Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

ON THIS PAGE

Modifying a Full Mesh IP Service

 

For a full mesh IP service, you can add a new device endpoint, add or delete a UNI, change routing protocol parameters, remove or add static routes, change IP addresses, swap between BGP and static routing protocols (if service definition specifies BGP and Static), swap between OSPF and static routing protocols (if service definition specifies OSPF and Static).

Note

You cannot change the interface of an existing UNI. To perform the equivalent of changing the interface on an existing UNI, add a new UNI with the desired interface, and then delete the old UNI.

After modifying a service, the configuration audit and functional audit information is cleared and the functional audit status is set to pending.

If there is a service template attached to the service definition, there is a link to that template at the bottom of the Endpoint Settings section of the window. For instructions on working with service templates in service orders, see Creating a Service Order Based on a Service Definition with a Template.

Modifying a service creates a new service order based on the attribute settings of the existing service.

Note

When you modify a service or a service order, the read-only fields in the different pages of the wizard for service or service order modification are grayed out to indicate that you cannot modify those attributes.

Adding an Endpoint

To add an endpoint to a multipoint-to-multipoint Ethernet service:

  1. In the Network Services > Connectivity task pane, select Service Provisioning > Manage Services.
  2. In the Manage Services page, select the service to which you want to add an endpoint.
  3. Click the Modify icon at the top of the page that displays the previously created service orders.

    The Modify Service page appears.

    Current service settings appear in the main display area. The General Information box contains a unique name for the service order that will request the change.

  4. In the Order name field, change the name of the modification service order, if desired.
  5. Click the Node Settings button to view the endpoints or devices that are associated with the service.
  6. In the Service Nodes table, click Add.

    The Choose Endpoints window shows available N-PE devices that are not part of the service.

  7. Select the devices and the interfaces corresponding to the selected devices on which you want to add new endpoints, then click OK. You are returned to the Node Settings page of the Manage Service Orders wizard.

    To filter and sort the display of objects, enter the name of the object as a match criterion in the Search box and click the Search icon. The page refreshes to display only the object names that match with the search term. You can use the paging controls to navigate across multiple pages of objects as necessary.

    The service modification window shows the added devices with system recommended choices for UNI.

  8. Select the devices on which you want to add new endpoints, and then click Next.

    The service modification window shows the added devices with system recommended choices for UNI. To select a different UNI, see Adding a UNI Interface.

  9. Click Finish to save the modified service order. You are returned to the Manage Service Orders page.
  10. In Deploy mode of the Service View of Connectivity Services Director, select one of the following:

    • Deploy now to deploy modified service immediately when you click, OK

    • Schedule deployment to specify a date and time to deploy the modified service later. The default time is the current date and time when you select the option.

  11. Click OK.

    The service modification deployment job ID is assigned.

  12. Click the Job ID.

    You see the service modification deployment job details in the System > Manage Jobs > Job Management page. The Job Management page presents the job information by job ID, Name, Percent complete, State, Job Type, Summary, Scheduled Start, Username, and Recurrence. The State column indicates whether the modified service deployment is successful.

    Note

    Alternatively, to display the Job Management page, from the Junos Space Platform UI, select Jobs > Manage Jobs from the Tasks pane. You can also view the CSD Deployment Jobs page in Deploy mode of Service View by selecting the View Deployment Jobs option in the task pane.

Adding a UNI Interface

To add a UNI on a device that is already part of a multipoint-to-multipoint Ethernet service:

  1. In the Network Services > Connectivity task pane, select Service Provisioning > Manage Services.
  2. In the Manage Services page, select the service to which you want to add a UNI.
  3. Click the Modify icon at the top of the page that displays the previously created service orders.

    Current service settings appear in the main display area. The General Settings box contains a unique name for the service order that will request the change.

  4. In the service Order name field, change the name of the modification service order, if desired.
  5. Click the Site/Endpoint Settings button to view the interfaces on endpoints or devices that are associated with the service.
  6. In the User-to-Network Interfaces table, click Add.

    The Choose Endpoints window shows available N-PE devices that are not part of the service.

  7. Select the devices on which you want to add new interfaces. The window refreshes to display all the user-to-network (UNI) or ingress interfaces for the selected device in the lower part of the window as a tabular grid. Select the interfaces that you want to assign to the service order, and then click OK.

