All-in-One CLI Commands

capture-start

Table 1: capture-start
Description	Starts packet capture as a means for diagnosing and debugging network traffic and obtaining stats. See Also: [mode]; [mode];
Product(s) CLI	`All-in-One \| Collector`
Mode(s)	`Diagnosis`
Syntax	capture-start
Parameters	<interface_name><IP address>
Sub-Commands	None
Example	The following example starts a packet capture process on interface eth1 for a Traffic Collector with IP address 8.8.8.8: hostname # `diagnosis` hostname (diagnosis)# capture-start eth1 8.8.8.8 Note: Note: Address 8.8.8.8 need not be a Juniper ATP Appliance. It is just a host that the capture filters on.

cm

Table 2: cm
Description	Enters cm (Central Manager) mode. See Also: `basic` [mode];
Product(s) CLI	`All-in-One \| Core`
Mode(s)	Basic
Syntax	cm
Parameters	None
Sub-Commands	exit \| help \| history \| upgrade
Example	The following command example enters cm configuration mode: hostname # `cm` hostname (cm)#

collector

Table 3: collector
Description	Enters the Collector configuration mode. See Also: [mode]
Product(s) CLI	`All-in-One \| Collector`
Mode(s)	Basic
Syntax	collector
Parameters	None
Sub-Commands	`;`;;;
Example	The following example enters collector configuration mode: hostname # `collector` hostname (collector)# ?

copy

Table 4: copy
Description	Uses Secure Copy (SCP) to copy and transfer packet capture or traceback (crash) data to a remote location, providing the same authentication and level of security as an SSH transfer. The copy traceback command, upon Customer Support's request, copies the traceback files out of the box to a remote location. See Also: [mode];
Product(s) CLI	`All-in-One \| Collector \| Core-CM \| Mac OSX Engine`
Mode(s)	Diagnosis
Syntax	copy capture <scp source_file_name username@destination_host:destination_folder> \| traceback {<tab> \| ALL} <string URI as user@hostname:path
Parameters	copy capture <scp remote filename_location> copy traceback <ALL \| filename> copy traceback <tab> [tab displays all available crash filenames]
Sub-Commands	None
Example	The following example copies the file "Eth1.txt" from the local host to a remote host: hostname (diagnosis)# copy capture Eth1.txt mailto:admin@remotehost.edu:/some/remote/directory

core

Table 5: core
Description	Enters core mode. See Also: `basic` [mode];
Product(s) CLI	`All-in-One \| Collector \| Core \| Mac OS X Detection Engine`
Mode(s)	Basic
Syntax	core
Parameters	None
Sub-Commands	exit, help, history, show, updateimage
Example	The following command example enters core configuration mode: hostname # `core` hostname (core)#

diagnosis

Table 6: diagnosis
Description	Enters the Diagnosis configuration and status check mode. See Also: collector [mode], server [mode]
Product(s) CLI	`All-in-One \| Collector \| Mac OS X Detection Engine`
Mode(s)	Basic
Syntax	diagnosis
Parameters	None
Sub-Commands	;;;;;;;;;
Example	`The following example enters diagnosis configuration and status check mode:` hostname # `diagnosis` hostname (diagnosis)# ?

exit

Table 7: exit
Description	Ends the CLI session.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Basic \| Core \| Collector \| Diagnosis \| Server
Syntax	exit
Parameters	None
Example	The following example ends a command mode or CLI session. `JATP# (diagnosis) exit` `JATP#` `JATP` (core) exit `JATP#` exit

