Technical Documentation

jnxAtmVpTable

The jnxAtmVpTable extends the atmVplTable defined in RFC 2515, ATM MIB, and contains additional information about ATM virtual paths (VP).

The jnxAtmVpTable, whose object identifier is jnxAtm 3, contains jnxAtmVpEntry. Each jnxAtmVpEntry, whose object ID is jnxAtmVpTable 1, contains the objects listed in Table 1.

Table 1: jnxAtmVpTable

Object

Object ID

Description

jnxAtmVpEntry

jnxAtmVpTable 1

Represents configuration status and statistics information related to an ATM VP.

However, traffic stats are available per VP tunnel only if shaping is configured on the VP. You can use the jnxAtmVpFlags to determine whether shaping is enabled.

Similarly, the values for OAM config and OAM stat objects are invalid (default value: o) if no OAM is configured. You can use the jnxAtmVpFlags to determine whether OAM is configured.

Note: For an ATM-1 VP, the only valid object is jnxAtmVpFlags.

jnxAtmVpFlags

jnxAtmVpEntry 1

Represents the flags associated with the VP. This object uses the following values:

  • 0 active
  • 1 down
  • 2 oamEnabled
  • 3 shapingEnabled
  • 4 passiveOam

jnxAtmVpTotalDownTime

jnxAtmVpEntry 2

Represents the total downtime for the VP since the last reboot of the system.

jnxAtmVpOamPeriod

jnxAtmVpEntry 3

Indicates the frequency at which the OAM F4 cells are transmitted to find out the status of the VP.

This object returns a value of zero if OAM is not enabled for the VP.

jnxAtmVpOamUpCellCount

jnxAtmVpEntry 4

Indicates the minimum number of consecutive loopback cells required to confirm that a VP is up.

jnxAtmVpOamDownCellCount

jnxAtmVpEntry 5

Indicates the minimum number of consecutive loopback cells required to confirm that a VP is down.

jnxAtmVpInBytes

jnxAtmVpEntry 6

Indicates the number of bytes received on the VP.

jnxAtmVpOutBytes

jnxAtmVpEntry 7

Indicates the number of bytes sent out of the VP.

jnxAtmVpInPkts

jnxAtmVpEntry 8

Indicates the number of packets received on the VP.

jnxAtmVpOutPkts

jnxAtmVpEntry 9

Indicates the number of packets sent out on the VP.

jnxAtmVpInOamF4Cells

jnxAtmVpEntry 10

Indicates the number of OAM F4 cells received on the VP.

jnxAtmVpOutOamF4Cells

jnxAtmVpEntry 11

Indicates the number of OAM F4 cells transmitted on the VP.

jnxAtmVpInOamF4LoopCells

jnxAtmVpEntry 12

Indicates the number of OAM F4 loopback cells received on the VP.

jnxAtmVpOutOamF4LoopCells

jnxAtmVpEntry 13

Indicates the number of OAM F4 cells transmitted on the VP.

jnxAtmVpInOamF4RdiCells

jnxAtmVpEntry 14

Indicates the number of OAM F4 RDI cells received on the VP.

jnxAtmVpOutOamF4RdiCells

jnxAtmVpEntry 15

Indicates the number of OAM F4 RDI cells transmitted on the VP.

jnxAtmVpInOamF4AisCells

jnxAtmVpEntry 16

Indicates the number of OAM F4 AIS cells received on the VP.


Published: 2010-04-27