Core/CM Server CLI Commands

This chapter describes the commands for available for Juniper ATP Appliance Core/CM or vCore servers. These commands are used to configure devices and software, manage security events, and show system information and status.

You must enclose non-alphabet characters in double quotes in CLI commands.

Basic Mode Commands

Use general system commands to configure the appliance, view appliance history, enter other CLI modes, obtain help with CLI syntax, and to exit the CLI session.

The general commands are:

cm
core
diagnosis
exit
help
history
server
wizard

Refer to the respective sections in this guide to review Diagnosis Mode, CM Mode, Collector Mode and Server Mode commands per product device.

Core Mode Commands

exit
help
history
set (core mode)
show (core mode)
updateimage

Server Mode Commands

exit
help
history
ifrestart
ping
reboot
restart
restore
set (server mode)
set appliance-type (server mode)
server
show (server mode)
shutdown
traceroute
upgrade

Diagnosis Mode Commands

capture-start
copy
exit
gssreport
help
history
set (diagnosis mode)
setupcheck
show (diagnosis mode)

CoreCM CLI Commands

capture-start

Table 1: capture-start
Description	Starts packet capture as a means for diagnosing and debugging network traffic and obtaining stats. See Also:[mode];
Product(s) CLI	`All-in-One \| Collector \| Core \| Mac OS X Detection Engine`
Mode(s)	`Diagnosis`
Syntax	capture-start
Parameters	<IP address> <interface_name>
Sub-Commands	None
Example	The following example starts a packet capture process on interface eth1 for a Traffic Collector with IP address 8.8.8.8: hostname # `diagnosis` hostname (diagnosis)# capture-start 8.8.8.8 eth1 Note: Note: Address 8.8.8.8 need not be a Juniper ATP Appliance. It is just a host that the capture filters on.

cm

Table 2: cm
Description	Enters cm (Central Manager) mode. See Also: `basic` [mode];
Product(s) CLI	`All-in-One \| Core`
Mode(s)	Basic
Syntax	cm
Parameters	None
Sub-Commands	exit \| help \| history \| upgrade
Example	The following command example enters cm configuration mode: hostname # `cm` hostname (cm)#

core

Table 3: core
Description	Enters core mode. See Also: `basic` [mode];
Product(s) CLI	`All-in-One \| Collector \| Core \| Mac OS X Detection Engine`
Mode(s)	Basic
Syntax	core
Parameters	None
Sub-Commands	exit, help, history, show, updateimage
Example	The following command example enters core configuration mode: hostname # core hostname (core)#

copy

Table 4: copy
Description	Uses Secure Copy (SCP) to copy and transfer packet capture or traceback (crash) data to a remote location, providing the same authentication and level of security as an SSH transfer. The copy traceback command, upon Customer Support's request, copies the traceback files out of the box to a remote location. See Also:[mode];
Product(s) CLI	`All-in-One \| Collector \| Core-CM \| Mac OSX Engine`
Mode(s)	Diagnosis
Syntax	copy capture <scp source_file_name username@destination_host:destination_folder> \| traceback {<tab> \| ALL} <string URI as user@hostname:path
Parameters	copy capture <scp remote filename_location> copy traceback <ALL \| filename> copy traceback <tab> [tab displays all available crash filenames]
Sub-Commands	None
Example	The following example copies the file "Eth1.txt" from the local host to a remote host: hostname (diagnosis)# copy capture scp captureEth1.txt mailto:admin@remotehost.edu:/some/remote/directory

diagnosis

Table 5: diagnosis
Description	Enters the Diagnosis configuration and status check mode. See Also: collector [mode], server [mode]
Product(s) CLI	`All-in-One \| Collector \| Mac OS X Detection Engine`
Mode(s)	Basic
Syntax	diagnosis
Parameters	None
Sub-Commands	; ; ; ;;;;;;
Example	The following example enters diagnosis configuration and status check mode: hostname # diagnosis hostname (diagnosis)# ?

