Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
 

SRX2300 Power System

The SRX2300 is powered by two power supplies for 1 + 1 redundancy. The SRX2300 has hot-removable and hot-insertable power supply units (PSUs). If one PSU fails, you can replace it without powering off or disrupting the device function. The second PSU balances the electrical load without interruption. A fan in each power supply provides cooling.

Note:

We ship the SRX2300 with only one PSU. You can order the second PSU separately if required.

CAUTION:

You must not mix AC and DC power supplies in the same chassis.

AC Power Supply for SRX2300 Firewalls

The following figure shows the AC PSU.

Figure 1: AC Power Supply Unit for SRX2300 AC Power Supply Unit for SRX2300
Table 1: AC Power Supply Unit for SRX2300
Callout Name

1

Power cord retainer

2

PSU handle

3

AC power inlet

4

PSU latch

Table 2: Physical Specifications of the SRX2300 AC PSU
Height Width Depth Weight

1.61 in. (4.1 cm)

2.17 in. (5.5 cm)

14.17 in. (36 cm)

2.14 lb (970 g)

Table 3 describes the AC power specifications for SRX2300.

Table 3: AC Power Specifications for SRX2300
Item Specification
AC input voltage Operating range: 100-127 VAC / 200-240 VAC
AC input line frequency 50–60 Hz
AC input current rating

5.5 A at 100-127 VAC

3 A at 200-240 VAC

Maximum power output 450 W
Table 4: AC Power Consumption for SRX2300
Item Specification
Maximum power consumption 229 W
Average power consumption

186 W

You must use a dedicated external circuit breaker for each power supply. We recommend that use a 16 A (250 VAC) minimum, or as permitted by the local code.

Supported AC Power Cords

Warning:

The AC power cord for the firewall is intended for use with the firewall only and not for any other use.

Note:

In North America, AC power cords must not exceed a length of 4.5 m (approximately 14.75 ft). This length complies with National Electrical code (NEC) Section 400-8 (NFPA 75, 5-2.2) and 210-52, and Canadian Electrical Code (CEC) Section 4-010(3).

Table 5 provides power cord specifications, and Figure 2 depicts the plug on the AC power cord provided for each country or region.

Table 5: AC Power Cord Specifications

Country

Electrical Specification

Plug Standards

Australia

250 VAC, 10 A, 50 Hz

AS/NZ 3112-1993

China

250 VAC, 10 A, 50 Hz

GB2099.1 1996 and GB 1002 1996 (CH1-10P)

Europe (except Italy and United Kingdom)

250 VAC, 10 A, 50 Hz

CEE (7) VII

Italy

250 VAC, 10 A, 50 Hz

CEI 23-16/VII

Japan

125 VAC, 12 A, 50 or 60 Hz

JIS 8303

North America

125 VAC, 10 A, 60 Hz

NEMA 5-15

United Kingdom

250 VAC, 10 A, 50 Hz

BS 1363A

Figure 2: AC Plug Types AC Plug Types
Note:

Power cords and cables must not block access to firewall components or drape where people might trip on the cables.

DC Power Supply for SRX2300 Firewalls

The following figure shows the DC PSU.

Figure 3: DC Power Supply PSU for SRX2300
Table 6: DC Power Supply Unit for SRX2300
Callout Name

1

PSU handle

2

DC power terminals

3

PSU latch

Table 7: Physical Specifications of the SRX2300 DC PSU
Height Width Depth Weight

1.61 in. (4.1 cm)

2.17 in. (5.5 cm)

14.17 in. (36 cm)

2.16 lb (980 g)

Table 8 describes the DC power specifications for SRX2300.

Table 8: DC Power Specifications for SRX2300
Item Specification
DC Input Voltage –44 VDC through –72 VDC
DC input current rating 20 A maximum
Maximum power output 650 W
Table 9: DC Power Consumption for SRX2300
Item Specification
Maximum power consumption 238 W
Average power consumption

194 W

PSU LEDs on SRX2300 Firewalls

The AC PSU has a single bicolor LED that indicates the status. Figure 4 shows the location of the LED on the AC PSU and Table 10 describes it.

Figure 4: LEDs on the AC PSU LEDs on the AC PSU
Table 10: LEDs on the AC PSU
Callout Color State Description
1 Unlit Off No power input.
Green On PSU is operating normally.
Blinking The device is in standby mode.
Amber Blinking PSU is operating under overload.
On The system has detected an error in the PSU. Replace the PSU immediately. To maintain proper airflow thorugh the chassis, leave the PSU installed in the chassis until you are ready to replace it.

Figure 5 shows the location of the LEDs on the DC PSU and Table 11 describes the LEDs.

Figure 5: LEDs on the DC PSU LEDs on the DC PSU
Table 11: LEDs on the DC PSU
Callout Name Color State Description
1 Input Unlit Off No power input.
Green On The PSU is operating normally.
2 Output Unlit Off No power output.
Green On The PSU is operating normally.
3 Fault Amber On The system has detected an error in the PSU. Replace the PSU immediately. To maintain proper airflow thorugh the chassis, leave the PSU installed in the chassis until you are ready to replace it.