Technical Documentation

Physical Interfaces Properties Statements List

Table 1 lists statements that you can use to configure physical interfaces.

Table 1: Statements for Physical Interface Properties

Statement

Interface Types

Usage Guidelines

Aggregated Ethernet interfaces

Aggregated Ethernet Interfaces Overview

Interfaces with Point-to-Point Protocol (PPP) encapsulation

Configuring the PPP Challenge Handshake Authentication Protocol

All

Configuring Accounting for the Physical Interface

Interfaces with PPP encapsulation

Configuring PPPoE

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

acknowledge-timer milliseconds

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

action-red-differential-delay (disable-tx | remove-link)

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

advertise-interval milliseconds

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

Gigabit Ethernet intelligent queuing (IQ and IQE) interfaces and Gigabit Ethernet interfaces with small form-factor pluggable transceivers (SFPs) (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i router)

Configuring Gigabit Ethernet Policers

Aggregated SONET/SDH interfaces

Configuring Aggregated SONET/SDH Interfaces

Aggregated Ethernet interfaces

Aggregated Ethernet Interfaces Overview

SONET/SDH interfaces

Specifying OC768-over-OC192 Mode

Aggregated SONET/SDH interfaces

Configuring Aggregated SONET/SDH Interfaces

alarmalarm-name(syslog | link-down)

10-Gigabit Ethernet interfaces

Configuring 10-Gigabit Ethernet Link Down Notification for Optics Options Alarm or Warning

annex (annex-a | annex-b)

ATM interfaces on J Series routers

SONET interfaces using annex-b for MSP switching on M320 and M120 Routers

Configuring SHDSL Operating Mode on an ATM Physical Interface

Configuring APS and MSP

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

atm-encapsulation (direct | plcp)

E3 and T3 traffic over Asynchronous Transfer Mode (ATM) interfaces

Configuring E3 and T3 Parameters on ATM Interfaces

ATM1 and ATM2 IQ interfaces

Interface Encapsulations Overview

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

E1, E3, T1, T3 and Fast Ethernet

Configuring ISDN Logical Interface Properties

Gigabit Ethernet and Gigabit Ethernet IQ and IQE PICs with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i router)

Configuring Gigabit Ethernet Policers

bchannel-allocation (ascending | descending)

J Series routers equipped with a Dual-Port Channelized T1/E1 PIM; for Integrated Services Digital Network Primary Rate Interfaces (ISDN PRI)

Allocating B-Channels for Dialout

bert-algorithm algorithm

E3, T1, T3, multichannel DS3, channelized interfaces (DS3, OC12, and STM1), and channelized IQ and IQE interfaces (E1 and DS3)

Interface Diagnostics

E1, E3, T1, T3, and channelized interfaces (DS3, OC3, OC12, and STM1)

Interface Diagnostics

bert-period seconds

E1, E3, T1, T3, and channelized interfaces (DS3, OC12, and STM1)

Interface Diagnostics

T1 interfaces

Configuring the T1 Buildout

E3 and T3 traffic over ATM interfaces

Configuring E3 and T3 Parameters on ATM Interfaces

Gigabit Ethernet and Gigabit Ethernet IQ and IQE PICs with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i router)

Configuring Gigabit Ethernet Policers

byte-encoding (nx56 | nx64)

DS0 and T1 interfaces

Configuring T1 Byte Encoding

bytes [ values

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

cbit-parity | no-cbit-parity

T3 interfaces

Disabling T3 C-Bit Parity Mode

cbr rate

ATM interfaces

Defining the ATM Traffic-Shaping Profile

ATM2 IQ interfaces using ATM Layer 2 circuit cell-relay transport mode

Configuring the Layer 2 Circuit Cell-Relay Cell Maximum

Interfaces with PPP encapsulation

Configuring the PPP Challenge Handshake Authentication Protocol

cisco-interoperability send-lip-remove-link-for-link-reject

link services IQ (lsq) interfaces

JUNOS Services Interfaces Configuration Guide

Gigabit Ethernet IQ interfaces

Configuring Gigabit Ethernet Policers

clocking clock-source

ATM, DS0, E1, E3, SONET/SDH, T1, and T3 interfaces

Configuring the Clock Source

clocking-mode (dce | internal | loop)

