protocols (DDoS) (ACX Series, PTX Series, and QFX Series)

Syntax (ACX Series Routers)

Syntax (PTX Series Routers and QFX Series Switches)

Syntax (PTX Series and ACX7100-48L for Junos OS Evolved)

Hierarchy Level

Description

Change default configurable control plane DDoS protection policer parameters for all packet types within a protocol group or for a particular packet type within a protocol group.

Note:

PTX10003 router doesn’t support the priority option to change default priority values for aggregate or individual packet type policers. QFX10002-60C switches and PTX Series routers do not support the bypass-aggregate option.

Note:

Although the term bandwidth usually refers to bits per second (bps), this feature’s bandwidth option represents a packets per second (pps) value, and the burst option represents number of packets in a burst. These options are explained separately.

Not all protocol groups and packet types listed in Table 1 or Table 2 are supported on all devices. Exceptions include:

ACX Series routers support only the following protocol group options: arp, bfd, bfdv6, bgp, dhcpv4v6, eoam, esmc, igmp, ipmcast-miss (unknown multicast packets), isis, lacp, ldp, lldp, ndpv6, oam-lfm, ospf, pim, pvstp, rip, rsvp, stp, and vrrp.
PTX10003 and PTX10008 routers do not support the following policer protocol group options: all-fiber-channel-enode, bridge-control, diameter, garp-reply, l2pt, ptp, radius, and tacacs.
Other PTX Series routers do not support the following policer protocol group options: all-fiber-channel-enode, (however, arp protocol group is supported), bridge-control, diameter, garp-reply, martian-address, proto-802-1x, ptp, pvstp, radius, stp, and tacacs
QFX10002-60C switches do not support the following policer protocol group options: all-fiber-channel-enode, (however, arp protocol group is supported), bridge-control, diameter, garp-reply, martian-address, proto-802-1x, ptp, radius, and tacacs
QFX10002, QFX10008, and QFX10016 switches do not support the ttl protocol group option.

Options

aggregate

Configure parameters for the policer that polices all control packets belonging to the specified protocol as a combined group. An aggregate policer exists for all protocol groups.

Note:

ACX Series routers support only the aggregate policer for the supported protocol groups.

packet-type

Configure policer values for the specified individual control packet type within a protocol group. On some devices, you can configure the packet-type policers in the protocol groups listed in Table 1. For all other protocol groups not listed in Table 1, only aggregate policers are available.

Table 1 lists the protocol groups with packet-type policers available on some devices, and common values for default-configured parameters. Default values can differ among supporting devices and across different Junos OS releases; you can run the show ddos-protection protocols or show ddos-protection protocols parameters CLI command before modifying any configurable values to see the default policer values for all supported protocol groups and packet types. You can also include a specific protocol group and packet type (or aggregate) with those commands.

Each of the protocol groups in Table 1 also supports the aggregate policer. See Table 2 for the default aggregate policer values for all protocol groups.

