ON THIS PAGE
Example: Configuring a Static PPPoE Subscriber Interface on a Static Underlying VLAN Demux Interface over Aggregated Ethernet
This example shows how you can configure static PPPoE subscriber interfaces over aggregated Ethernet bundles to provide subscriber link redundancy.
Requirements
PPPoE over VLAN demux interfaces over aggregated Ethernet requires the following hardware and software:
MX Series 5G Universal Routing Platforms
MPCs
Junos OS Release 11.2 or later
No special configuration beyond device initialization is required before you can configure this feature.
Overview
Aggregated Ethernet bundles enable link redundancy between the router and networking devices connected by Ethernet links. This example describes how to configure link redundancy for static PPPoE subscribers over aggregated Ethernet interface with an intermediate static VLAN demux interface. Sample tasks include configuring a two-member aggregated Ethernet bundle on ae0, configuring a static VLAN demux interface, demux0.100, that underlies the PPPoE subscriber interface, pp0.100, and configuring the PPPoE subscriber interface including characteristics of the PPPoE family.
This example does not show all possible configuration choices.
Configuration
Procedure
CLI Quick Configuration
To quickly configure link redundancy for static PPPoE subscribers over a static VLAN demux interface over aggregated Ethernet, copy the following commands, paste them in a text file, remove any line breaks, and then copy and paste the commands into the CLI.
[edit] set chassis aggregated-devices ethernet device-count 1 set interfaces ge-5/0/3 gigether-options 802.3ad ae0 set interfaces ge-5/0/3 gigether-options 802.3ad primary set interfaces ge-5/1/2 gigether-options 802.3ad ae0 set interfaces ge-5/1/2 gigether-options 802.3ad backup set interfaces ae0 flexible-vlan-tagging set interfaces ae0 aggregated-ether-options link-protection edit interfaces demux0 unit 100 set vlan-id 100 set demux-options underlying-interface ae0 set family pppoe access-concentrator pppoe-server-1 set family pppoe duplicate-protection set family pppoe max-sessions 16000 top edit interfaces pp0 unit 100 set pppoe-options underlying-interface demux0.100 set pppoe-options server set family inet unnumbered-address lo0.0 top
Step-by-Step Procedure
The following example requires you to navigate various levels in the configuration hierarchy. For instructions on how to do that, see Using the CLI Editor in Configuration Mode.
To configure link redundancy for static PPPoE subscribers over a static VLAN demux interface over aggregated Ethernet:
Define the number of aggregated Ethernet devices on the router.
[edit chassis] user@host# set aggregated-devices ethernet device-count 1
Configure a two-link aggregated Ethernet logical interface to serve as the underlying interface for the static VLAN demux subscriber interface. In this example, the LAG bundle is configured for one-to-one active/backup link redundancy. To support link redundancy at the MPC level, the LAG bundle attaches to ports from two different MPCs.
[edit interfaces] user@host# set ge-5/0/3 gigether-options 802.3ad ae0 user@host# set ge-5/0/3 gigether-options 802.3ad primary user@host# set ge-5/1/2 gigether-options 802.3ad ae0 user@host# set ge-5/1/2 gigether-options 802.3ad backup
Enable link protection on the aggregated Ethernet logical interface and configure support for single and dual (stacked) VLAN tags.
[edit interfaces] user@host# set ae0 aggregated-ether-options link-protection user@host# set ae0 flexible-vlan-tagging
Configure the VLAN demux interface over the aggregated Ethernet logical interface.
[edit interfaces] user@host# set demux0 unit 100 vlan-id 100 user@host# set demux0 unit 100 demux-options underlying-interface ae0
Configure the PPPoE family attributes on the VLAN demux interface.
[edit interfaces] user@host# set demxu0 unit 100 family pppoe access-concentrator pppoe-server-1 user@host# set demux0 unit 100 family pppoe duplicate-protection user@host# set demux0 unit 100 family pppoe max-sessions 16000
Configure the VLAN demux interface as the underlying interface on which the PPPoE logical interface is created.
[edit interfaces] user@host# set pp0 unit 100 pppoe-options underlying-interface demux0.100 user@host# set pp0 unit 100 pppoe-options server user@host# set pp0 unit 100 family inet unnumbered-address lo0.0
Results
From configuration mode, confirm the aggregated device configuration by entering the show chassis command. Confirm the interface configuration by entering the show interfaces command. If the output does not display the intended configuration, repeat the configuration instructions in this example to correct it.
[edit]
user@host# show chassis
aggregated-devices {
ethernet {
device-count 1;
}
}
[edit]
user@host# show interfaces
ge-5/0/3 {
gigether-options {
802.3ad {
ae0;
primary;
}
}
}
ge-5/1/2 {
gigether-options {
802.3ad {
ae0;
backup;
}
}
}
ae0 {
flexible-vlan-tagging;
aggregated-ether-options {
link-protection;
}
}
demux0 {
unit 100 {
vlan-id 100;
demux-options {
underlying-interface ae0;
}
family pppoe {
access-concentrator pppoe-server-1;
duplicate-protection;
max-sessions 16000;
}
}
}
pp0 {
unit 100 {
pppoe-options {
underlying-interface demux0.100;
server;
}
family inet {
unnumbered-address lo0.0;
}
}
}
If you are done configuring the device, enter commit from configuration mode.