Serial interfaces (EIA-530 and V.35)

Configuring the Serial Clocking Mode

Serial interfaces (EIA-530 and V.35)

Configuring the Serial Clocking Mode

E3 and T3 interfaces

Configuring the E3 CSU Compatibility Mode and Configuring the T3 CSU Compatibility Mode

Interfaces with PPP encapsulation

Configuring the PPP Protocol Field Compression

control-polarity (negative | positive)

Serial interfaces (X.21)

Configuring Serial Signal Polarities

control-signal (assert | de-assert | normal)

Serial interfaces (X.21)

Configuring the Serial Signal Handling

Adaptive services, monitoring services, and collector interfaces

Configuring Multiservice Physical Interface Properties

cts (ignore | normal | require)

Serial interfaces (EIA-530 and V.35)

Configuring the Serial Signal Handling

cts-polarity (negative | positive)

Serial interfaces (EIA-530 and V.35)

Configuring Serial Signal Polarities

current margin

ATM interfaces on J Series routers

Configuring SHDSL Operating Mode on an ATM Physical Interface

dcd (ignore | normal | require)

Serial interfaces (EIA-530 and V.35)

Configuring the Serial Signal Handling

dcd-polarity (negative | positive)

Serial interfaces (EIA-530 and V.35)

Configuring Serial Signal Polarities

Interfaces with Frame Relay encapsulation

Configuring the Router as a DCE

Serial interfaces (EIA-530, V.35, and X.21) on J Series routers

Configuring the Serial Signal Handling

Interfaces with Point-to-Point Protocol (PPP) encapsulation

Configuring the PPP Challenge Handshake Authentication Protocol

All

Adding an Interface Description to the Configuration

ISDN interfaces

Configuring ISDN Physical Interface Properties

All

Disabling a Physical Interface and Tracing Operations of an Individual Router Interface

802.1x Port-Based Network Access Control

IEEE 802.1x Port-Based Network Access Control Overview

ATM interfaces

Configuring the ATM OAM F5 Loopback Cell Threshold

drop-timeout milliseconds

Multilink, link services, and voice services interfaces

JUNOS Services Interfaces Configuration Guide

DS0 interfaces

Channelized Interfaces Overview

dsr (ignore | normal | require)

Serial interfaces (EIA-530 and V.35)

Configuring the Serial Signal Handling

dsr-polarity (negative | positive)

Serial interfaces (EIA-530 and V.35)

Configuring Serial Signal Polarities

Serial interfaces (EIA-530, V.35, and X.21) on M Series and T Series routers

Configuring the Serial Signal Handling

dtr signal-handling-option

Serial interfaces (EIA-530 and V.35)

Configuring the Serial Signal Handling

dtr-circuit (balanced | unbalanced)

Serial interfaces (EIA-530 and V.35)

Configuring the Serial DTR Circuit

dtr-polarity (negative | positive)

Serial interfaces (EIA-530 and V.35)

Configuring Serial Signal Polarities

E1 interfaces

E1 Interfaces Overview

E3 interfaces

E3 Interfaces Overview

All interfaces, except loopback and multicast tunnel

Configuring Interface Encapsulation on Physical Interfaces

encoding (nrz | nrzi)

Serial interfaces (EIA-530, V.35, and X.21)

Configuring Serial Line Encoding

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

ES interfaces

JUNOS Services Interfaces Configuration Guide

Gigabit Ethernet and Gigabit Ethernet IQ and IQE PICs with SFPs (except the 10-port Gigabit Ethernet PIC, and the built-in Gigabit Ethernet port on the M7i router)

Configuring Gigabit Ethernet Policers

Gigabit Ethernet and Gigabit Ethernet IQ and IQE PICs with SFPs (except the 10-port Gigabit Ethernet PIC, Aggregated Ethernet with Gigabit Ethernet IQ interfaces, and the built-in Gigabit Ethernet port on the M7i router)