exit

Table 6: exit
Description	Ends the CLI session.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Basic \| Core \| Collector \| Diagnosis \| Server
Syntax	exit
Parameters	None
Example	The following example ends a command mode or CLI session. JATP# (diagnosis) exit JATP#

gssreport

Table 7: gssreport
Description	Use the gssreport command to submit reports to Juniper Global Security Services (GSS), and to display the status of the current GSS report. See Also:;[mode]
Product(s) CLI	`All-in-One \| Collector \| Mac OS X Detection Engine`
Mode(s)	diagnosis
Syntax	gssreport status \| submit
Parameters	status - displays the status of the current GSS report. submit - submits a report to Juniper ATP Appliance GSS.
Sub-Commands	None
Example	The following examples display the status of a GSS report submission: hostname # `diagnosis` hostname (diagnosis)# gssreport submit Successfully started GSS report hostname (diagnosis)# gssreport status GSS is currently enabled Last 5-minute GSS report at 2015-07-28 10:34:24.414322: successfully submitted Last hourly GSS report at 2015-07-28 10:34:24.468259: successfully submitted Last daily GSS report at 2015-07-28 10:34:28.225512: successfully submitted

help

Table 8: help
Description	Displays information about the CLI help system.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Basic \| Core \| Collector \| Diagnosis \| Server
Syntax	help
Parameters	`None`
Example	The following example shows some of the output of the help command. CONTEXT SENSITIVE HELP [?] - Display context sensitive help. This is either a list of possible command completions with summaries, or the full syntax of the current command. A subsequent repeat of this key, when a command has been resolved, will display a detailed reference. AUTO-COMPLETION The following keys both perform auto-completion for the current command line. If the command prefix is not unique then the bell will ring and a subsequent repeat of the key will display possible completions. [enter] - Auto-completes, syntax-checks then executes a command. If there is a syntax error then offending part of the command line will be highlighted and explained. [tab] - Auto-completes [space] - Auto-completes, or if the command is already resolved inserts a space. If “<cr>” is shown, that means that what you have entered so far is a complete command, and you may press Enter (carriage return) to execute it. Use ? to learn command parameters and option: `JATP (server)#` show f? firewall Show the firewall configuration settings interface `JATP (server)#` show firewall? all Show the current iptables settings whitelist Show the iptables whitelist settings show firewall whitelist? <cr> show firewall whitelist

history

Table 9: history
Description	Displays the current CLI session command line history.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Basic \| Core \| Collector \| Diagnosis \| Server
Syntax	`hi`story
Parameters	None
Example	The following examples returns command line history for the current CLI session. JATP# (core) history

ifrestart

Table 10: ifrestart
Description	Restarts the interface driver and services using the interface.
Product(s) CLI	`All-in-One \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Server
Syntax	ifrestart eth0 \| eth1
Parameters	eth0 Restarts the management network administra interface. eth1 Restarts the monitoring network interface.
Example	The following example restarts the eth0 interface for the management network. <FireEye_name># ifrestart eth0

ping

Table 11: ping

Description

Sends ICMP (Internet Control Message Protocol) echo request packets to a specified host name or IP address to verify that the destination is reachable over the network.

Product(s) CLI

All-in-One | Collector | Core CM | Mac Mini OS X Detection Engine

Mode(s)

Server

Syntax

ping [-c count] [-h hops] [string]

Parameters

`-c`count	Number of echo requests to send. By default, pings ar continuously until you press Ctrl+C.
`-h`hops	Number of next hops between pings (default is 1).
string	IP address, hostname or interface name used to ping device address

Example

The following example sends three echo requests to the device with the IP Address 10.10.10.1

<FireEye_name># ping -c 3 10.10.10.1

PING 10.10.10.1 (10.10.10.1) 56(84) bytes of data.
64 bytes from 10.10.10.1: icmp_req=1 ttl=64 time=0.314 ms
64 bytes from 10.10.10.1: icmp_req=2 ttl=64 time=0.277 ms
64 bytes from v: icmp_req=3 ttl=64 time=0.274 m

--- 10.10.10.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 1999ms
rtt min/avg/max/mdev = 0.274/0.288/0.314/0.022 ms

reboot

Table 12: reboot
Description	Reboots the Juniper ATP Appliance.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Server
Syntax	reboot
Parameters	`None`
Example	The following example reboots the system. hostname# `reboot`

reset-admin-password

Table 13: reset-admin-password
Description	A sudo user named “recovery” uses this command to reset the admin password. This user will not require any password and can only login on a physical device, not using ssh login.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Server
Syntax	recovery
Parameters	exit \| help\| history \| reset-admin-password
Example	The following example resets the admin password. customer login: recovery Note: Since passwords do not sync across devices, you must perform this reset manually on all JATP devices.

restart

Table 14: restart

Description

Restarts Juniper ATP Appliance services.