    To filter and sort the display of objects, enter the name of the object as a match criterion in the Search box and click the Search icon. The page refreshes to display only the object names that match with the search term. You can use the paging controls to navigate across multiple pages of objects as necessary.

    Based on the devices you select in the top half of the dialog box, the interfaces that are present in the selected device are displayed in the lower half of the dialog box. Select the check boxes next to the interfaces that you want to associate with the service.

    You are returned to the Node Settings page of the Manage Service Orders wizard.

  8. The Interface IP field displays the interface IP address.
  9. The Autopick VLAN ID check box is selected by default to allow Network Activate to select a VLAN ID. If you deselect the Autopick VLAN ID check box, you must either enter a different value in the service VLAN ID field manually.
  10. Select a routing protocol from the drop-down list box.
  11. Click Modify.
  12. Click Modify.

    You can now deploy the modified service.

  13. In the Deployment Options dialog box, select one of the following:

    • Save only and Validate to save the service modification and validate it.

    • Deploy now to deploy modified service immediately when you click, OK

    • Schedule deployment to specify a date and time to deploy the modified service later. The default time is the current date and time when you select the option.

  14. Click OK.

    The service modification deployment Job ID link appears.

  15. Click the Job ID.

    You see the service modification deployment job details in the System > Manage Jobs > Job Management page. The Job Management page presents the job information by job ID, Name, Percent complete, State, Job Type, Summary, Scheduled Start, Username, and Recurrence. The State column indicates whether the modified service deployment is successful.

    Note

    Alternatively, to display the Job Management page, from the Junos Space Platform UI, select Jobs > Manage Jobs from the Tasks pane. You can also view the CSD Deployment Jobs page in Deploy mode of Service View by selecting the View Deployment Jobs option in the task pane.

Deleting a UNI Interface and Deleting an Endpoint

To delete a UNI from a multipoint-to-multipoint Ethernet service:

  1. In the Network Services > Connectivity task pane, select Service Provisioning > Manage Services.
  2. In the Manage Services page, select the service from which you want to delete a UNI.
  3. Click the Modify icon at the top of the page that displays the previously created service orders.

    Current service settings appear in the main display area. The General Settings box contains a unique name for the service order that will request the change.

  4. In the service Order name field, change the name of the modification service order, if desired.
  5. Click the Site/Endpoint Settings button to view the interfaces on endpoints or devices that are associated with the service.
  6. In the User-to-Network Interfaces table, click Add.

    The Choose Endpoints window shows available N-PE devices that are not part of the service.

  7. Select the devices on which you want to add new interfaces. The window refreshes to display all the user-to-network (UNI) or ingress interfaces for the selected device in the lower part of the window as a tabular grid. Select the interfaces that you want to assign to the service order, and then click OK.

    To filter and sort the display of objects, enter the name of the object as a match criterion in the Search box and click the Search icon. The page refreshes to display only the object names that match with the search term. You can use the paging controls to navigate across multiple pages of objects as necessary.

    Based on the devices you select in the top half of the dialog box, the interfaces that are present in the selected device are displayed in the lower half of the dialog box. Select the check boxes next to the interfaces that you want to associate with the service.

    You are returned to the Node Settings page of the Manage Service Orders wizard.

    The service modification window shows the added devices with system recommended choices for UNI.

  8. Click Finish to complete the modification of the service order and save the settings.
  9. In Deploy mode of the Service View of the Connectivity Services Director, select one of the following from the Manage Services page:

    • Schedule the change for immediate deployment.

    • Schedule the change for later deployment.

  10. You see the service modification deployment job details in the System > Jobs > Job Management page. The Job Management page presents the job information by job ID, Name, Percent Complete, State, Job Type, Summary, Scheduled Start, Username, and Recurrence. The State column indicates whether the modified service deployment is successful.Note

    Alternatively, to display the Job Management page, from the Junos Space Platform UI, select Jobs > Manage Jobs from the Tasks pane. You can also view the CSD Deployment Jobs page in Deploy mode of Service View by selecting the View Deployment Jobs option in the task pane.

Related Documentation