gssreport

Table 8: gssreport
Description	Use the gssreport command to submit reports to Juniper Global Security Services (GSS), and to display the status of the current GSS report. See Also: ; [mode]
Product(s) CLI	`All-in-One \| Collector \| Mac OS X Detection Engine`
Mode(s)	diagnosis
Syntax	gssreport status \| submit
Parameters	status - displays the status of the current GSS report. submit - submits a report to Juniper ATP Appliance GSS.
Sub-Commands	None
Example	The following examples display the status of a GSS report submission: hostname # `diagnosis` hostname (diagnosis)# gssreport submit Successfully started GSS report hostname (diagnosis)# gssreport status GSS is currently enabled Last 5-minute GSS report at 2015-07-28 10:34:24.414322: successfully submitted Last hourly GSS report at 2015-07-28 10:34:24.468259: successfully submitted Last daily GSS report at 2015-07-28 10:34:28.225512: successfully submitted

help

Table 9: help
Description	Displays information about the CLI help system.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Basic \| Core \| Collector \| Diagnosis \| Server
Syntax	help
Parameters	`None`
Example	The following example shows some of the output of the help command. CONTEXT SENSITIVE HELP [?] - Display context sensitive help. This is either a list of possible command completions with summaries, or the full syntax of the current command. A subsequent repeat of this key, when a command has been resolved, will display a detailed reference. AUTO-COMPLETION The following keys both perform auto-completion for the current command line. If the command prefix is not unique then the bell will ring and a subsequent repeat of the key will display possible completions. [enter] - Auto-completes, syntax-checks then executes a command. If there is a syntax error then offending part of the command line will be highlighted and explained. [tab] - Auto-completes [space] - Auto-completes, or if the command is already resolved inserts a space. If “<cr>” is shown, that means that what you have entered so far is a complete command, and you may press Enter (carriage return) to execute it. Use ? to learn command parameters and option: `JATP (server)#` show f? firewall Show the firewall configuration settings interface `JATP (server)#` show firewall? all Show the current iptables settings whitelist Show the iptables whitelist settings show firewall whitelist? <cr> show firewall whitelist

history

Table 10: history
Description	Displays the current CLI session command line history.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Basic \| Core \| Collector \| Diagnosis \| Server
Syntax	history
Parameters	None
Example	The following examples returns command line history for the current CLI session. `JATP# (core) history`

ifrestart

Table 11: ifrestart

Description

Restarts the interface driver and services using the interface.

Product(s) CLI

All-in-One | Core CM | Mac Mini OS X Detection Engine

Mode(s)

Server

Syntax

ifrestart eth0 | eth1

Parameters

eth0	Restarts the management network administra interface.
eth1	Restarts the monitoring network interface.

Example

The following example restarts the eth0 interface for the management network.

<FireEye_name># ifrestart eth0

ping

Table 12: ping

Description

Sends ICMP (Internet Control Message Protocol) echo request packets to a specified host name or IP address to verify that the destination is reachable over the network.

Product(s) CLI

All-in-One | Collector | Core CM | Mac Mini OS X Detection Engine

Mode(s)

Server

Syntax

ping [-c count] [-h hops] [string]

Parameters

`-c`count	Number of echo requests to send. By default, pings ar continuously until you press Ctrl+C.
`-h`hops	Number of next hops between pings (default is 1).
string	IP address, hostname or interface name used to ping device address

Example

The following example sends three echo requests to the device with the IP Address 10.10.10.1

<FireEye_name># ping -c 3 10.10.10.1

PING 10.10.10.1 (10.10.10.1) 56(84) bytes of data.
64 bytes from 10.10.10.1: icmp_req=1 ttl=64 time=0.314 ms
64 bytes from 10.10.10.1: icmp_req=2 ttl=64 time=0.277 ms
64 bytes from v: icmp_req=3 ttl=64 time=0.274 m

--- 10.10.10.1 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 1999ms
rtt min/avg/max/mdev = 0.274/0.288/0.314/0.022 ms

reboot

Table 13: reboot
Description	Reboots the Juniper ATP Appliance.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Server
Syntax	reboot
Parameters	`None`
Example	The following example reboots the system. hostname# `reboot`

restart

Table 14: restart

Description

Restarts Juniper ATP Appliance services.

