Multi-Rate Ethernet MIC

Software release

• JNP-MIC1:

  Junos OS release 17.3R1 and later

• JNP-MIC1-MACSEC:

  Junos OS release 17.3R2 and later

• MIC-MACSEC-MRATE:

  Junos OS release 17.4R1 and later

For information about which MPCs support this MIC, see MIC/MPC Compatibility. For information about which MICs are supported on MX Series routers, see MICs Supported by MX Series Routers.

Description

• Weight: 3 lb (1.36 kg)

• Model numbers:

  Without MACsec support: JNP-MIC1

  With MACsec support: JNP-MIC1-MACSEC

  With MACsec support: MIC-MACSEC-MRATE

• Power requirement:

  • JNP-MIC1:

    85 W at 55° C

    80 W at 25° C

  • JNP-MIC1-MACSEC:

    130 W at 55° C

    125 W at 25° C

  • MIC-MACSEC-MRATE:

    110 W at 45° C

    105 W at 25° C

• Name in the CLI:

  JNP-MIC1: MIC1

  JNP-MIC1-MACSEC: MIC1-MACSEC

  MIC-MACSEC-MRATE: MACSEC-12xQSFPP-XGE-XLGE-CGE

Hardware features

• JNP-MIC1 and JNP-MIC1-MACSEC:

  • Twelve 100-Gigabit Ethernet ports that support quad small form-factor pluggable (QSFP28) transceivers

  • The ports are numbered 0 through 11.

  • Each port can be configured as a 100-Gigabit Ethernet port, 40-Gigabit Ethernet port, or as four 10-Gigabit Ethernet ports (by using a breakout cable).

  Table 1 lists the configurable Gigabit Ethernet port speeds for each port.

• MIC-MACSEC-MRATE:

  • Twelve Gigabit Ethernet QSFP+ ports, each of which can be configured as a 40-Gigabit Ethernet port or as four 10-Gigabit Ethernet ports (by using a breakout cable).

  • The ports are numbered 0 through 11.

  • Eight out of the twelve ports can be configured as 100-Gigabit Ethernet ports. Port numbers 0 through 3, and 6 through 9 are the eight 100-Gigabit Ethernet ports.

  • When used in MP8CE:

    • Four ports out of the total twelve ports support 100-Gigabit Ethernet speed

    • Maximum aggregate port capacity across ports 0 through 5 should not exceed 240 Gbps

    • Maximum aggregate port capacity across ports 6 through 11 should not exceed 240 Gbps

  • When used in MPC9E:

    • Eight ports out of the total twelve ports support 100-Gigabit Ethernet speed

    • Maximum aggregate port capacity across ports 0 through 5 should not exceed 400 Gbps

    • Maximum aggregate port capacity across ports 6 through 11 should not exceed 400 Gbp

  Note:

  Compared to other MICs, MIC-MACSEC-MRATE takes longer time (around 4 minutes) to boot as it is required to bring up two MICs in serial.

  Table 2 lists the configurable Gigabit Ethernet port speeds for each port.

Software features

• Supports rate selectability at the port level.

• By default, the ports are configured as 10-Gigabit Ethernet ports.

• Supports remote port identification.

• MICs with model numbers JNP-MIC1-MACSEC and MIC-MACSEC-MRATE support Media Access Control Security (MACsec)

Cables and connectors

The list of supported transceivers for the MX Series is located at https://pathfinder.juniper.net/hct/category/#catKey=100001&modelType;=All&pf;=MX+Series.

LEDs

• OK/FAIL LED, one bicolor:

  • OFF—MIC is offline or MIC has fault.

  • Red—MIC is in power failure state.

  • Green—MIC is online.

• Link LED, one green per port:

  • Steady green—Link is up.

  • Off—Link is down or disabled.

• Like port status LED, each individual lane LED support four states as: OFF, AMBER, GREEN, RED. See MPC and MIC Lane LED Scheme Overview for more details.