Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    Node Menu Protocol Status

    In the IP/MPLSView main window, select a node in the map, right-click, and select Protocol Status. The Protocol Status menu is displayed. Figure 1 shows the Protocol Status menu.

    Figure 1: Protocol Status Menu

    Protocol Status Menu

    In the IP/MPLSView main window, select a node in the map, right-click, and select Protocol Status>BGP Neighbors at Node. The BGP Neighbors at Node window is displayed. Figure 2 shows the BGP Neighbors at Node window.

    Figure 2: Protocol Status BGP Neighbors Window

    Protocol
Status BGP Neighbors Window

    Table 1 describes the BGP Neighbors at Node table columns.

    Table 1: BGP Neighbors at Node Table Columns

    Column Name

    Description

    Name

    Name of the node that is a BGP speaker. If the node is a logical system configured on a physical device, the logical system name is displayed in parentheses.

    AS

    Autonomous system number of the node.

    Interface

    Interface used to establish the neighbor peer session.

    Neighbor Node

    Name of the node that is the BGP neighbor peer.

    Neighbor AS

    Autonomous system number of the node that is the BGP neighbor peer.

    Neighbor Address

    IP address of the node that is the BGP neighbor peer.

    Group

    The name of the peer group, if applicable.

    The BGP group is configured under [edit protocols bgp group ibgp_peers] on Juniper devices.

    In Policy

    All policies that are applied to incoming routes from the neighbor.

    Out Policy

    All policies that are applied to outgoing routes from the node.

    Address Family

    The protocol address families supported on the router and configured on the interface (inet, inet-vpn, L2vpn, BGP-LU, ipv6).

    Status

    The state of the BGP peer relationship. Established is the key state which indicates peers are operationally up and BGP route updates are exchanged. BGP Peering Operation Status is Up only if peering state is established. Any other peering state collected (idle, connect, active, opensent, or openconfirm) implies BGP Peering Operational Status is Down.

    BGPPeerFsmEstablishedTime

    How long this peer has been in the established state or how long since this peer was last in the established state. It is set to zero when a new peer is configured or the router is booted.

    Last Updated

    The time the information was last updated.

    In the IP/MPLSView main window, select a node in the map, right-click, and select Protocol Status>OSPF Neighbors at Node. The OSPF Neighbors at Node window is displayed. Figure 3 shows the OSPF Neighbors at Node window.

    Figure 3: Protocol Status OSPF Neighbors Window

    Protocol
Status OSPF Neighbors Window

    Table 2 describes the OSPF Neighbors at Node table columns.

    Table 2: OSPF Neighbors at Node Table Columns

    Column Name

    Description

    Node A

    Name of the node.

    RouterID_A

    OSPF router ID of the node.

    Interface_A

    Interface used to establish the OSPF neighbor adjacency.

    IP_A

    IP address of node A used to establish the OSPF neighbor adjacency.

    Node_Z

    Name of the node that is the OSPF neighbor.

    RouterID_Z

    OSPF router ID of the neighbor node.

    Interface_Z

    Interface on the neighbor node used to establish the OSPF neighbor adjacency.

    IP_Z

    IP address of the neighbor node used to establish the OSPF neighbor adjacency.

    Priority

    The OSPF priority used to determine which router is selected as the designated router (DR) or backup designated router (BDR) of the area.

    State

    The state of the OSPF neighbor adjacency (down, attempt, init, twoWay, exchangeStart, exchange, loading, full, or unknown).

    Last Updated

    The time the information was last updated.

    In the IP/MPLSView main window, select a node in the map, right-click, and select Protocol Status>ISIS Adjacencies at Node. The ISIS Adjacencies at Node window is displayed. Figure 4 shows the ISIS Adjacencies at Node window.

    Figure 4: Protocol Status ISIS Adjacencies Window

    Protocol
Status ISIS Adjacencies Window

    Table 3 describes the ISIS Adjacencies at Node table columns.

    Table 3: ISIS Adjacencies at Node Table Columns

    Column Name

    Description

    Node A

    Name of the node.

    SysIdA

    IS-IS system ID of the node.

    Interface_A

    Interface used to establish the IS-IS neighbor adjacency.

    IP_A

    IP address used to establish the IS-IS neighbor adjacency.

    Node Z

    Name of the node that is the ISIS neighbor.

    SysIdZ

    IS-IS system ID of the neighbor node.

    Interface_Z

    Interface on the neighbor node used to establish the ISIS neighbor adjacency.

    IP_Z

    IP address of the neighbor node used to establish the ISIS neighbor adjacency.

    Priority

    The IS-IS priority used to determine the designated router on a broadcast network.

    State

    The state of the IS-IS neighbor adjacency (up, down, initializing, failed, or unknown).

    Type

    Adjacency type (L1, L2, or L12).

    Last Updated

    The time the information was last updated.

    In the IP/MPLSView main window, select a node in the map, right-click, and select Protocol Status>Tunnels at Node. The Tunnels at Node window is displayed. Figure 5 shows the Tunnels at Node window.

    Figure 5: Protocol Status Tunnels at Node Window

    Protocol
Status Tunnels at Node Window

    Table 4 describes the Tunnels at Node table columns.

    Table 4: Tunnels at Node Table Columns

    Column Name

    Description

    Name

    Name of the tunnel.

    Node A

    Name of node A at one end of the tunnel.

    IP_A

    IP address of node A at one end of the tunnel.

    Node Z

    Name of node Z at one end of the tunnel.

    IP_Z

    IP address of node Z at one end of the tunnel.

    Role

    The MPLS-TE tunnel role (head, transit, tail, or headTail).

    Admin Status

    Current status of the tunnel (Unknown, Install, Active, Live, Order, or Planned).

    Oper Status

    The operational status of the tunnel. (up, down, testing, unknown, dormant, notpresent, or lowerLayerDown)

    Tunnel Up Time

    The elapsed time since the tunnel came up.

    Last Updated

    The time the information was last updated.

    Modified: 2017-04-04