Product(s) CLI

All-in-One | Collector | Core CM | Mac Mini OS X Detection Engine

Mode(s)

Server

Syntax

Parameters

all	Restarts all Juniper ATP Appliance services.
behaviorengine	Restarts the Behavioral Analysis Engine
cm	Restarts the Central Manager Web UI service.
collector	Restarts the Collector service.
core	Restarts the Core Detection Engine.
correlationengine	Restarts the Correlation Engine.
database	Restarts the Database.
ntpserver	Restarts the NTP server.
sshserver	Restarts the SSH server.
staticengine	Restarts the Static Analysis Engine.
webserver	Restarts the web server.

Example

The following example restarts the Central manager service.

JATP# restart cm

restore

Table 15: restore

Description

Restores the system configuration to the factory default settings. This will only reset the password to default temporarily.

Product(s) CLI

All-in-One | Collector | Core CM | Mac Mini OS X Detection Engine

Mode(s)

server

Syntax

restore [support | firewall {backup | default} | hostname | network]

Allowlist rules rely on normal service shutdown to be backed up. Powering off a VM directly will lose the allowist state as rules cannot be saved in that case.

Parameters

Note:

vCore for AWS does not use the following CLI commands: restore hostname restore network

support	Restores the default support password setting remote login (set during initial installation per l See also (server)# set (server mode)
firewall {backup \| default}	Restores the firewall settings from either the pr backup, or from the default factory settings.
hostname	Restores the system’s hostname to the factory hostname.
network	Restores the IP address and DNS settings to the factory default settings. Warning: This command option removes the current IP address and DNS settings, and reloads the default values for these settings.

Example

The following example restores the system.

JATP# restore

This next example restores the SSH login “support” password to the default

JATP # restore support password
Restore the default support password? (Yes/No)? yes
support password was restored successfully!

set (core mode)

Table 16: set
Description	Resets the Secondary Core UUID, if the virtual core is cloned.
Product(s) CLI	Core/CM (Virtual Core)
Mode(s)	Core (for Virtual Core configurations)
Syntax	set id
Sub-Commands	None
Example	The following example sets the Virtual Core appliance id: hostname # `core` hostname (core) # set id <cr>

server

Table 17: server
Description	Enters the server configuration mode.
Product(s) CLI	`All-in-One \| Collector \| Core/CM \| Mac Mini Mac OS X`
Mode(s)	Basic
Syntax	server
Sub-Commands	;;;;;;;;;; Whitelist rules rely on normal service shutdown to be backed up.Powering off a VM directly will lose the allowlist state as rules cannot be saved in that case.
Example	The following example enters server configuration mode: hostname # server hostname (server) # ?

set system-alert (server mode)

Table 18: set system-alert
Description	Configure the traffic threshold and checking interval for the Collector “monitored traffic” health status. When the monitored traffic of a collector within the checking interval time is lower than the threshold, a system health alert is generated. You can send an email notification of the alert if email notifications of system health events are configured.
Product(s) CLI	`All-in-One \| Core CM`
Mode(s)	Server, See Also:; `set (collector mode)`; `show`
Syntax	set system-alert traffic <integer> time <interval> Note: Note that both "traffic" and "time" parameters are required in order to set the threshold for both the minimum traffic and time.
Parameters	traffic - the minimum traffic (in KB) interval - the checking interval (in minutes)
Example	JATP (server) # set system-alert traffic 100 time 30 This example sets the system alert such that, if the total monitored traffic of a collector within the last 30 minutes dips lower than 100KB, then a system health alert will be generated (and users will receive an email notification of the alert if email notifications are configured for system health events). By default this alert is disabled, and users must set the minimum traffic and interval in order to enable it. Also note that all bytes seen on Ethernet frames are counted in the traffic. The minimum interval for the "set system-alert traffic" time interval command is 10 minutes. If the minimum interval is set to less than 10 minutes, no alerts will be triggered.

set (server mode)