Configuring Gigabit Ethernet Policers, Configuring MAC Address Filtering, and Configuring the Management Ethernet Interface

facility-override facility-name

Adaptive services interfaces

JUNOS Services Interfaces Configuration Guide

Fast Ethernet interfaces

Ethernet Interfaces Overview

fcs (16 | 32)

E1/E3, SONET/SDH, and T1/T3 interfaces

Configuring the E1 Frame Checksum, Configuring the E3 Frame Checksum, Configuring SONET/SDH Physical Interface Properties, Configuring the T1 Frame Checksum, and Configuring the T3 Frame Checksum

feac-loop-respond | no-feac-loop-respond)

T3 interfaces

Configuring the T3 FEAC Response

Aggregated Ethernet, Fast Ethernet, and Gigabit Ethernet interfaces

Configuring Flow Control

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

forwarding-class class-name

ATM2 IQ interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

forwarding-class class-name

Gigabit Ethernet IQ interfaces

Configuring Gigabit Ethernet Policers

Multilink, link services, and voice services interfaces

JUNOS Services Interfaces Configuration Guide

framingframing-type

E1, E3, and T1 interfaces

Configuring E3 and T3 Parameters on ATM Interfaces, Configuring E1 Framing, and Configuring T1 Framing

framing framing-type

10-Gigabit Ethernet interfaces

10-Gigabit Ethernet Framing Overview

framing framing-type

SONET interfaces

Configuring SONET/SDH Physical Interface Properties

Gigabit Ethernet and Tri-Rate Ethernet copper interfaces

Ethernet Interfaces Overview

Ethernet interfaces

Configuring Gratuitous ARP

hello-timer milliseconds

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

hold-time milliseconds

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

hold-time up milliseconds down milliseconds

All interfaces, except aggregated SONET/SDH, generalized routing encapsulation (GRE) tunnel, and IP tunnel

Damping Interface Transitions and Configuring SONET/SDH Physical Interface Properties

host hostname

Adaptive services interfaces

JUNOS Services Interfaces Configuration Guide

ieee802.1p premium [values]

Gigabit Ethernet IQ interfaces

Configuring Gigabit Ethernet Policers

E1, E3, T1, and T3 interfaces

Configuring the E1 Idle Cycle Flag, Configuring the E3 Idle Cycle Flag, Configuring the T1 Idle Cycle Flag, and Configuring the T3 Idle Cycle Flag

Serial interfaces (EIA-530, V.35, and X.21)

Configuring the Serial Signal Handling

ATM interfaces

Configuring Communication with Directly Attached ATM Switches and Routers

Adaptive services interfaces

JUNOS Services Interfaces Configuration Guide

indication (ignore | normal | require)

Serial interfaces (X.21)

Configuring the Serial Signal Handling

indication-polarity (negative | positive)

Serial interfaces (X.21)

Configuring Serial Signal Polarities

8-port, 12-port, and 48-port Fast Ethernet interfaces

Configuring the Ingress Rate Limit

init-command-string initialization-command-string;

For USB ports (umd0) on J4350 and J6350 Services Routers

Specifying a USB Modem Interface on J Series Routers

Gigabit Ethernet IQ interfaces

Configuring Gigabit Ethernet Policers

Channelized IQ and IQE interfaces, ISDN interfaces

Channelized Interfaces Overview and Configuring ISDN Physical Interface Properties

DS0, E1, E3, and T1 interfaces

Configuring E1 Data Inversion, Configuring E3 Data Inversion, and Configuring T1 Data Inversion

ISDN interfaces

Configuring ISDN Logical Interface Properties

keepalives <down-count number <interval seconds> <up-count number>

Aggregated SONET/SDH, DS0, E1, E3, SONET/SDH, T1, and T3 interfaces

Configuring Keepalives

lacp mode

Aggregated Ethernet interfaces

Configuring Aggregated Ethernet LACP

line-encoding (ami | b8zs)