Product(s) CLI

All-in-One | Collector | Core CM | Mac Mini OS X Detection Engine

Mode(s)

Server

Syntax

Parameters

all	Restarts all Juniper ATP Appliance services.
behaviorengine	Restarts the Behavioral Analysis Engine
cm	Restarts the Central Manager Web UI service.
collector	Restarts the Collector service.
core	Restarts the Core Detection Engine.
correlationengine	Restarts the Correlation Engine.
database	Restarts the Database.
ntpserver	Restarts the NTP server.
sshserver	Restarts the SSH server.
staticengine	Restarts the Static Analysis Engine.
webserver	Restarts the web server.

Example

The following example restarts the Central manager service.

JATP# restart cm

restore

Table 15: restore

Description

Restores the system configuration to the factory default settings. This will only reset the password to default temporarily.

Product(s) CLI

All-in-One | Collector | Core CM | Mac Mini OS X Detection Engine

Mode(s)

server

Syntax

restore [support | firewall {backup | default} | hostname | network]

Allowlist rules rely on normal service shutdown to be backed up. Powering off a VM directly will lose the allowist state as rules cannot be saved in that case.

Parameters

Note:

vCore for AWS does not use the following CLI commands: restore hostname restore network

support	Restores the default support password setting remote login (set during initial installation per l See also (server)# set (server mode)
firewall {backup \| default}	Restores the firewall settings from either the pr backup, or from the default factory settings.
hostname	Restores the system’s hostname to the factory hostname.
network	Restores the IP address and DNS settings to the factory default settings. Warning: This command option removes the current IP address and DNS settings, and reloads the default values for these settings.

Example

The following example restores the system.

JATP# restore

This next example restores the SSH login “support” password to the default

JATP # restore support password
Restore the default support password? (Yes/No)? yes
support password was restored successfully!

server

Table 16: server
Description	Enters the server configuration mode. See Also:
Product(s) CLI	`All-in-One \| Collector \| Core/CM \| Mac Mini Mac OS X`
Mode(s)	Basic
Syntax	server
Sub-Commands	; ; ; ; ; ; ; ; Whitelist rules rely on normal service shutdown to be backed up.Powering off a VM directly will lose the allowlist state as rules cannot be saved in that case.
Example	The following example enters server configuration mode: hostname # `server` hostname (server) # ?

set honeypot (collector mode)

Table 17: set honeypot
Description	Enables and disables the SSH-Honeypot feature for a Traffic Collector. A honeypot can be deployed within a customer network to detect network activity generated by malware attempting to infect or attack other machines in a local area network. These attempted SSH logins can be used to supplement detection of lateral spread. There are two parameters that can be set for a honeypot: Enable/disable a honeypot Set a Static IP (IP, mask, and gateway) or DHCP of a publicly addressable interface See Also: show honeypot command in
Product(s) CLI	`All-in-One \| Collector`
Mode(s)	collector
Syntax	(collector)# set honeypot ssh-honeypot enable dhcp (collector)# set honeypot ssh-honeypot enable address (IP address) netmask (subnet IP) gateway (IP address) (collector):# set honeypot ssh-honeypot disable
Example	The following example enables the SMB parser for lateral detections: (collector)# set honeypot ssh-honeypot enable address 1.2.3.4 netmask 255.255.0.0 gateway 1.2.3.1 Note: The static IP configuration does not require configuring DNS. Honeypots do not require a DNS server at this time.

set traffic-monitoring (for JATP700 Appliances only) (collector mode)

Table 18: set traffic-monitoring
Description	Sets the traffic monitoring interface on the JATP700
Product(s) CLI	`All-in-One \| Collector`
Mode(s)	collector
Syntax	# set traffic-monitoring-ifc 1gb_ifc Set the traffic monitoring interface to be the 1G interface. # set traffic-monitoring-ifc 10gb_ifc Set the traffic monitoring interface to be the 10G interface. Note: After making an interface type change, the system must be rebooted for the change to take effect.

