Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
 

MX2000 High-Voltage Universal PDM (MX2K-PDM-HV) Power Cord Specifications

Table 1 provides specifications and plug standards for the AC (20-input) power cord applicable to the universal (HVAC/HVDC) PDMs.

Table 1: 20-A Cabling Options

Spare Juniper Model Number

Locale

Cord Set Rating

Connector

CBL-JNP-SG4-C20

North America

AC Power Cord

20 A, 250 VAC

C20 to Anderson 3-5958p4

Table 2 provides specifications and connectors on the 30-A power cord provided for each country or region applicable to the universal (HVAC/HVDC) PDMs.

Table 2: 30-A Cabling Options

Spare Juniper Model Number

Locale

Cord Set Rating

Connector

CBL-PWR2-BARE

See Figure 1.

North America

HVAC/HVDC power cord

30 A, 400 VAC

Anderson/straight to bare wire

CBL-PWR-SG4

North America

HVAC/HVDC power cord

30-A, 400 VAC

SAF-D-GRID 400 right-angle (LH)

CBL-PWR2-L6-30P

See Figure 2.

North America

AC Power Cord

30 A, 400 VAC

Anderson/straight to L6-30P

CBL-PWR2-332P6W-RA

Continental Europe

AC power cord

30-A 250 VAC

Anderson/right-angle to IEC 332P6

CBL-PWR2-332P6W

Continental Europe

AC power cord

30-A 250 VAC

Anderson/right-angle to IEC 332P6

CBL-PWR-SG4-RA

USA

HVAC/HVDC power cord

30-A, 400 VAC

SAF-D-GRID 400 right-angle (LH)

CBL-PWR2-L6-30P-RA

North America

AC power cord

30 A, 250 VAC

Anderson/right-angle to L6-30P

CBL-PWR2-330P6W-RA Figure 3.

Continental Europe

AC power cord

30 A, 250 VAC

Anderson/right-angle to IEC 330P6

CBL-PWR2-330P6W

North America

AC power cord

30 A, 250 VAC

Anderson/right-angle to IEC 330P6

For the HVAC/HVDC power cord one end of the cable has an SAF-D-Grid 400 connector, the other end of the cable is bare wire. See Figure 1 and Table 2. These cables are separately orderable and are not shipped automatically with the MX2K-PDM-HV orders. An example of the bare wire cable and connector is shown in Figure 1.

For connection to AC systems, Juniper provides a cable with either a NEMA 30-A connector (Figure 2).

Figure 1: Bare Cable with Anderson ConnectorBare Cable with Anderson Connector
  1

Black wire–Positive (+)

  3

White wire–Negative

  2

Green wire-Ground

 
Figure 2: NEMA L6-P30 Connector NEMA L6-P30 Connector
Figure 3: IEC 330P6W Connector IEC 330P6W Connector
Warning:

The AC power cord for the router is intended for use with the router only and not for any other use.

Warning:

Translation from Japanese: The attached power cable is only for this product. Do not use the cable for another product.

Note:

In North America, AC power cords must not exceed 4.5 m (approximately 14.75 ft) in length, to comply with National Electrical Code (NEC) Sections 400-8 (NFPA 75, 5-2.2) and 210-52, and Canadian Electrical Code (CEC) Section 4-010(3). You can order AC power cords that are in compliance.

Warning:

The router is a pluggable type A equipment installed in restricted access location. It has a separate protective earthing terminal (Metric [–M6] and English [–¼-20] screw ground lugs) provided on the chassis in addition to the grounding pin of the power supply cord. This separate protective earth terminal must be permanently connected to earth.

CAUTION:

Power cords and cables must not block access to device components or drape where people could trip on them.