Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
 

show chassis pic

Syntax

Syntax (TX Matrix and TX Matrix Plus Routers)

Syntax (MX Series Routers and EX Series Switches)

Syntax (PTX Series Packet Transport Router and MX240, MX480, MX960, MX2010, and MX2020 Routers)

Syntax (QFX Series)

Syntax (ACX500, ACX5048, ACX5096, and ACX7509 Routers)

Description

Display status information about the PIC installed in the specified Flexible PIC Concentrator (FPC) and PIC slot.

Options

fpc-slot slot-number

Display information about the PIC in this particular FPC slot:

  • On a TX Matrix router, if you specify the number of the T640 router by using the lcc number option (the recommended method), replace slot-number with a value from 0 through 7. Otherwise, replace slot-number with a value from 0 through 31.

    Likewise, on a TX Matrix Plus router, if you specify the number of the T1600 router by using the lcc number option (the recommended method), replace slot-number with a value from 0 through 7. Otherwise, replace slot-number with a value from 0 through 31. For example, the following commands have the same result:

  • M120 routers only—Replace slot-number with a value from 0 through 5.

  • MX80 routers only—Replace slot-number with a value from 0 through 1.

  • MX104 routers only—Replace slot-number with a value from 0 through 2.

  • MX240 routers only—Replace slot-number with a value from 0 through 2.

  • MX480 routers only—Replace slot-number with a value from 0 through 5.

  • MX960 routers only—Replace slot-number with a value from 0 through 11.

  • MX2010 routers only—Replace slot-number with a value from 0 through 9.

  • MX2020 routers only—Replace slot-number with a value from 0 through 19.

  • MX2008 routers only—Replace slot-number with a value from 0 through 9.

  • MX10003 routers only—Replace slot-number with a value from 0 through 1.

  • Other routers—Replace slot-number with a value from 0  through 7.

  • EX Series switches:

    • EX3200 switches and EX4200 standalone switches—Replace slot-number with 0.

    • EX4200 switches in a Virtual Chassis configuration—Replace slot-number with a value from 0 through 9 (switch’s member ID).

    • EX8208 switches—Replace slot-number with a value from 0 through 7 (line card).

    • EX8216 switches—Replace slot-number with a value from 0 through 15 (line card).

  • QFX Series:

    • QFX3500, QFX3600, QFX5100, and OCX Series standalone switches—Replace slot-number with 0. In the command output, FPC refers to a line card. The FPC number equals the slot number for the line card.

    • QFabric systems—Replace slot-number with any number between 0 and 15. In the command output, FPC refers to a line card. The FPC number equals the slot number for the line card.

all-members

(MX Series routers and EX Series switches only) (Optional) Display PIC information for all member routers in the Virtual Chassis configuration.

interconnect-device name

(QFabric systems only) (Optional) Display PIC information for a specified Interconnect device.

lcc number

(TX Matrix and TX Matrix Plus routers only) (Optional) On a TX Matrix router, display PIC information for a specified T640 router (or line-card chassis) that is connected to the TX Matrix router. On a TX Matrix Plus router, display PIC information for a specified router (line-card chassis) that is connected to the TX Matrix Plus router.

Replace number with the following values depending on the LCC configuration:

  • 0 through 3, when T640 routers are connected to a TX Matrix router in a routing matrix.

  • 0 through 3, when T1600 routers are connected to a TX Matrix Plus router in a routing matrix.

  • 0 through 7, when T1600 routers are connected to a TX Matrix Plus router with 3D SIBs in a routing matrix.

  • 0, 2, 4, or 6, when T4000 routers are connected to a TX Matrix Plus router with 3D SIBs in a routing matrix.

local

(MX Series routers and EX Series switches only) (Optional) Display PIC information for the local Virtual Chassis member.

member member-id

(MX Series routers and EX Series switches only) (Optional) Display PIC information for the specified member of the Virtual Chassis configuration. Replace member-id with a value of 0 or 1.

node-device name

(QFabric systems only) (Optional) Display PIC information for a specified Node device.

pic-slot slot-number

Display information about the PIC in this particular PIC slot. For routers, replace slot-number with a value from 0 through 3. For EX3200 and EX4200 switches, replace slot-number with 0 for built-in network interfaces and 1 for interfaces on uplink modules. For EX8208 and EX8216 switches, replace slot-number with 0. For the QFX3500 standalone switch and the QFabric system, replace slot-number with 0 or 1.

transport

Display PIC information for optical transport network.

Required Privilege Level

view

Output Fields

Table 1 lists the output fields for the show chassis pic command. Output fields are listed in the approximate order in which they appear.

Table 1: show chassis pic Output Fields

Field Name

Field Description

Type

PIC type.

Note:

On the 1-port OC192/STM64 MICs with the SDH framing mode, the type is displayed as MIC-3D-1STM64-XFP and with the SONET framing mode, the type is displayed as MIC-3D-1OC192-XFP. By default, the 1-port OC192/STM64 MICs displays the type as MIC-3D-1OC192-XFP.