T1 interfaces

Configuring T1 Line Encoding

line-protocol protocol

Serial interfaces (EIA-530, V.35, and X.21)

Configuring the Serial Line Protocol

line-rate line-rate

ATM interfaces on J Series routers

Configuring SHDSL Operating Mode on an ATM Physical Interface

linear-red-profile profile-name

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

linear-red-profiles profile-name

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

AS PIC link services IQ interfaces (lsq)

JUNOS Services Interfaces Configuration Guide

Management Ethernet (fxp0 or em0) and Fast Ethernet interfaces

Configuring the Link Characteristics

Aggregated Ethernet interfaces

Configuring Aggregated Ethernet Link Speed

Aggregated SONET/SDH interfaces

Configuring Aggregated SONET/SDH Interfaces

lmi lmi-options

Interfaces with Frame Relay encapsulation

Configuring Frame Relay Keepalives and JUNOS Services Interfaces Configuration Guide

OAM CFM Ethernet Local Management Interface

Configuring Ethernet Local Management Interface

lmi-type (ansi | itu)

Link services interfaces and interfaces with Frame Relay encapsulation

Configuring Frame Relay Keepalives

Interfaces with PPP encapsulation

Configuring the PPP Challenge Handshake Authentication Protocol

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

log-prefix prefix-number

Adaptive services interfaces

JUNOS Services Interfaces Configuration Guide

(long-buildout | no-long-buildout)

T3 interfaces

Configuring the T3 Line Buildout

(loop-timing | no-loop-timing)

Channelized IQ interfaces

Configuring the Channelized T3 Loop Timing

DS0, E1, E3, T1, T3, SHDSL on ATM and ATM interfaces on J Series routers, and SONET/SDH interfaces

Configuring E1 Loopback Capability, Configuring E3 Loopback Capability, Configuring T1 Loopback Capability, Configuring T3 Loopback Capability, Configuring SHDSL Operating Mode on an ATM Physical Interface, and Configuring SONET/SDH Physical Interface Properties

Ethernet and 10-Gigabit Ethernet interfaces in WAN PHY mode

Configuring Ethernet Loopback Capability

Serial interfaces

Configuring Serial Loopback Capability

Aggregated Ethernet, Fast Ethernet, and Gigabit Ethernet interfaces

Configuring Ethernet Loopback Capability

loss-priority (high | low)

Gigabit Ethernet IQ interfaces

Configuring Gigabit Ethernet Policers

lowest-priority-defect (all-defects | err-xcon | mac-rem-err-xcon | no-defect | rem-err-xcon | xcon)

Configuring IEEE 802.1ag OAM connectivity-fault management

Configuring a Maintenance Endpoint

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

Link services IQ (lsq) interfaces

JUNOS Services Interfaces Configuration Guide

mac mac-address

Management Ethernet interface (fxp0 or em0)

Configuring the MAC Address on the Management Ethernet Interface

Gigabit Ethernet IQ and IQE, Tri-Rate Ethernet copper, and Gigabit Ethernet PICs with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i router)

Configuring Gigabit Ethernet Policers

Management Ethernet (fxp0 or em0) and Fast Ethernet interfaces

Configuring a Consistent Management IP Address

maximum-vcs maximum-vcs

ATM interfaces

Configuring the Maximum Number of ATM1 VCs on a VP

Aggregated Ethernet interfaces

Configuring Multi-Chassis Link Aggregation

Multilink, link services, and voice services interfaces

JUNOS Services Interfaces Configuration Guide

Connectivity Fault Management

Configuring IEEE 802.3ah OAM Link-Fault Management

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

For USB ports (umd0) on J4350 and J6350 Services Routers

Specifying a USB Modem Interface on J Series Routers

10-Gigabit Ethernet interfaces in WAN PHY mode and ATM and SONET/SDH interfaces in passive monitoring mode

Removing MPLS Labels from Incoming Packets, Enabling Passive Monitoring on SONET/SDH Interfaces, and Configuring SONET/SDH Physical Interface Properties

mrru bytes

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

mtu bytes

All interfaces, except management Ethernet (fxp0 or em0), loopback, multilink, and multicast tunnel

Configuring the Media MTU

Ethernet, SONET, aggregated Ethernet, and aggregated SONET interfaces.