Table 1: Packet Types Supported by Control Plane DDoS Protection on PTX Series Routers and QFX Series Switches
Protocol Group	Packet Type	Description	Default Bandwidth (pps)	Default Burst (number of packets)	Default Priority
`arp`	`arp-snoop` or `arp` Note: Starting in Junos OS Release 20.3R1 and several other maintenance releases on PTX and QFX Series switches, option name `arp-snoop` is renamed simply `arp`.	ARP traffic	10000	1024 or 2048	High
`arp`	`unclassified`	Unclassified ARP packets	500	1024	High
`bfd`	`bundle-bfd`	(PTX 10003 only) Link bundle BFD traffic	10000	10000	High
	`multihop-bfd`	Multihop BFD traffic	5000 or 10000	2048 or 10000	High
	`unclassified`	Unclassified BFD packets	10000	2048	High
`dhcpv4` (PTX10003 and PTX10008 routers only; for rate-limiting at line card and RE levels)	`ack`	DHCPACK packets	500	500	Medium
	`bad-packets`	DHCPv4 packets with bad formats	0	0	Low
	`bootp`	DHCPBOOTP packets	300	300	Low
	`decline`	DHCPDECLINE packets	500	500	Low
	`discover`	DHCPDISCOVER packets	500	500	Low
	`force-renew`	DHCPFORCERE-NEW packets	2000	2000	High
	`inform`	DHCPINFORM packets	500	500	Low
	`lease-active`	DHCPLEASEACT-IVE packets	2000	2000	High
	`lease-query`	DHCPLEASE-QUERY packets	2000	2000	High
	`lease-unassigned`	DHCPLEASEUN-ASSIGNED packets	2000	2000	High
	`lease-unknown`	DHCPLEASEUN-KNOWN packets	2000	2000	High
	`nak`	DHCPNAK packets	500	500	Low
	`no-message-type`	DHCP packets that are missing the message type	1000	1000	Low
	`offer`	DHCPOFFER packets	1000	1000	Low
	`rebind`	DHCPv4 REBIND packets	2000	2000	High
	`release`	DHCPRELEASE packets	2000	2000	High
	`renew`	DHCPRENEW packets	2000	2000	High
	`request`	DHCPREQUEST packets	1000	1000	Medium
	`unclassified`	All unclassified DHCPv4 packets	300	150	Low
`dhcpv6` (PTX10003 and PTX10008 routers only; for rate-limiting at line card and RE levels)	`advertise`	DHCPv6 ADVERTISE packets	500	500	Low
	`confirm`	DHCPv6 CONFIRM packets	1000	1000	Medium
	`decline`	DHCPv6 DECLINE packets	1000	1000	Low
	`information-request`	DHCPv6 INFORMATION-REQUEST packets	1000	1000	Low
	`leasequery`	DHCPv6 LEASEQUERY packets	1000	1000	Low
	`leasequery-data`	DHCPv6 LEASEQUERY-DATA packets	1000	1000	Low
	`leasequery-done`	LEASEQUERY-DONE packets	1000	1000	Low
	`leasequery-reply`	DHCPv6 LEASEQUERY-REPLY packets	1000	1000	Low
	`rebind`	DHCPv6 REBIND packets	2000	2000	Medium
	`reconfigure`	DHCPv6 RECONFIGURE packets	1000	1000	Low
	`relay-forward`	DHCPv6 RELAY-FORWARD packets	1000	1000	Low
	`relay-reply`	DHCPv6 RELAY-REPLY packets	1000	1000	Low
	`release`	DHCPv6 RELEASE packets	2000	2000	High
	`renew`	DHCPv6 RENEW packets	2000	2000	Medium
	`reply`	DHCPv6 REPLY packets	1000	1000	Medium
	`request`	DHCPv6 REQUEST packets	1000	1000	Medium
	`solicit`	DHCPv6 SOLICIT packets	500	500	Low
	`unclassified`	All unclassified DHCPv6 packets	3000	3000	Low
`eoam`	`oam-cfm`	Ethernet OAM CFM traffic	1000	1024 or 2048	High
`eoam`	`unclassified`	Unclassified Ethernet OAM traffic	100000	1024 or 2048	High
`igmpv6`	`mld`	MLD traffic	1000 or 5000	1024 or 2048	High
`igmpv6`	`unclassified`	Unclassified IGMPv6 packets	1000 or 90000	1024 or 2048	High
`ldp`	`ldp-hello` Some devices have an `ldp-hello` aggregate policer. Only the following devices support this packet type policer: PTX10003 and PTX10008 routers QFX10002, QFX10008, and QFX10016 switches	LDP HELLO traffic	1000	1024	High
`ldp`	`unclassified`	LDP unclassified packets	1000	1024	High
`mcast-snoop`	`igmp`	Control packets for IGMP snooping	500, 5000, or 20000	2048 or 5000	High
	`mld`	Control packets for MLD snooping	500, 2000, or 5000	2048	High
	`pim`	Control packets for PIM snooping	500, 2000, or 5000	2048	High
	`unclassified`	Unclassified multicast snooping control packets	500	2048	High
`radius`	`accounting`	RADIUS accounting packets	200	2048	High
	`authorization`	RADIUS authorization packets	200	2048	High
	`server`	RADIUS server traffic	200	2048	High
	`unclassified`	Unclassified RADIUS traffic	200	2048	High
`tcc`	`ethernet-tcc`	TCC-encapsulated Ethernet traffic	100	100, 1024 or 2048	High
	`iso-tcc`	TCC-encapsulated ISO traffic	100	100, 1024 or 2048	High
	`unclassified`	Unclassified TCC-encapsulated traffic	100	1024 or 2048	High

