Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
 

SONET/SDH OC192c/STM64 PIC

Software release

  • Junos 9.4 and later

Description

  • One OC192 port

  • Power requirement: 0.45 A @ 48 V (21.6 W)

  • Model Number: PC-1OC192-SON-VSR

Hardware features

  • Multiplexing and demultiplexing

  • Rate policing on input

  • Rate shaping on output

  • Packet buffering, Layer 2 parsing

Software features

  • SONET/SDH framing

  • Link aggregation

  • Alarm and event counting and detection

  • Dual-router automatic protection switching (APS)

  • Multiprotocol Label Switching (MPLS) fast reroute

  • Encapsulations:

    • High-Level Data Link Control (HDLC)

    • Frame Relay

    • Circuit cross-connect (CCC)

    • Translational cross-connect (TCC)

    • Point-to-Point Protocol (PPP)

Cables and connectors

Tip:

You can use the Hardware Compatibility Tool to find information about the pluggable transceivers supported on your Juniper Networks device.

The list of supported transceivers for the MX Series is located at https://pathfinder.juniper.net/hct/category/#catKey=100001&modelType;=All&pf;=MX+Series.

  • Very short reach (VSR 1): 12-ribbon multimode fiber with MTP connector (Rx and Tx)

  • Fiber-optic 10-gigabit small form-factor pluggable (XFP) transceivers: 10GBASE-S very short reach (VSR-1) (model number: XFP-10G-S)

Note:

To extend the life of the laser, when a PIC is not being actively used with any valid links, take the PIC offline until you are ready to establish a link to another device. For information about taking a PIC offline, see the request chassis pic offline command in the CLI Explorer.

LEDs

One tricolor LED per port:

  • Off—Not enabled

  • Green—Online with no alarms or failures

  • Yellow—Online with alarms for remote failures

  • Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events

  • SONET alarms:

    • Alarm indication signal—line (AIS-L)

    • Alarm indication signal—path (AIS-P)

    • Bit error rate—signal degrade (BERR-SD)

    • Bit error rate—signal fail (BERR-SF)

    • Bit interleaved parity (BIP) error B1, B2, B3

    • Far-end bit error: remote error indication—line (REI-L), far-end line coding violations (CV-LFE)

    • Far-end bit error: remote error indication—path (REI-P), far-end path coding violations (CV-PFE)

    • Loss of frame (LOF)

    • Loss of pointer (LOP-P)

    • Loss of signal (LOS)

    • Payload label mismatch (PLM-P)

    • Payload unequipped (unequipped STS at path level) (UNEQ-P)

    • Remote defect indication—line (RDI-L)

    • Remote defect indication—path (RDI-P)

  • SDH alarms:

    • Administrative unit alarm indication signal (AU-AIS)

    • Bit error rate signal degrade (BERR-SD)

    • Bit error rate signal fail (BERR-SF)

    • Bit interleaved parity (BIP) error B1, B2, B3

    • Higher order path—payload label mismatch (HP-PLM)

    • Higher order path—loss of pointer (HP-LOP)

    • Higher order path—remote defect indication (HP-RDI)

    • Higher order path—unequipped (HP-UNEQ)

    • Loss of frame (LOF)

    • Loss of signal (LOS)

    • Multiplex section—alarm indication signal (MS-AIS)

    • Multiplex section—remote defect indication (MS-RDI)

    • Multiplex section—remote error indication (MS-REI)

  • Error detection:

    • Errored seconds (ES-S, ES-L, ES-P)

    • Far-end errored seconds (ES-LFE, ES-PFE)

    • Far-end severely errored seconds (SES-LFE, SES-PFE)

    • Far-end unavailable seconds (UAS-LFE, UAS-PFE)

    • Severely errored framing (SEF)

    • Severely errored framing seconds (SEFS-S)

    • Severely errored seconds (SES-S, SES-L, SES-P)

    • Unavailable seconds (UAS-L, UAS-P)