Configuring Multicast Statistics Collection on Aggregated Ethernet Interfaces,
Configuring Multicast Statistics Collection on SONET Interfaces,
Configuring Multicast Statistics Collection on Ethernet Interfaces, and
Configuring Multicast Statistics Collection on Aggregated SONET Interfaces

Adaptive services, monitoring services, and collector interfaces

Configuring Multiservice Physical Interface Properties

n391 number

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

n392 number

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

n393 number

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

neighbor address

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

Ethernet interfaces

Configuring Gratuitous ARP

Interfaces with PPP, Frame Relay, or Cisco High-level Data Link Control (HDLC) encapsulation

Configuring Keepalives

Channelized IQ interfaces

Channelized Interfaces Overview

Link Services IQ (LSQ) interfaces

JUNOS Services Interfaces Configuration Guide

ATM interfaces

Configuring the OAM F4 Cell Flows

oam-period (seconds | disable)

ATM interfaces

Defining the ATM OAM F5 Loopback Cell Period

oc-slice oc-slice-range

Channelized OC12 IQ interfaces

Channelized OC12/STM4 IQ and IQE Interfaces Overview

open-timeout seconds

Adaptive services interfaces

JUNOS Services Interfaces Configuration Guide

Gigabit Ethernet dense wavelength-division multiplexing (DWDM) interfaces

10-Gigabit Ethernet DWDM Interface Wavelength Overview

Gigabit Ethernet IQ interfaces

Configuring Gigabit Ethernet Policers

overflow (discard | tag)

(Receive bucket)

All interfaces, except ATM, channelized E1, E1, Fast Ethernet, Gigabit Ethernet, and channelized IQ interfaces

Configuring Receive and Transmit Leaky Bucket Properties and Configuring Receive and Transmit Leaky Bucket Properties on SONET/SDH Interfaces

overflow (discard)

(Transmit bucket)

paired-group group-name

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

partition partition-number

Channelized IQ interfaces

Channelized Interfaces Overview

Interfaces with PPP encapsulation

Configuring the PPP Challenge Handshake Authentication Protocol

SONET/SDH interfaces

Enabling Passive Monitoring on SONET/SDH Interfaces

path-trace trace-string

10-Gigabit Ethernet interfaces in WAN PHY mode and SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties and Configuring SONET/SDH Physical Interface Properties

(payload-scrambler | no-payload-scrambler)

E3, SONET/SDH, and T3 interfaces

Configuring E3 and T3 Parameters on ATM Interfaces, Configuring E3 HDLC Payload Scrambling, Configuring SONET/SDH Physical Interface Properties, and Configuring T3 HDLC Payload Scrambling

periodic interval

Aggregated Ethernet interfaces

Configuring Aggregated Ethernet LACP

IQ interfaces

JUNOS Services Interfaces Configuration Guide

Interfaces with PPP encapsulation

Configuring the PPP Protocol Field Compression

pic-type (atm1 | atm2)

ATM2 IQ interfaces

Configuring the ATM PIC Type

plp1 cells

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

ATM2 IQ interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

policer cos-policer-name

Gigabit Ethernet and Gigabit Ethernet IQ and IQE PICs with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i router)

Configuring Gigabit Ethernet Policers

ATM and SONET/SDH interfaces in passive monitoring mode

Removing MPLS Labels from Incoming Packets and Enabling Passive Monitoring on SONET/SDH Interfaces

Interfaces with PPP encapsulation

Configuring the PPP Challenge Handshake Authentication Protocol

Enhanced Intelligent Queuing (IQE) interfaces (hierarchical policer)

Applying Policers and JUNOS Class of Service Configuration Guide

Gigabit Ethernet IQ interfaces (policer)

Configuring Gigabit Ethernet Policers

Gigabit Ethernet IQ interfaces (output priority map)