protocol-group

Configure policer values for the specified protocol group. You can configure the aggregate policer for any of the following protocol groups listed in Table 2. The table shows the aggregate policer default-configured parameters for each protocol group. Default values can differ among supporting devices and across different Junos OS releases; you can run the show ddos-protection protocols or show ddos-protection protocols parameters CLI command before modifying any configurable values to see the default policer values for all supported protocol groups. You can also include a specific protocol group with or without the aggregate option with those commands to see the aggregate policer parameters.

The protocol groups in Table 2 also support any corresponding individual packet-type policers listed in Table 1.

Table 2: Protocol Groups Supported by Control Plane DDoS Protection on ACX Series Routers, PTX Series Routers, and QFX Series Switches
Protocol Group	Description	Default Bandwidth (pps)	Default Burst (number of packets)
Protocol Group	Description	The default bandwidth and burst values varies based on the platform type and underlying DDoS infra settings.
`all-fiber-channel-enode`	Fiber channel ENode traffic	10	1024 or 2048
`arp` or `arp-snoop` (Different platforms support an aggregate policer protocol group option for ARP traffic named either `arp` or `arp-snoop`.)	ARP traffic Note: On some platforms, the `arp` protocol group encompasses `arp-snoop` as a packet type. See Table 1. Starting in Junos OS Release 20.3R1 and other maintenance releases on PTX and QFX Series switches, the `arp-snoop` packet type option in the `arp` protocol group is renamed `arp`.	1000, 2000, or 10000	512, 1024, 2000, or 2048
`bfd`	Single-hop BFD traffic	1000, 6200, 10000, 20000, or 250000	512, 2048 or 20000
`bfdv6`	BFDv6 traffic	512, 3000, 10000, 20000, or 250000	512, 2048 or 20000
`bgp`	BGP traffic	1200, 1500, 3000, 5000, 10000, 20000, or 250000	512, 2048, 4096, or 20000
`bridge-control`	Bridge Control traffic	10	2048
`dhcpv4` (PTX10003 and PTX10008 routers only)	Aggregate for all DHCPv4 traffic (priority Medium) Note: On PTX10003 and PTX10008 routers, use this option for rate-limiting at PFE line card and RE levels. Use aggregate option `dhcpv4v6` for rate-limiting at PFE chip level.	5000	5000
`dhcpv6` (PTX10003 and PTX10008 routers only)	Aggregate for all DHCPv6 traffic (priority Low) Note: On PTX10003 and PTX10008 routers, use this option for rate-limiting at PFE line card and RE levels. Use aggregate option `dhcpv4v6` for rate-limiting at PFE chip level.	5000	5000
`dhcpv4v6`	DHCPv4 and DHCPv6 traffic (limits apply to combined traffic) Note: On PTX10003 and PTX10008 routers, use this aggregate option for rate-limiting at PFE chip level only (priority is Low). Use `dhcpv4` and `dhcpv6` protocol group and individual packet type options for rate-limiting at line card and RE levels.	600 or 5000	512, 2048 or 5000
`diameter`	Diameter and Gx-Plus traffic	200	2048
`dns`	DNS traffic	200	200 or 2048
`dtcp`	DTCP traffic	200	200 or 2048
`egpv6`	EGPv6 traffic	10	10 or 2048
`eoam`	Ethernet OAM traffic Note: On PTX10003 and PTX10008 routers, the aggregate `eoam` protocol group option includes OAM-CFM packets (no `oam-cfm` individual packet type option).	1000, 6200, or 100000	102, 512, 2048, or 10000
`esmc`	ESMC traffic	200	512
`ethernet-tcc`	TCC-encapsulated Ethernet traffic Note: The `tcc` protocol group option encompasses this as a packet type option on some devices.	100	100 or 2048
`exception`	MTU traffic Multicast traffic TTL traffic (QFX10002, QFX10008, and QFX10016 switches only)	100	2048
`ftp`	FTP traffic	500 or 1500	1500 or 2048
`garp-reply`	Gratuitous ARP reply traffic	100	2048
`gre`	GRE traffic	500	500 or 2048
`icmp`	ICMP traffic	500, 1000, or 20000	500, 2048, or 20000
