Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
ON THIS PAGE
 

JATP400 Site Guidelines and Requirements

General Site Installation Guidelines for the JATP400 Appliance

The following precautions can help you plan an acceptable operating environment for your JATP400 appliance and avoid equipment failures caused by environmental factors:

  • For the cooling system to function properly, the airflow around the chassis must be unrestricted. Allow sufficient clearance between the front and back of the chassis and adjacent equipment. Ensure that there is adequate circulation in the installation location.

  • Follow the electrostatic discharge (ESD) procedures to avoid damaging the equipment. Static discharge can cause either components to fail, completely or intermittently over time.

Note:

Install the appliance only in restricted areas, such as dedicated equipment rooms and equipment closets, in accordance with Articles 110–16, 110–17, and 110–18 of the National Electrical Code, ANSI/NFPA 70.

JATP400 Appliance Physical Specifications

Table 1 lists the hardware specifications for the JATP400 appliance.

Table 1: JATP400 Appliance Physical Specifications

Specification

JATP400

Dimensions (H x W x D)

1.7 in. x 17.2 in. x 25.6 in. (43 x 437 x 650 mm)

Weight

36 lb (16.33 kg)

Fans

Five 40 x 40 x 56 mm 13K - 11K RPM, counter-rotating fans

The air flow direction is front to rear.

Panel Display

  • UID button

  • LEDs: Information, Network activity, Hard drive activity, and Power

  • Reset button

  • Power button

Rack mountable

Four-post

Ports

  • Two RJ-45 10-Gigabit Ethernet LAN ports

  • Two 10-Gigabit Ethernet SFP+ LAN ports

  • Four RJ-45 1-Gigabit Ethernet LAN ports

  • One RJ-45 Dedicated IPMI LAN port

  • Two USB 2.0 ports and 2 USB 3.0 ports (rear)

  • One VGA port

  • One DB-9 COM port

    Note:

    This port is not supported.

Power

500 W AC-DC redundant power supply

650 W DC -DC redundant power supply

Environmental/Compliance specifications

RoHS

RoHS Compliant

Operating temperature

32° F (0° C) to 104° F (40° C)

Non-operating temperature

-40° F (-40° C) to 158° F (70° C)

Operating relative humidity

8% - 90% noncondensing

Non-operating relative humidity

5% - 95% noncondensing

Operating altitude

6500 ft max.

Maximum thermal output

1002.2 BTU/hour

JATP400 Appliance Rack and Clearance Requirements

You can install the JATP400 appliance in a four-post rack.

Table 2 provides the requirements for rack size, clearance, airflow, spacing of mounting brackets and flange holes, and connecting to the building structure.

Table 2: Rack and Clearance Requirements for the JATP400 Appliance

Rack Requirement

Specifications

Size

A 19-in. (48.3 cm) rack as defined in Cabinets, Racks, Panels, and Associated Equipment (document number EIA-310-D) published by the Electronics Industry Association (http://www.eia.org).

Clearance

  • The outer edges of the mounting brackets extend the width of chassis on both sides to 19-in. (48.3 cm).

  • The front of the chassis extends approximately 1.5-in. (3.8 cm) beyond the mounting ears.

Spacing of mounting bracket and flange holes

  • The appliance can be mounted in any rack that provides holes or hole patterns spaced at 1-U [1.75-in. (4.45 cm)] increments.

  • The mounting brackets and front-mount flanges used to attach the chassis to a rack are designed to fasten to holes spaced at rack distances of 1-U (1.75-in.).

  • The mounting holes in the mounting brackets provided with the appliance are spaced 1.25-in. (3.2 cm) apart (top and bottom mounting hole).

Connecting to the building structure

Always secure the rack in which you are installing the JATP400 appliance to the structure of the building. If your geographical area is subject to earthquakes, bolt the rack to the floor. For maximum stability, also secure the rack to ceiling brackets.

Additional Hardware Requirements

We recommend that you install JATP on your LAN to ensure that it can communicate with your following applicable resources:

  • Authentication servers

  • DNS servers

  • Internal webservers through HTTP/HTTPS

  • External websites through HTTP/HTTPS (optional)

  • The Juniper Networks update server through HTTPS

  • network file system (NFS) file servers (optional)

  • client/server applications (optional)

Table 3 lists port information for the JATP400 appliance.

Table 3: Required Ports

Direction

Default Port

TCP/UDP

Description

LAN

Internet

Depends on Configuration

In

22

TCP

SSH command-line management

Yes

No

No

443

TCP

Secure HTTP/HTTPS. Used for connecting Web interface and APIs

Yes

No

No

Out

22

TCP

SSH connection to new managed device

Yes

Yes

No
 

53

TCP, UDP

DNS lookups

Yes

No

No

443

TCP

System security updates from Juniper Networks

Yes

Yes

Yes

123

UDP

NTP time synchronization

Yes

Yes

Yes

514

UDP

SIEM/Syslog CEF server

Yes

No

No

830

TCP

Juniper SRX Firewall

Note:

For Mitigation through SRX Firewall

Yes

Yes

Yes

Related Documentation