Configuring Gigabit Ethernet Policers

primary sp-fpc/pic/port

Redundant interfaces for adaptive services interfaces (rsp-)

JUNOS Services Interfaces Configuration Guide

priority (high | low)

ATM2 IQ interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

priority number

Ethernet protocols (OAM CFM)

Configuring a Maintenance Endpoint

ATM2 IQ interfaces

Configuring ATM Cell-Relay Promiscuous Mode

protect-circuit group-name

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

ATM1 interfaces

Configuring the ATM1 Queue Length

rate percentage

All interfaces, except ATM, channelized E1, E1, Fast Ethernet, Gigabit Ethernet, and channelized IQ

Configuring Receive and Transmit Leaky Bucket Properties and Configuring Receive and Transmit Leaky Bucket Properties on SONET/SDH Interfaces

All interfaces, except ATM, Fast Ethernet, and Gigabit Ethernet

Configuring Receive and Transmit Leaky Bucket Properties

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

Redundant interfaces for adaptive services interfaces (rsp-)

JUNOS Services Interfaces Configuration Guide

T1 interfaces

Configuring the T1 Remote Loopback Response

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

ATM and SONET/SDH interfaces in passive monitoring mode

Removing MPLS Labels from Incoming Packets and Enabling Passive Monitoring on SONET/SDH Interfaces

revert-time seconds

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

rts (assert | de-assert | normal)

Serial interfaces (EIA-530 and V.35)

Configuring the Serial Signal Handling

rts-polarity (negative | positive)

Serial interfaces (EIA-530 and V.35)

Configuring Serial Signal Polarities

rtvbr peak rate sustained rate burst length

ATM interfaces

Defining the ATM Traffic-Shaping Profile

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

schedulers number

Ethernet IQ2 and IQ2-E PICs port interfaces

JUNOS Services Interfaces Configuration Guide

secondary sp-fpc/pic/port

Redundant interfaces for adaptive services interfaces (rsp-)

JUNOS Services Interfaces Configuration Guide

Services interfaces

JUNOS Services Interfaces Configuration Guide

Serial interfaces (EIA-530, V.35, and X.21)

Serial Interfaces Overview

services priority-level

Adaptive services interfaces

JUNOS Services Interfaces Configuration Guide

ATM interfaces on J Series routers

Configuring SHDSL Operating Mode on an ATM Physical Interface

size

All

Tracing Operations of the Interface Process

ATM interfaces

Defining the ATM Traffic-Shaping Profile

Circuit Emulation PICs

Configuring ATM QoS or Shaping

snext margin

ATM interfaces on J Series routers

Configuring SHDSL Operating Mode on an ATM Physical Interface

ATM interfaces on J Series routers

Configuring SHDSL Operating Mode on an ATM Physical Interface

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

Aggregated Ethernet, Fast Ethernet, Tri-Rate Ethernet copper, and Gigabit Ethernet interfaces

Enabling Ethernet MAC Address Filtering

Aggregated Ethernet, Fast Ethernet, Tri-Rate Ethernet copper, Gigabit Ethernet, Gigabit Ethernet IQ and IQE, and Gigabit Ethernet interfaces with SFPs (except the 10-port Gigabit Ethernet PIC and the built-in Gigabit Ethernet port on the M7i router)

Enabling Ethernet MAC Address Filtering

speed (10m | 100m | 1g | auto)

Management Ethernet interface (fxp0 or em0), Tri-Rate Ethernet copper interfaces, and 12-port and 48-port Fast Ethernet interfaces

Configuring the Interface Speed on Ethernet Interfaces

speed (oc3 | oc12 | oc48)

SONET/SDH PICs with SFP

Configuring the Interface Speed

ISDN interfaces

Configuring ISDN Physical Interface Properties and Configuring ISDN Logical Interface Properties

Gigabit Ethernet IQ interfaces

Stacking and Rewriting Gigabit Ethernet VLAN Tags Overview

start-end-flag (filler | shared)