`igmp`	IGMPv4 and IGMPv6 traffic Note: Use this option on PTX Series and QFX10002-60C devices for IGMPv4 traffic only, and `igmpv6` option for IGMPv6 traffic. On PTX10003 and PTX10008 routers, this option encompasses aggregated IGMP and MLD traffic.	1000, 1600, 5000, or 90000	512, 2048 or 5000
`igmpv6`	IGMPv6 traffic	20000 or 90000	2048 or 5000
`ip-options`	IP traffic with IP packet header options	100	100 or 2048
`ipmcast-miss` (ACX Series only)	Unknown IPv4 and IPv6 multicast packets	600	512
`isis`	IS-IS traffic	1000, 1200, 5000, or 20000	512, 2048, 4096, or 20000
`isis-data`	ISIS-Data traffic	5000, 8000, or 10000	4096 or 8000
`isis-hello`	ISIS-Hello traffic	1000, 5000, or 12000	4096 or 12000
`iso-tcc`	TCC-encapsulated ISO traffic Note: The `tcc` protocol group option encompasses this as a packet type option on some devices.	100	100 or 2048
`l2pt`	Layer 2 protocol tunneling traffic	500	2048
`l2tp`	Layer 2 tunneling protocol traffic	500	500 or 2048
`lacp`	LACP traffic	800, 1000, or 2000	512, 300, 2000, or 2048
`ldp`	LDP traffic	1200, 5000, 10000, or 20000	200, 512, 2048, or 20000
`ldp-hello`	LDP hello packets Note: The following devices have an `ldp-hello` packet type policer and do not use this aggregate policer: PTX10003 and PTX10008 routers QFX10002, QFX10008, and QFX10016 switches	1000 or 5000	2048 or 5000
`lldp`	LLDP traffic	100, 800, or 2000	300, 512, 2000, or 2048
`lmp`	LMP traffic	100	100 or 2048
`martian-address`	Martian address	200	20
`mcast-snoop`	Control traffic for multicast snooping	5000, 20000, or 22000	2048, 6000, or 20000
`mld`	MLD traffic Note: The `igmpv6` protocol group option encompasses this as a packet type option on some devices.	1000	2048
`msdp`	MSDP traffic	20000	20000
`multihop-bfd`	Multihop BFD traffic Note: The `bfd` protocol group option encompasses this as a packet type option on some devices.	1500	2048
`ndpv6`	NDPv6 traffic	100, 1000, or 2000	512, 1024, or 2000
`ntp`	NTP traffic	20000	20000
`oam-cfm`	OAM CFM traffic Note: The `eoam` protocol group option encompasses this as a packet type option on some devices. On PTX10003 and PTX10008 routers, the aggregate `eoam` protocol group option includes OAM-CFM packets (no `oam-cfm` individual packet type option).	200	2048
`oam-lfm`	OAM LFM traffic	200, 800, 1000, or 20000	512, 1000, 2048, or 20000
`ospf`	OSPF traffic	1200, 5000, 10000, or 20000	200, 512, 2048, 4096, or 20000
`ospf-hello`	OSPF hello packets	1000, 1500, or 10000	2048, 4096, or 20000
`pim` (ACX Series only)	PIM IPv4 and IPv6 packets	1600	512
`pim-ctrl`	PIM control packets	1000 or 1500	200 or 2048
`pim-data`	PIM data	2000 or 3000	1024 or 2048
`proto-802-1x`	802.1X traffic	200	200 or 2048
`ptp`	PTP traffic	100	2048
`pvstp`	PVSTP traffic	800, 2000, or 20000	512, 2048, or 20000
`radius`	RADIUS traffic	200	2048
`reject`	Packets rejected by a next-hop forwarding decision	100, 200, or 2000	200, 2000, or 2048
`resolve`	Unclassified IPv4 and IPv6 resolve packets sent to the host because of a traffic request resolve action	100, 500, or 5000	100, 2048, or 5000
`rip`	RIP traffic	200, 1200, or 20000	200, 512, 2048, or 20000
`rsvp`	RSVP traffic	1200, 5000, 10000, or 20000	512, 2048, 10000, or 20000
`snmp`	SNMP traffic	1000 or 20000	1024, 2048, or 20000
`ssh`	SSH traffic	5000 or 20000	500, 2048, or 20000
`stp`	STP traffic	800 or 20000	512, 2048, or 20000
`tacacs`	TACACS+ traffic	200	2048
`tcc`	Transitional Cross-connect encapsulated traffic	100 or 200	200, 1024, or 2048
`telnet`	Telnet traffic	5000 or 20000	500, 2048, or 20000
`ttl`	Time to Live packets	100 or 2000	2048
`unclassified`	Traffic that cannot be classified into one of the other available protocol groups	100 or 10000	2048 or 10000
`vrrp`	VRRP traffic	512, 1000, 2000, or 20000	512, 1000, 2048, or 20000
`vxlan`	VXLAN Layer 2 and Layer 3 packets	300	10