Table 19: set
Description	Configure the system settings.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Server, See Also: ; ;
Syntax	set [autoupdate {on \| off} \| cli timeout secs \| clock \| cm address \| cysupport {enable \| disable} localmode {enable \| disable}\| passphrase string \| dns \| firewall {all <backup \| flush> \| whitelist} \| hostname string \| ip interface {management \| alternate-exhaust}\| ntpserver \| password \| proxy {config \| enabled \| remove} \| timezone string \| uipassword]
Parameters Note: vCore for AWS does not use the following CLI commands: `set ip` `set hostname` [Users cannot set static IP address or change the hostname directly on an EC2 AWS instance] (See columns below)
autoupdate {content \| software} {on \| off} cli secs clock cm address set cysupport {enable \| disable} \| {localmode} dns firewall {all <backup \| flush> \| whitelist <add \| delete \| flush>} hostname string ip interface {management \| alternateexhaust} <dhcp \| address \| netmask \| gateway}	Turn on or off automatic product updates. set autoupdate content on Sets CLI period in seconds (0 indicates no timeout). Sets the current date and time. Sets the IP address of the Central Manager and netmask using slash notation; ex: AAA.BBB.CCC.DD/X Enables remote SSH login “support” account or localmode enable\|/disable. Sets DNS (or enables DHCP for DNS) for the management interface by default if interface is unspecified. Backs up or flushes (clears) all current iptables for a firewall, or adds, deletes or flushes the current iptables allowlist-specific settings for the firewall. The “add” option adds an IP address to the iptables outbound allowlist. # set firewall whitelist add 10.1.1.1 Sets the system’s host name. Sets the IP address, netmask, or default gateway, or enables DHCP for the management or alternate-exhaust interface.
ntpserver passphrase string password	Sets the Network Time Protocol (NTP) server. Sets the device key password; enter a string. Sets a new password for the CLI administrator.
proxy {config <all\|http> \| enable <on\|off> \| remove <all\|http>}	Config, enable/disable, or remove “all” proxy configs, or remove an HTTP-specific proxy server. Tip: Config the proxy for “all” protocols first, and then change HTTP proxy as needed.
timezone string	Sets the timezone for the device.
uipassword	Sets a new admin password for CM Web UI access.
Examples	The following example enables a proxy server. JATP (server)# set proxy enable on

set appliance-type (server mode)

Table 20: set appliance-type

Description

Change the appliance type at any time. For example, change from All-In-One to Core/CM. Note that if you change the appliance type after the initial installation, all data files related to the current type are lost and you must set up the appliance as you would a fresh box.

Product(s) CLI

All-in-One | Core CM | Collector

Mode(s)

server

Syntax

jatp:AIO#(server)# set appliance-type core-cm

Parameters

all-in-one

core-cm

email-collector

traffic-collector

Example

The following example changes the form factor of the appliance from all-in-one (the default) to core-cm:

jatp:AIO#(server)# set appliance-type core-cm 
This will result in the deletion of all data and configurations not relevant to the new form factor.
Proceed? (Yes/No)?  Yes

set (diagnosis mode)

Table 21: set

Description

Sets the logging levels for Juniper ATP Appliance components from diagnosis mode.

setupcheck

Table 22: setupcheck
Description	Checks and reports on basic configuration settings and analysis pipeline setup.
Product(s) CLI	`All-in-One \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	diagnosis
Syntax	setupcheck {all \| report \| basic \| analysis}
Parameters	all Checks both basic settings and analysis pipelin report Shows report of last setupcheck. basic Checks basic configuration settings. analysis Checks the analysis pipeline.
Example	The following example checks all basic configuration settings as well as the analysis pipeline: JATP (diagnosis) # setupcheck all

show (core mode)

Table 23: show

Description

Displays the guest image(s) status or allowlist statistics.

show (diagnosis mode)

Description

Sets the logging levels for Juniper ATP Appliance components from diagnosis mode.

show (server mode)