Account Layer2 Overhead

(MX Series routers) Indicates whether functionality to count the Layer 2 overhead bytes in the interface statistics at the PIC level is enabled or disabled.

ASIC type

Type of ASIC on the PIC.

State

Status of the PIC. State is displayed only when a PIC is in the slot.

  • Online— PIC is online and running.

  • Offline—PIC is powered down.

  • Empty—No PIC is present.

  • Present—PIC is plugged in. The PIC is not powered on or operational.

  • Onlining—PIC is in the process of going online. PICs and rest of the hardware is initializing.

  • Offlining—PIC is in the process of going offline. PIC and rest of the hardware is being shutdown down to take the offline gracefully.

  • Fault—PIC is in an alarmed state and the PIC is not operational.

PIC version

PIC hardware version.

Uptime

How long the PIC has been online.

Package

(Multiservices interfaces cards only)

The following services package are supported:

Port Number

Port number for the PIC.

Cable Type

Type of cable connected to the port: LH, LX, or SX.

PIC Port Information (MX480 Router 100-Gigabit Ethernet CFP)

Port-level information for the PIC.

  • Port—Port number

  • Cable type—Type of optical transceiver installed.

  • Fiber type—Type of fiber. SM is single-mode.

  • Xcvr vendor—Transceiver vendor name.

  • Xcvr vendor part number—Transceiver vendor part number.

  • Wavelength—Wavelength of the transmitted signal. Uplinks and downlinks are always 1550 nm. There is a separate fiber for each direction

  • Xcvr Firmware—Transceiver firmware version.

PIC Port Information (MX960 Router Bidirectional Optics )

Port-level information for the PIC.

  • Port—Port number

  • Cable type—Type of small form-factor pluggable (SFP) optical transceiver installed. Uplink interfaces display -U. Down link interfaces display -D.

  • Fiber type—Type of fiber. SM is single-mode.

  • Xcvr vendor—Transceiver vendor name.

  • Xcvr vendor part number—Transceiver vendor part number.

    • BX10-10-km bidirectional optics.

    • BX40-40-km bidirectional optics.

    • SFP-LX-40-km SFP optics.

  • Wavelength—Wavelength of the transmitted signal. Uplinks are always 1310 nm. Downlinks are either 1490 nm or 1550 nm.

PIC Port Information (Next-Generation SONET/SDH SFP)

Port-level information for the next-generation SONET/SDH SFP PIC.

  • Port—Port number.

  • Cable type—Type of small form-factor pluggable (SFP) optical transceiver installed.

  • Fiber type—Type of fiber: SM (single-mode) or MM (multimode).

  • Xcvr vendor—Transceiver vendor name.

  • Xcvr vendor part number—Transceiver vendor part number.

  • Wavelength—Wavelength of the transmitted signal. Next-generation SONET/SDH SFPs use 1310 nm.

PIC port information (MX104 router)

Port-level information for the PIC.

  • Port—Port number

  • Cable type—Type of optical transceiver installed.

  • Fiber type—Type of fiber. SM is single-mode.

  • Xcvr vendor—Transceiver vendor name.

  • Xcvr vendor part number—Transceiver vendor part number.

  • Wavelength—Wavelength of the transmitted signal.

  • Xcvr Firmware—Firmware version of the transceiver.

MSA Version

Multi-source Agreements (MSA) specification version that the specified optics is compliant to. Values supported are:

  • SFP+/SFP28—SFF 8472 (Versions 9.3 through 12,3)

  • QSFP+/QSFP28—SFF 8363 (Versions 1.3 through 2.10)

  • QSFP-DD—CMIS (Versions 3.0, 4.0, and 5.0)

Port speed information

Information pertaining to port speed:

  • Port—Port number.

  • PFE—Packet Forwarding Engine slot number.

  • Capable Port Speed—Speed supported by each port.

Multirate Mode

Rate-selectabilty status for the MIC: Enabled or Disabled.

Channelization

Indicates whether channelization is enabled or disabled on the DS3/E3 MIC.

Administrative State

Indicates the administrative state of the PIC. Possible values are: In Service (Default) and Out of Service.

Operational State

Indicates the operational state of the PIC. Possible values are: Normal and Fault.