set traffic-filter (collector mode)

Table 19: set traffic-filter

Description

Sets traffic filter rules to avoid analysis on a set of configured traffic, which cannot be made retroactive; for example: any analysis skipped as a result of the filtering cannot be reversed. This command can be applied to an entire network/subnet/ CIDR range.

set protocols (collector mode)

Table 20: set protocols
Description	Enables and disables the HTTP or SMB parser for a Traffic Collector. See Also: show protocols command in
Product(s) CLI	`All-in-One \| Collector`
Mode(s)	collector
Syntax	(collector)# set protocols {http [on\|off] \| smb [on\|off]}
Example	The following example enables the SMB parser for lateral detections: hostname (collector) set protocols smb on

set proxy (collector mode)

Table 21: set proxy

Description

Sets an Inside or Outside data path proxy from collector mode.

Deploy Traffic Collectors in locations where the monitoring interface is (1) placed “outside” between the proxy and the egress network for customer environments in which the proxy supports XFF (X-Forwarded-For), or (2) [the more typical deployment scenario], the Collector is placed between the proxy and the internal network using FQDN (if available) to identify the threat source for all types of incidents (“inside” proxy). When configured, the Juniper ATP Appliance Traffic Collector will monitor all traffic and correctly identify source and destination hosts for each link in the kill chain wherever the data allows for it.

Note that if the “X-Forwarded-For” header is provided in the HTTP request, detection will identify threat targets when deployed outside of the proxy (customers can choose to disable the XFF feature in the proxy setting, if desired).

See Also: [“set proxy” command for management network]; ;

Note:

The mitigation IP address of a CNC server is not be available for Inside proxy deployments. When a Juniper ATP Appliance is deployed behind a proxy, the Mitigation-> Firewall page in the Juniper ATP Appliance Central Manager Web UI (which typically displays the CNC server IP address to mitigate) will be empty. The destination IP address of any callback is made to the proxy server ip address, so it is not relevant to display the proxy server IP address on the Mitigation->Firewall page.

Product(s) CLI

All-in-One | Collector

Mode(s)

collector

Syntax

set proxy inside {add <proxy IP address> <proxy port> | remove <proxy IP address> <proxy port>

set proxy outside {add <proxy IP address> | remove <proxy IP address>

Parameters

inside	Sets the inside proxy IP addresses
outside	outside Sets the outside proxy IP addresses
add Adds	a proxy configuration.
remove	Removes a proxy configuration.

Example

The following example sets an inside data path proxy:

JATP (collector)# set proxy inside add 10.1.1.1 8080

The following example sets an outside data path proxy:

JATP (collector)# set proxy outside add 10.2.1.1

set (diagnosis mode)

Table 22: set

Description

Sets the logging levels for Juniper ATP Appliance components from diagnosis mode.

set appliance-type (server mode)

Table 23: set appliance-type

Description

Change the appliance type at any time. For example, change from All-In-One to Core/CM. Note that if you change the appliance type after the initial installation, all data files related to the current type are lost and you must set up the appliance as you would a fresh box.

Product(s) CLI

All-in-One | Core CM | Collector

Mode(s)

server

Syntax

jatp:AIO#(server)# set appliance-type core-cm

Parameters

all-in-one

core-cm

email-collector

traffic-collector

Example

The following example changes the form factor of the appliance from all-in-one (the default) to core-cm:

jatp:AIO#(server)# set appliance-type core-cm 
This will result in the deletion of all data and configurations not relevant to the new form factor.
Proceed? (Yes/No)?  Yes

set ip interface (server mode)

Table 24: set ip interface

Description

Sets the management interface (eth0) and/or the alternate-exhaust interface (eth2) for the Juniper ATP Appliance.