Table 24: show
Description	Display configurations and status information.
Product(s)CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Server, See Also:
Syntax	show
Parameters (See Tables below)
autoupdate	Show the automatic update setting.
cli timeout	Show the CLI timeout setting.
clock	Show the current date and time.
cm	Show the Central Manager IP address.
controller	Show the driver state for interfaces.
cysupport	Show the remote SSH login support status.
description	Show the server or system description.
devicekey	Show the device key.
devicetype	Show the device type.
dns	Show the DNS servers settings.
eula	Show the End User License Agreement.
firewall [all <\| whitelist]	Show the firewall configuration settings.
hostname	Show the system’s host name.
interface [management \| monitoring \| alternateexhaust]	Show information about the management (administrative) network interface eth0, or the monitoring interface (eth1), or the alternate-exhaust interface (eth2).
See Also: show controller	Show the IP address of the management (administrative) interface eth0.
ip	Results may show both private and public IP addresses if the AWS vCore has a public IP.
name	Show the server name.
ntpserver	Show the Network Time Protocol (NTP) server settings.
proxy	Shows the proxy configuration for the management network. Show system statistics:
See also show (collector mode) for show proxy inside/outside data path	`cpuload` shows average CPU load in the system for running processes in the last 1, 5 and 15 min intervals.
stats [cpuload \| disk \| memory]	`disk` shows the disk space usage in the system. `memory`shows the system memory usage. show stats cpuload (0.06,0.13,0.13)
system-alert	Shows the current set system-alert settings.
timezone {US/Eastern \| US/Central \| US/ Mountain	Show the current timezone; example: set timezone US/Pacific TIP: set timezone <tab> shows options.
uptime	Show how long the system has been running.
uuid	Show the system UUID (universally unique ID).
version	Show Juniper ATP Appliance software and content security versions:
Example	The following example displays information about the CoreCM server device type: CoreCM(server)# show devicetype Device type: cm, core The following example requests data about the alternate-exhaust interface (eth2): CoreCM(server)# show interface alternate-exhaust The following example shows details about the Collector’s monitoring interface (eth1): CoreCM(server)# show interface monitoring Interface: monitoring (eth1) Enabled: Yes Link: Yes IP Address: unknown Mask: unknown MTU: 1500 MAC Address: 90:d6:1f:22:70:g6 Speed: 1000Mb/s Duplex: Full Auto-negotiation: Yes Medium: Copper RX packets: 1869032424 Bytes: 1716560257902 Errors: 0 Overruns: 0 TX packets: 409287 Bytes: 44607401 Errors: 0 Overruns: 0 Traffic rate for the last 5 seconds/1 minute/5 minutes RX bits/sec: 108616/160176/442736 RX packets/sec: 44/46/91 TX bits/sec: 0/112/128 TX packets/sec: 0/0/0

shutdown

Table 25: shutdown
Description	Shuts down the Juniper ATP Appliance server.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Server
Syntax	`shutdown`
Parameters	None
Example	The following example performs a shutdown of the current device. JATP# shutdown

traceroute

Table 26: traceroute

Description

Displays the route packets trace to a host name or an IP address.

Product(s) CLI

All-in-One | Collector | Core CM | Mac Mini OS X Detection Engine

Mode(s)

Server

Syntax

traceroute

Parameters

-h unsigned integer	Specifies the number of hops
string	Names the remote system to be traced.

Example

The following example performs a traceroute of the named device.

JATP# traceroute -h 2 MacMininOSX-Engine

upgrade

Table 27: upgrade

Description

Upgrade Juniper ATP Appliance software for the Core/CM device or vCore, and all connected physical or virtual devices.

Product(s) CLI

All-in-One | Core CM

Mode(s)

Syntax

upgrade <URI as user@hostname:path>

Parameters

<String_URI>

Specifies the software packages to copy .from a remo location for upgrading via the Core.

Example

The following example copies Juniper ATP Appliance software to the Core from a remote location defined by the path provided.

CoreCM(cm)# upgrade admin@remoteHost.edu:some/remote/ directory

updateimage

Table 28: updateimage

Description

Update or correct the guest-image OS profile used by the detection and analysis behavioral engine.

The updateimage command will update the guest images from a USB drive attached to the Juniper ATP Appliance.

Product(s) CLI

All-in-One | Core-CM | Mac Mini OS X Detection Engine

Mode(s)

Core

Syntax

updateimage

Parameters

built-in

Updates the guest-image on the detection Engine.

Example

The following example performs a built-in profile update for the Core detection engine.

JATP (core)# updateimage built-in
Installing image SC-XP-20140617.img...
Previous version of SC-XP-20140617.img exists.
Checking integrity...
Image SC-XP-20140617.img is already installed
Installing image SC-W7-20140521.img...
Previous version of SC-W7-20140521.img exists.
Checking integrity...
Image SC-W7-20140521.img is already installed

wizard

Table 29: wizard
Description	Enters the Configuration Wizard. For Configuration Wizard commands and response, see “Configuration Wizard for the CoreCM Server” in the next section to follow command prompts and recommended responses.
Product(s) CLI	`All-in-One \| Core/CM \| Collector \| Mac Mini Mac OS X`
Mode(s)	Basic
Parameters	wizard
Example	None
	The following command starts the configuration wizard. hostname # wizard

Configuration Wizard for the CoreCM Server

Note:

Enter CTRL-C to exit the Configuration Wizard at any time. If you exit without completing the configuration, you will be prompted again whether to run the Configuration Wizard.

