Nortel Multiprotocol Router

The Nortel Multiprotocol Router DSM for JSA records all relevant Nortel Multiprotocol Router events by using syslog.

Before you configure JSA to integrate with a Nortel Multiprotocol Router device, you must:

1. Log in to your Nortel Multiprotocol Router device.
2. At the prompt, type the following command:

   bcc

   The Bay Command Console prompt is displayed.

   Welcome to the Bay Command Console!

   * To enter configuration mode, type config

   * To list all system commands, type ?

   * To exit the BCC, type exit

   bcc>

3. Type the following command to access configuration mode:

   config

4. Type the following command to access syslog configuration:

   syslog

5. Type the following commands:

   log-host address <IP address>

   Where <IP address> is the IP address of your JSA.

6. View current default settings for your JSA:

   info

   For example:

   log-host/10.11.12.210# info

   address 10.11.12.210

   log-facility local0

   state enabled

7. If the output of the command entered in Step 5 indicates that the state is not enabled, type the following command to enable forwarding for the syslog host:

   state enable

8. Configure the log facility parameter:

   log-facility local0

9. Create a filter for the hardware slots to enable them to forward the syslog events. Type the following command to create a filter with the name WILDCARD:

   filter name WILDCARD entity all

10. Configure the slot-upper bound parameter:

    slot-upper bound <number of slots>

    Where <number of slots> is the number of slots available on your device. This parameter can require different configuration which depends on your version of Nortel Multiprotocol Router device, which determines the maximum number of slots available on the device.

11. Configure the level of syslog messages you want to send to your JSA.

    severity-mask all

12. View the current settings for this filter:

    info

    For example:

    filter/10.11.12.210/WILDCARD# info

    debug-map debug

    entity all

    event-lower-bound 0

    event-upper-bound 255

    fault-map critical

    info-map info

    name WILDCARD

    severity-mask {fault warning info trace debug}

    slot-lower-bound 0

    slot-upper-bound 1

    state enabled

    trace-map debug

    warning-map warning

13. View the currently configured settings for the syslog filters:

    show syslog filters

    When the syslog and filter parameters are correctly configured, the Operational State indicates up.

    For example:

    syslog# show syslog filters

    show syslog filters Sep 15, 2008 18:21:25 [GMT+8]

    Table 1: Syslog Filters

    Host IP address	Filter Name	Entity Name	Entity Code	Configured State	Operational State
    10.11.12.130	WILDCARD	all	255	enabled	up
    10.11.12.210	WILDCARD	all	255	enabled	up

14. View the currently configured syslog host information:

    show syslog log-host

    The host log is displays the number of packets that are going to the various syslog hosts.

    For example:

    syslog# show syslog log-host

    show syslog log-host Sep 15, 2008 18:21:32 [GMT+8]

    Table 2: Syslog Host Log

    Host IP address	Configured State	Operational State	Time Sequencing	UDP Port	Facility Code	#Messages Sent
    10.11.12.130	enabled	up	disabled	514	local0	1402
    10.11.12.210	enabled	up	disabled	514	local0	131

15. Exit the command-line interface:

    1. Exit the current command-line to return to the bcc command-line:

       exit

16. Exit the bbc command-line:

    exit

17. Exit the command-line session:

    logout

18. You can now configure the log source in JSA.

    To configure JSA to receive events from a Nortel Multiprotocol Router device:

    1. From the Log Source Type list, select the Nortel Multiprotocol Router option.