Sample Output

show chassis pic fpc-slot pic-slot

show chassis pic fpc-slot pic-slot (PIC Offline)

show chassis pic fpc-slot pic-slot (FPC Offline)

show chassis pic fpc-slot pic-slot (FPC Not Present)

show chassis pic fpc-slot pic-slot (PIC Not Present)

show chassis pic fpc-slot 3 pic-slot 0 (M120 Router)

show chassis pic fpc-slot pic-slot (MX150)

show chassis pic pic-slot 0 fpc-slot 1 (MX960 Router with MPC10E-10C-MRATE, MPC10E-15C-MRATE line cards)

show chassis pic fpc-slot pic-slot (MX960 Router with Bidirectional Optics)

show chassis pic fpc-slot pic-slot (MX480 Router with 100-Gigabit Ethernet MIC)

show chassis pic fpc-slot pic-slot (MX240, MX480, MX960 Routers with Application Services Modular Line Card)

show chassis pic fpc-slot pic-slot (MX960 Router with MPC5EQ)

show chassis pic fpc-slot pic-slot (MX960 Router with MPC3E and 100-Gigabit DWDM OTN MIC)

show chassis pic fpc-slot pic-slot (MX10003 Routers)

show chassis pic fpc-slot pic-slot (PTX1000 and PTX10000)

show chassis pic fpc-slot pic-slot (MSA Version)

show chassis pic fpc-slot pic-slot (PTX3000 Router with 5-port 100-Gigabit DWDM OTN PIC)

show chassis pic fpc-slot pic-slot (MX480 Router with MPC4E)

show chassis pic fpc-slot pic-slot (MX480 router with OTN Interface)

show chassis pic fpc-slot pic-slot (MX2010 Router with OTN Interfaces)

show chassis pic fpc-slot pic-slot (MX2010 Router)

show chassis pic fpc-slot pic-slot (MX2020 Router)

show chassis pic fpc-slot pic-slot (MX2020 Router with MPC5EQ and MPC6E)

show chassis pic fpc-slot pic-slot (MX2020 Router with MPC6E and OTN MIC)

show chassis pic fpc-slot pic-slot (MX2020 Router with MPC4E)

show chassis pic fpc-slot pic-slot (MX2010 Router)

show chassis pic fpc-slot pic-slot (T1600 Router with 100-Gigabit Ethernet PIC)

show chassis pic fpc-slot pic-slot lcc (TX Matrix Router)

show chassis pic fpc-slot pic-slot lcc (TX Matrix Plus Router)

show chassis pic fpc-slot pic-slot (Next-Generation SONET/SDH SFP)

show chassis pic fpc-slot pic-slot (12-Port T1/E1)

show chassis pic fpc-slot 0 pic-slot 1 (4x CHOC3 SONET CE SFP)

show chassis pic fpc-slot 0 pic-slot 0 (SONET/SDH OC3/STM1 [Multi-Rate] MIC with SFP)

show chassis pic fpc-slot 3 pic-slot 0 (8-port Channelized SONET/SDH OC3/STM1 [Multi-Rate] MIC with SFP)

show chassis pic fpc-slot 5 pic-slot 0 (4-port Channelized SONET/SDH OC3/STM1 [Multi-Rate] MIC with SFP)

show chassis pic fpc-slot 1 pic-slot 0 (1-port OC192/STM64 MIC with XFP)

show chassis pic fpc-slot 1 pic-slot 2 (8-port DS3/E3 MIC)

show chassis pic fpc-slot pic-slot (OTN)

show chassis pic fpc-slot pic-slot (QFX3500 Switch)

show chassis pic fpc-slot pic-slot (QFX5100 Switches and OCX Series )

show chassis pic interconnect-device fpc-slot pic-slot (QFabric Systems)

show chassis pic node-device fpc-slot pic-slot (QFabric System)

show chassis pic fpc-slot 0 pic-slot 1 (ACX2000 Universal Access Router)

show chassis pic FPC-slot 1 PIC-slot 0 (MX Routers with Media Services Blade [MSB])

show chassis pic FPC slot 1, PIC slot 2 (MX Routers with Media Services Blade [MSB])

show chassis pic transport fpc-slot pic-slot (PTX Series Packet Transport Routers)

show chassis pic transport fpc-slot pic-slot (MX960 Router with MPC3E and 100-Gigabit DWDM OTN MIC)

show chassis pic fpc-slot 0 pic-slot 0 (ACX5096 Router)

show chassis pic fpc-slot 0 pic-slot 0 (ACX5048 Router)

show chassis pic fpc-slot 0 pic-slot 0 (ACX500 Router)

show chassis pic fpc-slot 0 pic-slot 1 (ACX500 Router)

show chassis pic transport fpc-slot pic-slot (PTX Series Packet Transport Routers)

show chassis pic transport fpc-slot pic-slot (MX960 Router with MPC3E and 100-Gigabit DWDM OTN MIC)

show chassis pic fpc-slot 7 pic-slot 1 (MX960 Router MPC10E-15C-MRATE Line Card)

show chassis pic fpc-slot 0 pic-slot 1 (PTX10001-36MR) (400G ZR and 400G ZR-M optics)

show chassis pic fpc-slot 7 pic-slot 0 (ACX7509-FPC-20Y)

show chassis pic fpc-slot 0 pic-slot 0 (ACX7509-FPC-16C)

show chassis pic fpc-slot 0 pic-slot 0 (ACX7509-FPC-4CD)

show chassis pic fpc-slot pic-slot (MX304)

Release Information

Command introduced before Junos OS Release 7.4.

transport option introduced in Junos OS Release 16.1R1 for MX Series Routers.