You may also rerun the Configuration Wizard at any time with the CLI command wizard.

Configuration Wizard Prompts

Customer Response Actions

Use DHCP to obtain the IP address and DNS server address for the administrative interface (Yes/No)?

Note:

Only if your DHCP response is no,enter the following information when prompted:

IP address (no CIDR format)
Netmask
Enter a gateway IP address for this management (administrative) interface:
Enter primary DNS server IP address.
Do you have a secondary DNS Server (Yes/No).
Do you want to enter the search domains?
Enter the search domain (separate multiple search domains by space):

Restart the administrative interface (Yes/No)

We strongly discourage the use of DHCP addressing because it changes dynamically. A static IP address is preferred.

Recommended: Respond with no:

Enter an IP address
Enter a netmask using the form 255.255.255.0.
Enter a gateway IP address.
Enter the DNS server IP address
If yes, enter the IP address of the secondary DNS server.
Enter yes if you want DNS lookups to use a specific domain.
Enter search domain(s) separated by spaces; for example: example.com lan.com dom2.com

Enter yes to restart with the new configuration settings applied.

Enter a valid hostname.

Type a hostname when prompted; do not include the domain; for example: juniperatp1

Note:

Only alphanumeric characters and hyphens (in the middle of the hostname) are allowed.

[OPTIONAL]

If the system detects a Secondary Core with an eth3 port, then the alternate CnC exhaust option is displayed:

Use alternate-exhaust for the analysis engine exhaust traffic (Yes/No)?

Enter IP address for the alternate-exhaust (eth2) interface:

Enter netmask for the alternate-exhaust (eth2) interface: (example: 255.255.0.0)

Enter gateway IP Address for the alternateexhaust (eth2) interface: (example:10.6.0.1)

Enter primary DNS server IP Address for the alternate-exhaust (eth2) interface: (example: 8.8.8.8)

Do you have a secondary DNS server for the alternate-exhaust (eth2) interface?

Do you want to enter the search domains for the alternate-exhaust (eth2) interface?

Note:

A complete network interface restart can take more than 60 seconds

Refer to “Configuring an Alternate Analysis Engine Interface” in the Juniper ATP Appliance Operator’s Guide for more information.

Enter yes to configure an alternate eth2 interface.

Enter the IP address for the eth2 interface.

Enter the eth2 netmask.

Enter the gateway IP address.

Enter the primary DNS server IP Address for the alternate-exhaust (eth2) interface.

Enter yes or no to confirm or deny an eth2 secondary DNS server.

Enter yes or no to indicate whether you want to enter search domain.

Regenerate the SSL self-signed certificate (Yes/No)?

Enter yes to create a new SSL certificate for the Juniper ATP Appliance Server Web UI.

If you decline the self-signed certificate by entering no, be prepared to install a certificate authority (CA) certificate.

Enter the following server attributes:

Central Manager (CM) IP Address:

Device Name: (must be unique)

Device Key PassPhrase

Note:

Remember this passphrase and use it for all distributed devices.

Is this a Central Manager device?:

Enter Yes; the system will auto-set IP 127.0.0.1 as the All-in-One IP address.

Enter a connected Juniper ATP Appliance Collector Device Name; this identifies the Collector in the Web UI.

Enter a device Description

Enter a user-defined PassPhrase to be used to authenticate the Core to the Central Manager.

ON THIS PAGE

Core/CM Server CLI Commands

Basic Mode Commands

CM Commands

Core Mode Commands

Server Mode Commands

Diagnosis Mode Commands

CoreCM CLI Commands

capture-start

cm

core

copy

diagnosis

exit

gssreport

help

history

ifrestart

ping

reboot

reset-admin-password

restart

restore

set (core mode)

server

set system-alert (server mode)

set (server mode)

set appliance-type (server mode)

set (diagnosis mode)

setupcheck

show (core mode)

show (diagnosis mode)

show (server mode)

shutdown

traceroute

upgrade

updateimage

wizard

Configuration Wizard for the CoreCM Server

See Also