Refer to the Operator’s Guide for information about configuring the optional alternate analysis engine eth2 interface option (it moves CnC traffic during analysis engine processing off the enterprise’s eth0 management network).

set (server mode)

Table 25: set
Description	Configure the system settings.
Product(s) CLI	All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine
Mode(s)	Server, See Also:;
Syntax	set [autoupdate {on \| off} \| cli timeout secs \| clock \| cm address \| cysupport {enable \| disable} localmode {enable \| disable}\| passphrase string \| dns \| firewall {all <backup \| flush> \| whitelist} \| hostname string \| ip interface {management \| alternate-exhaust}\| ntpserver \| password \| proxy {config \| enabled \| remove} \| timezone string \| uipassword]
Parameters (Columns below)	Note: vCore for AWS does not use the following CLI commands: set ip set hostname [Users cannot set static IP address or change the hostname directly on an EC2 AWS instance] server mode “set proxy” command is a management network proxy tool; for data path Collector proxy configurations, refer to set proxy (collector mode)
autoupdate {content \| software} {on \| off} cli timeout secs clock cm address set cysupport {enable \| disable} \| {localmode} dns firewall {all <backup \| flush> \| whitelist <add \| delete \| flush>} hostname string ip interface {management \| alternateexhaust} <dhcp \| address \| netmask \| gateway}	Turn on or off automatic product updates. set autoupdate content on Sets CLI timeout period in seconds (0 indicates no timeout). Sets the current date and time. Sets the IP address of the Central Manager and netmask using the slash notation; example: AAA.BBB.CCC.DD/X Enables remote SSH login “support” account or localmode enable\|/disable. Sets DNS (or enables DHCP for DNS) for the management interface by default if interface is unspecified. Backs up or flushes (clears) all current iptables for a firewall, or adds, deletes or flushes the current iptables allowlist-specific settings for the firewall. The “add” option adds an IP address to the iptables outbound allowlist. # set firewall whitelist add 10.1.1.1 Sets the system’s host name. Sets the IP address, netmask, or default gateway, or enables DHCP for the management or alternate-exhaust interface.
ntpserver passphrase string password	Sets the Network Time Protocol (NTP) server. Sets the device key password; enter a string. Sets a new password for the CLI administrator.
proxy {config <all\|http> \| enabled <on\|off> \| remove <all\|http>}	Config, enable/disable, or remove “all” proxy configs, or remove an HTTP-specific proxy server. Tip: Tip: Config the proxy for “all” protocols first, and then change HTTP proxy as needed.
timezone string	Sets the timezone for the device.
uipassword	Sets a new admin password for CM Web UI access.
Example	The following example disables the CLI timeout counter. JATP (server)# `set cli timeout 0` The following example enables support: JATP (server)# `set cysupport enable`

set system-alert (server mode)

Table 26: set system-alert

Description

Configure the traffic threshold and checking interval for the Collector “monitored traffic” health status.

When the monitored traffic of a collector within the checking interval time is lower than the threshold, a system health alert is generated. You can send an email notification of the alert if email notifications of system health events are configured.

Product(s) CLI

All-in-One | Core CM

Mode(s)

Server, See Also:;; show

Syntax

set system-alert traffic <integer> time <interval>

Note:

Note that both "traffic" and "time" parameters are required in order to set the threshold for both the minimum traffic and time.

Parameters

traffic	- the minimum traffic (in KB)
interval	- the checking interval (in minutes)

Example

JATP (server) # set system-alert traffic 100 time 30

This example sets the system alert such that, if the total monitored traffic of a collector within the last 30 minutes dips lower than 100KB, then a system health alert will be generated (and users will receive an email notification of the alert if email notifications are configured for system health events).

By default this alert is disabled, and users must set the minimum traffic and interval in order to enable it. Also note that all bytes seen on Ethernet frames are counted in the traffic.

The minimum interval for the "set system-alert traffic" time interval command is 10 minutes. If the minimum interval is set to less than 10 minutes, no alerts will be triggered.

setupcheck

Table 27: setupcheck

Description

Checks and reports on basic configuration settings and analysis pipeline setup.

