples for Cisco HDLC configuration and Frame Relay configuration. Note that separate statistics are provided for each DLCI in the Frame Relay example.
The following output describes an example of Cisco HDLC configuration:
Detail query display for bridge port 2 =============================================================================== General status: Device name: scc2 Port admin state: ACTIVE Port link state: UP Serial interface: Interface: EIA-530A/DCE/NRZ Clock Config: 1024.000000 / Configured Rate, w/o Ext Tx Clk (TT) Measured TT(Ext Clock): 1023.999600 Encapsulation: CISCO HDLC HDLC keepalive status: up Bridge configuration: Interface/VLAN: eth0.202 AutoARP: enabled (1 ARP reply sent) AutoMAC: enabled Dst-MAC for TX pkts: 0012.1e71.85a1 (auto) Statistics: Serial RX packets: 301 (53 pps) Serial TX packets: 302 (53 pps) Serial RX bytes: 16888 (23744 bps) Serial TX bytes: 16912 (23744 bps) =============================================================================== Time since last port counter clear: 0 wks, 0 days, 0 hrs, 0 mins 19 secs Clear Port 2 Stats? y[n]:
The following output describes an example of Frame Relay configuration.
Detail query display for bridge port 2 =============================================================================== General status: Device name: scc2 Port admin state: ACTIVE Port link state: UP Serial interface: Interface: EIA-530A/DCE/NRZ Clock Config: 1024.000000 / Configured Rate, w/o Ext Tx Clk (TT) Measured TT(Ext Clock): 1023.999600 Encapsulation: FRAME RELAY Frame-relay LMI status: up Bridge configuration: Frame-relay DLCI: 301 (active) Interface/VLAN: eth0.301 AutoARP: enabled (1 ARP reply sent) AutoMAC: enabled Dst-MAC for TX pkts: 0012.1e71.85a1 (auto) Frame-relay DLCI: 302 (active) Interface/VLAN: eth0.302 AutoARP: enabled (0 ARP replies sent) AutoMAC: enabled Dst-MAC for TX pkts: ffff.ffff.ffff Statistics: DLCI 301: Serial RX packets: 4 (0 pps) Serial TX packets: 13 (0 pps) Serial RX bytes: 284 (0 bps) Serial TX bytes: 571 (0 bps) DLCI 302: Serial RX packets: 0 (0 pps) Serial TX packets: 0 (0 pps) Serial RX bytes: 0 (0 bps) Serial TX bytes: 0 (0 bps) ===============================================================================
To see all configured bridge ports at once, select Option 3, Node Summary, from the main Config menu.
========================================================================== = (nova_45 06/06/08 23:22:51 GMT) | CTP Main Menu ========================================================================== Please select a number from the following list: ------------------------------------- 0) Exit to Shell 1) Bundle Operations 2) Node Synchronization 3) Node Summary 4) Node Diagnostics 5) Node Operations 6) Save Running Database to Flash ------------ Your choice [3]: 3 CTP Code version : 7.3R7-rc3 200914 (Compile Time 08:14:36 PM) , Flash: Single Image >>>>> Circuit Emulation Ports <<<<< Port Bndl BndlTyp RemAddr CID LCID RunState NtSz PortRate RCtr ============================================================================== se-0/1 -- NotCfgd N/A N/A N/A DISABLD N/A 1024.000000 0 se-0/2 1 CTP 10.0.0.1 2 2 NoSYNC 1024 1024.000000 0 se-0/3 -- NotCfgd N/A N/A N/A CfgFAIL N/A 12288.000000 0 se-0/4 -- NotCfgd N/A N/A N/A DISABLD N/A 1024.000000 0 se-0/5 -- NotCfgd N/A N/A N/A DISABLD N/A 1024.000000 0 ============================================================================== Legend: ------- C - Card on which port resides p - Physical port on card Bndl - Bundle number port is assigned to BndlTyp - Bundle type RemAddr - Remote address CIDs - Bundle Type: CID : LCID - CTP: Remote Circuit ID : Local Circuit ID - SAToP: Source UDP Port : N/A - CESoPSN: Source UDP Port : N/A RunState - Bundle's local run state (i.e. DISABLD, NoSync, RUNNING, etc...) NtSz - Configured packet size for NET bound packets PortRate - Configured data rate towards network RCtr - Bundle's local buffer recenter event counter Hit Carriage Return to Continue... >>>> PBS Interfaces <<<<< Port Encap Inet Addr p-t-p Addr Status PortRate MTU ================================================================================ se-0/6 Cisco HDLC 0.0.0.0 0.0.0.0 DISABLED 1024.000000 1500 se-0/7 Cisco HDLC 0.0.0.0 0.0.0.0 DISABLED 1024.000000 1500 ================================================================================ >>>>> Bridged Ports <<<<< ( pps/port allocation: 552375 pps ) Port/PVC Ethernet Encap Admin Link Proto Dest MAC =============================================================================== se-0/0 eth0.0 chdlc down down down ffff.ffff.ffff =============================================================================== Hit Carriage Return to Continue... Bndl BndlTyp Port TS RemAddr CID LCID RunState NtSz IfSz RCtr =============================================================================== 0 CTP se-0/3 N/A 10.0.0.1 3 3 CfgFAIL 1024 -- 0 1 CTP se-0/2 N/A 10.0.0.1 2 2 NoSYNC 1024 -- 0 =============================================================================== Legend: ------- Bndl - Bundle number port is assigned to BndlTyp - Bundle type Card - Local card with port. Port - Local port on card. TS - Time slot(s) in bundle. RemAddr - Remote address. CIDs - Bundle Type: CID : LCID - CTP: Remote Circuit ID : Local Circuit ID - SAToP: Source UDP Port : N/A - CESoPSN: Source UDP Port : N/A RunState - Bundle's local run state (i.e. DISABLD, NoSYNC, RUNNING, etc...) NtSz - Configured packet size for NET bound packets IfSz - Packet size for Interface bound packets RCtr - Bundle's local buffer recenter event counter