Verification
To confirm that the configuration is working properly, perform these tasks:
- Verifying the Aggregated Ethernet Interface Configuration
- Verifying the demux0 Interface Configuration
- Verifying the pp0 Interface Configuration
Verifying the Aggregated Ethernet Interface Configuration
Purpose
Verify that the interface values match your configuration, the link is up, and traffic is flowing.
Action
From operational mode, enter the show interfaces redundancy command.
user@host> show interfaces redundancy Interface State Last change Primary Secondary Current status ae0 On primary ge-5/0/3 ge-5/1/2 both up
From operational mode, enter the show interfaces ae0 command.
user@host> show interfaces ae0
Physical interface: ae0, Enabled, Physical link is Up
Interface index: 128, SNMP ifIndex: 606
Link-level type: Ethernet, MTU: 1522, Speed: 1Gbps, BPDU Error: None,
MAC-REWRITE Error: None, Loopback: Disabled, Source filtering: Disabled,
Flow control: Disabled, Minimum links needed: 1, Minimum bandwidth needed: 0
Device flags : Present Running
Interface flags: SNMP-Traps Internal: 0x4000
Current address: 00:00:5e:00:53:d0, Hardware address: 00:00:5e:00:53:d0
Last flapped : 2011-03-11 13:24:18 PST (2d 03:34 ago)
Input rate : 1984 bps (2 pps)
Output rate : 0 bps (0 pps)
Logical interface ae0.32767 (Index 69) (SNMP ifIndex 709)
Flags: SNMP-Traps 0x4004000 VLAN-Tag [ 0x0000.0 ] Encapsulation: ENET2
Statistics Packets pps Bytes bps
Bundle:
Input : 371259 2 46036116 1984
Output: 0 0 0 0
Protocol multiservice, MTU: Unlimited
Flags: Is-PrimaryMeaning
The show interfaces redundancy output shows the redundant link configuration and that both link interfaces are up. The show interfaces ae0 output shows that the aggregated Ethernet interface is up and that traffic is being received on the logical interface.
Verifying the demux0 Interface Configuration
Purpose
Verify that the VLAN demux interface displays the configured PPPoE family attributes and the member links in the aggregated Ethernet bundle.
Action
From operational mode, enter the show interfaces demux0 command.
user@host> show interfaces demux0.100
Logical interface demux0.100 (Index 76) (SNMP ifIndex 61160)
Flags: SNMP-Traps 0x4000 VLAN-Tag [ 0x8100.100 ]
Encapsulation: ENET2
Demux:
Underlying interface: ae0 (Index 199)
Link:
ge-5/0/3
ge-5/1/2
Input packets : 2
Output packets: 18575
Protocol pppoe
Dynamic Profile: none,
Service Name Table: None,
Max Sessions: 16000, Duplicate Protection: On,
AC Name: pppoe-server-1Alternatively, you can enter show pppoe underlying-interfaces detail to display the state and PPPoE family configuration for all configured underlying interfaces.
Meaning
The output shows the name of the underlying interface, the member links of the aggregated bundle, and the PPPoE family configuration. The output shows packet counts when traffic is present on the logical interface.
Verifying the pp0 Interface Configuration
Purpose
Verify that the interface values match your configuration.
Action
From operational mode, enter the show interfaces pp0 command.
user@host> show interfaces pp0.100
Logical interface pp0.100 (Index 71) (SNMP ifIndex 710)
Flags: Point-To-Point SNMP-Traps 0x4000 Encapsulation: PPPoE
PPPoE:
State: SessionUp, Session ID: 1,
Session AC name: pppoe-server-1, Remote MAC address: 00:00:5e:00:53:34,
Underlying interface: demux0.100 (Index 70)
Link:
ge-5/0/3.32767
ge-5/1/2.32767
Input packets : 18572
Output packets: 18572
Keepalive settings: Interval 10 seconds, Up-count 1, Down-count 3
Keepalive: Input: 0 (never), Output: 18566 (00:00:02 ago)
LCP state: Opened
NCP state: inet: Opened, inet6: Not-configured, iso: Not-configured, mpls:
Not-configured
CHAP state: Closed
PAP state: Success
Protocol inet, MTU: 1500
Flags: Sendbcast-pkt-to-re
Addresses, Flags: Is-Primary
Local: 45.63.24.1Meaning
This output shows information about the PPPoE logical interface created on the underlying VLAN demux interface. The output includes the PPPoE family and aggregated Ethernet redundant link information, and shows input and output traffic for the PPPoE interface.