Product(s) CLI

All-in-One | Core CM | Mac Mini OS X Detection Engine

Mode(s)

diagnosis

Syntax

setupcheck {all | report | basic | analysis}

Parameters

all	Checks both basic settings and analysis pipelin
report	Shows report of last setupcheck.
basic	Checks basic configuration settings.
analysis	Checks the analysis pipeline.

Example

The following example checks all basic configuration settings as well as the analysis pipeline:

JATP (diagnosis) # setupcheck all

show (collector mode)

Table 28: show (collector mode)

Description

Displays the Traffic Collector HOMENET settings and all configured subnets, as well as current traffic filters and the current XFF status (enabled or disabled)

Product(s) CLI

All-in-One | Collector

Mode(s)

Collector

Subcommands

homenet | traffic-filter | proxy | honeypot

Syntax

show

Parameters

traffic-filter	Shows all traffic filter rules.
protocols	Shows current HTTP or SMB protocol parser settings
proxy {inside\|outside}	Shows Traffic Collector proxy for inside or outside configurations.
honeypot	Shows the current honeypot configuration.

Example

The following example displays the current Collector proxy inside settings:

collector02(collector)# show proxy inside
Proxy IPs: 10.1.1.1

The following example displays the current traffic filter:

collector02 (collector)# show traffic-filter
Name: CustomRule2, Domain: headqtrs.example.com

The following example displays the current SMB protocol parser setting:

collector02 (collector)# show protocols

The following example displays the current honeypot configuration:

collector02 (collector)# show honeypot ssh-honeypot

show (collector mode)

Table 29: show (collector mode)
Description	Display the currently selected traffic monitoring interface.
Product(s) CLI	`All-in-One \| Collector`
Mode(s)	Collector
Syntax	collector02 (collector)#ow traffic-monitoring-ifc-type Display the currently selected traffic monitoring interface

show (core mode)

Description

Displays the guest image(s) status or allowlist statistics.

show (diagnosis mode)

Table 30: show (diagnosis mode)

Description

Sets the logging levels for Juniper ATP Appliance components from diagnosis mode.

shutdown

Table 31: shutdown
Description	Shuts down the Juniper ATP Appliance server.
Product(s) CLI	`All-in-One \| Collector \| Core CM \| Mac Mini OS X Detection Engine`
Mode(s)	Server
Syntax	shutdown
Parameters	`None`
Example	The following example performs a shutdown of the current device. JATP# `shutdown`

traceroute

Table 32: traceroute

Description

Displays the route packets trace to a host name or an IP address.

Product(s) CLI

All-in-One | Collector | Core CM | Mac Mini OS X Detection Engine

Mode(s)

Server | Collector

Syntax

traceroute

Parameters

-h unsigned integer	Specifies the number of hops
string	Names the remote system to be traced.

Example

The following example performs a traceroute of the named device.

JATP# traceroute -h 2 MacMininOSX-Engine

upgrade

Table 33: upgrade

Description

Upgrade Juniper ATP Appliance software for the Core/CM device or vCore, and all connected physical or virtual devices.

Product(s) CLI

All-in-One | Core CM

Mode(s)

Syntax

upgrade <URI as user@hostname:path>

Parameters

<String_URI>

Specifies the software packages to copy .from a remo location for upgrading via the Core.

Example

The following example copies Juniper ATP Appliance software to the Core from a remote location defined by the path provided.

CoreCM(cm)# upgrade admin@remoteHost.edu:some/remote/ directory

updateimage

Table 34: updateimage

Description

Update or correct the guest-image OS profile used by the detection and analysis behavioral engine.

The updateimage command will update the guest images from the Juniper ATP Appliance update servers or a USB drive attached to the Juniper ATP Appliance.