Table 3: Protocol Groups Supported by Control Plane DDoS Protection on PTX Series Routers for Junos OS Evolved
Protocol Group	Description
`arp` or	Configure ARP traffic
`bfd`	Configure BFD traffic
`bfdv6`	BFDv6 traffic
`bgp`	Configure BGP traffic
`custom`	Configure CUSTOM traffic
`sample`	Configure Sampling traffic
`dhcpv4`	Configure DHCPv4 traffic
`dhcpv6`	Configure DHCPv6 traffic
`dhcpv4v6`	Configure DHCPv4/v6 traffic
`l2tp`	Configure L2TP traffic.
`ppp`	Configure PPP traffic.
`pppoe`	Configure PPPoE traffic.

Starting in Junos OS Evolved Release 23.1R1, on QFX5220, QFX5130, and QFX5700 Series devices, the default DDoS localnh aggregate bandwidth value is 1500 pps. Earlier to Junos OS Evolved Release 23.1R1, you can configure the bandwidth value using the [set system ddos-protection protocols localnh aggregate bandwidth 1500 burst 200] CLI command. This configuration enables you to prevent LAG interface down time during the heavy local IP traffic.

Starting in Junos OS Release 23.3R1, on QFX Series devices, we've added the ip-option protocol support at the [edit ddos-protection protocols] hierarchy level.

Starting Junos OS Evolved release 23.4R1 supports, DVLAN (single and dual tag) for subscriber services scaling, performance on ACX7100-48L devices that includes:

DHCP (IP-DEMUX lite) & PPPoE subscribers (IPv4, IPV6, and Dual stack) with CoS Lawful Intercept and filter support.
DVLAN (Single and dual tag) with L2TP (LAC) DDOS policers configuration for BBE protocols. Individual BBE protocol and DDOS protocol group configuration is enabled.
Support for protocol groups DHCPv6, L2TP, PPP, and PPPoE
Only the aggregate DDOS protocol group dhcpv4v6 is active.
Subscriber scale qualification with Class of Support (CoS) for Layer 2 Tunneling Protocol (L2TP), L2TP access concentrator (LAC) subscriber interfaces for IPV4, IPV6 and dual stack.
The remaining statements are explained separately. Search for a statement in CLI Explorer or click a linked statement in the Syntax section for details.

Required Privilege Level

admin—To view this statement in the configuration.

admin-control—To add this statement to the configuration.

Release Information

Statement introduced in Junos OS Release 11.2.

ON THIS PAGE

protocols (DDoS) (ACX Series, PTX Series, and QFX Series)

Syntax (ACX Series Routers)

Syntax (PTX Series Routers and QFX Series Switches)

Syntax (PTX Series and ACX7100-48L for Junos OS Evolved)

Hierarchy Level

Description

Options

Required Privilege Level

Release Information

Related Documentation