DS0, E1, E3, T1, and T3 interfaces

Configuring E1 Start and End Flags, Configuring the E3 Start and End Flags, Configuring T1 Start and End Flags, and Configuring T3 Start and End Flags

switching-mode (bidirectional | unidirectional)

Unchannelized OC3, OC12, and OC48 SONET/SDH interfaces on T Series routers

Configuring SONET/SDH Physical Interface Properties

Adaptive services interfaces

JUNOS Services Interfaces Configuration Guide

(syslog | no-syslog)

Adaptive services, monitoring services, and collector interfaces

Configuring Multiservice Physical Interface Properties

T1 interfaces

T1 Interfaces Overview

T3 interfaces

T3 Interfaces Overview

ISDN interfaces

Configuring ISDN Physical Interface Properties

t391 seconds

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

t392 number

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

tei-option (first-call | power-up)

ISDN interfaces

Configuring ISDN Physical Interface Properties

threshold bytes

All interfaces, except ATM, channelized E1, E1, Fast Ethernet, Gigabit Ethernet, and channelized IQ

Configuring Receive and Transmit Leaky Bucket Properties and Configuring Receive and Transmit Leaky Bucket Properties on SONET/SDH Interfaces

timeslots time-slot-range

Channelized T1 IQ and channelized E1 IQ interfaces

Channelized Interfaces Overview

tm (ignore | normal | require)

Serial interfaces (EIA-530)

Configuring the Serial Signal Handling

tm-polarity (negative | positive)

Serial interfaces (EIA-530)

Configuring Serial Signal Polarities

All

Tracing Operations of an Individual Router Interface

All

Tracing Operations of the Interface Process

All interfaces, except ATM, Fast Ethernet, Tri-Rate Ethernet copper, and Gigabit Ethernet

Configuring Receive and Transmit Leaky Bucket Properties

Serial interfaces (EIA-530, V.35, and X.21)

Configuring the Serial Clocking Mode

transmit-weight (cells number | percent number)

ATM2 IQ interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

(traps | no-traps)

All

Enabling or Disabling SNMP Notifications on Physical Interfaces

trigger defect ignore | defect hold-time up milliseconds down milliseconds;

10-Gigabit Ethernet interfaces in WAN PHY mode and ATM over SONET/SDH and SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

E3 IQ interfaces

Configuring E3 IQ and IQE Unframed Mode

10-Gigabit Ethernet interfaces on:

  • MX960 4–Port 10–Gigabit Ethernet DPC
  • T Series 10–Gigabit Ethernet IQ2 PIC
  • T Series 10–Gigabit Ethernet IQ2E PIC

Enabling Unidirectional Traffic Flow on Physical Interfaces

vbr peak rate sustained rate burst length

ATM interfaces

Defining the ATM Traffic-Shaping Profile

vc-cos-mode (alternate | strict)

ATM2 interfaces

Configuring ATM2 IQ VC Tunnel CoS Components

Fast Ethernet, Tri-Rate Ethernet copper, and Gigabit Ethernet interfaces

802.1Q VLANs Overview

Fast Ethernet, Tri-Rate Ethernet copper, Gigabit Ethernet, 10-Gigabit Ethernet, and aggregated Ethernet interfaces

Configuring ATM-to-Ethernet Interworking

vpi vpi-identifier

ATM interfaces

Configuring ATM Cell-Relay Promiscuous Mode and Configuring the Maximum Number of ATM1 VCs on a VP

Channelized STM1 interfaces

Configuring Channelized STM1 Interfaces

warningwarning-name(syslog | link-down)

10-Gigabit Ethernet interfaces

Configuring 10-Gigabit Ethernet Link Down Notification for Optics Options Alarm or Warning

Gigabit Ethernet dense wavelength-division multiplexing (DWDM) interfaces

10-Gigabit Ethernet DWDM Interface Wavelength Overview

working-circuit group-name

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties

Link services and voice services interfaces

JUNOS Services Interfaces Configuration Guide

(z0-increment | no-z0-increment)

SONET/SDH interfaces

Configuring SONET/SDH Physical Interface Properties


Published: 2010-04-20