Product(s) CLI

All-in-One | Core-CM | Mac Mini OS X Detection Engine

Mode(s)

Core

Syntax

updateimage

Parameters

built-in

Updates the guest-image on the detection Engine.

Example

The following example performs a built-in profile update for the Core detection engine.

JATP (core)# updateimage built-in
Installing image SC-XP-20150617.img...
Previous version of SC-XP-20150617.img exists.
Checking integrity...
Image SC-XP-20150617.img is already installed
Installing image SC-W7-20150521.img...
Previous version of SC-W7-20150521.img exists.
Checking integrity...
Image SC-W7-20150521.img is already installed

wizard

Table 35: wizard
Description	Enters the Configuration Wizard. For Configuration Wizard commands and response, see “Configuration Wizard for the All-in-One Server” in the next section to follow command prompts and recommended responses.
Product(s) CLI	`All-in-One \| Core/CM \| Collector \| Mac Mini Mac OS X`
Mode(s)	Basic
Syntax	wizard
Parameters	None
Example	The following command starts the configuration wizard. hostname # wizard

Configuration Wizard for the All-in-One Server

Table 36: Configuration Wizard for All-in-One Server
Configuration Wizard Prompts	Customer Response Actions
Use DHCP to obtain the IP address and DNS server address for the administrative interface (Yes/No)? Note: Only if your DHCP response is `no` ,enter the following information when prompted: IP address (no CIDR format) Netmask Enter a gateway IP address for this management (administrative) interface: Enter primary DNS server IP address. Do you have a secondary DNS Server (Yes/No). Do you want to enter the search domains? Enter the search domain (separate multiple search domains by space): Restart the administrative interface (Yes/No)?	We strongly discourage the use of DHCP addressing because it changes dynamically. A static IP address is preferred. Recommended: Respond with `no`: Enter an IP address Enter a netmask using the form 255.255.255.0. Enter a gateway IP address. Enter the DNS server IP address If `yes` enter the IP address of the secondary DNS server. Enter `yes` if you want DNS lookups to use a specific domain. Enter search domain(s) separated by spaces; for example: example.com lan.com dom2.com Enter `yes` to restart with the new configuration settings applied.
Enter a valid hostname.	Type a hostname when prompted; do not include the domain; for example: `JuniperATP1`. Note: Only alphanumeric characters and hyphens (in the middle of the hostname) are allowed.
[OPTIONAL] If the system detects a Secondary Core with an eth2 port, then the alternate CnC exhaust option is displayed: Use alternate-exhaust for the analysis engine exhaust traffic (Yes/No)? Enter IP address for the alternate-exhaust (eth2) interface: Enter netmask for the alternate-exhaust (eth2) interface: (example: 255.255.0.0) Enter gateway IP Address for the alternateexhaust (eth2) interface: (example:10.6.0.1) Enter primary DNS server IP Address for the alternate-exhaust (eth2) interface: (example: 8.8.8.8) Do you have a secondary DNS server for the alternate-exhaust (eth2) interface? Do you want to enter the search domains for the alternate-exhaust (eth2) interface? Note: A complete network interface restart can take more than 60 seconds	Refer to “Configuring an Alternate Analysis Engine Interface” in the Juniper ATP Appliance Operator’s Guide for more information. Enter yes to configure an alternate eth2 interface. Enter the IP address for the eth2 interface. Enter the eth2 netmask. Enter the gateway IP address. Enter the primary DNS server IP Address for the alternate-exhaust (eth2) interface. Enter yes or no to confirm or deny an eth2 secondary DNS server. Enter yes or no to indicate whether you want to enter search domain.
Regenerate the SSL self-signed certificate (Yes/No)?	Enter `yes` to create a new SSL certificate for the Juniper ATP Appliance Server Web UI.

ON THIS PAGE

All-in-One CLI Commands

Basic Mode Commands

CM Commands

Core Mode Commands

Server Mode Commands

Collector Mode Commands

Diagnosis Mode Commands