Technical Documentation

Example: Routing Matrix with a TX Matrix Router Configuration

Routing Matrix with a TX Matrix Router Topology

Figure 1 shows Routing Matrix A, a basic routing matrix consisting of a TX Matrix router and two T640 routers. The TX Matrix router is named SCC and the nodes are named LCC0 and LCC2. The routing matrix with a TX Matrix router is acting as a provider edge (PE) router in a Layer 2 circuit network. SONET interface so-1/1/0 in node LCC0 connects to an IP/MPLS core network, and Asynchronous Transfer Mode 2 (ATM2) intelligent queuing (IQ) interface at-17/1/0 in node LCC2 runs Layer 2 circuit trunk mode to connect to an ATM switch. (For more information about Layer 2 see the JUNOS VPNs Configuration Guide.)

Figure 1: Routing Matrix with a TX Matrix Router Topology Diagram

Image g015014.gif

Some key considerations for this configuration are as follows:

  • Treat the routing matrix like a single router and execute all configuration and operational commands on the TX Matrix router SCC.
  • Create configuration groups for each Routing Engine in the routing matrix by using groups re0, re1, lcc0-re0, lcc2-re0, lcc0-re1, and lcc2-re1. In the groups, configure hostnames, default routes, and management interfaces.
  • To configure interfaces, use the routing matrix FPC numbering convention of slots 0 through 31.
  • To enable ATM2 IQ trunk mode and other chassis-based commands, include the lcc lcc-number statement at the [edit chassis] hierarchy level and use the hardware FPC slot numbers 0 through 7 of node LCC2.
  • Configure most other processes as usual, such as routing, class of service (CoS), and firewalls.

TX Matrix Router—SCC

[edit] groups { # You can create special configuration groups in a routing matrix. re0 { # This group corresponds to the master Routing Engine.system { # on the TX Matrix router.host-name scc;backup-router 192.168.17.254;}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.158/21;}}}}} re1 { # This group corresponds to the backup Routing Enginesystem { # on the TX Matrix router.host-name scc1;backup-router 192.168.17.254;}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.168/21;}}}}} lcc0-re0 { # This group corresponds to the master Routing Enginesystem { # on the T640 router LCC0.host-name lcc0;backup-router 192.168.17.254 destination [10.0.0.0/8 192.168.0.0/16];}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.157/21;}}}}} lcc2-re0 { # This group corresponds to the master Routing Enginesystem { # on the T640 router LCC2.host-name lcc2;backup-router 192.168.17.254 destination [10.0.0.0/8 192.168.0.0/16];}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.159/21;}}}}} lcc0-re1 { # This group corresponds to the backup Routing Engine system { # on the T640 router LCC0.host-name lcc0-1;backup-router 192.168.17.254 destination [10.0.0.0/8 192.168.0.0/16];}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.169/21;}}}}} lcc2-re1 { # This group corresponds to the backup Routing Enginesystem { # on the T640 routing node LCC2.host-name lcc2-1;backup-router 192.168.17.254 destination [10.0.0.0/8 192.168.0.0/16];}interfaces {fxp0 {unit 0 {family inet {address 192.168.77.192/21;}}}}}}apply-groups [ re0 re1 lcc0-re1 lcc2-re1 lcc0-re0 lcc2-re0 ];system {syslog {file messages {any any;}}} chassis { # You must apply chassis commands to a specific T640 router. lcc 2 { # Specify the T640 router and the FPC hardware slot of the node. fpc 1 { # This FPC is equivalent to slot 17 in the routing matrix.pic 1 {atm-l2circuit-mode {trunk nni;}}}}}interfaces {so-1/1/0 { # This is a SONET interface at FPC 1, PIC 1, port 0mtu 9192; # on the T640 router LCC0.unit 0 {family inet {address 10.15.1.1/30 {destination 10.15.1.2;}}family iso;family mpls {filter {input filter_1;}}}}at-17/1/0 { # This is an ATM2 IQ interface at FPC 1, PIC 1, port 0encapsulation atm-ccc-cell-relay; # on the T640 router LCC2.atm-options {pic-type atm2;scheduler-maps { # CoS on an ATM2 IQ PIC works the same in a routing matrix.cos1 { # as it does in a standalone T640 router.forwarding-class ubr {priority low;transmit-weight percent 25;}forwarding-class nrtvbr {priority low;transmit-weight percent 25;}forwarding-class rtvbr {priority low;transmit-weight percent 25;}forwarding-class cbr {priority high;transmit-weight percent 25;}}cos2 {forwarding-class ubr {priority low;transmit-weight percent 10;}forwarding-class nrtvbr {priority low;transmit-weight percent 20;}forwarding-class rtvbr {priority low;transmit-weight percent 30;}forwarding-class cbr {priority high;transmit-weight percent 40;}}cos3 {forwarding-class ubr {priority low;transmit-weight percent 40;}forwarding-class nrtvbr {priority low;transmit-weight percent 30;}forwarding-class rtvbr {priority low;transmit-weight percent 20;}forwarding-class cbr {priority high;transmit-weight percent 10;}}}}unit 0 {trunk-id 0;trunk-bandwidth 10m;cell-bundle-size 2;}unit 1 {trunk-id 1;trunk-bandwidth 10m;cell-bundle-size 1;atm-scheduler-map cos1;}unit 2 {trunk-id 2;trunk-bandwidth 10m;cell-bundle-size 2;atm-scheduler-map cos2;}unit 3 {trunk-id 3;trunk-bandwidth 10m;cell-bundle-size 3;atm-scheduler-map cos3;}}lo0 {unit 0 {family inet {address 127.0.0.1/32;address 10.255.77.158/32 {primary;}}family iso {address 47.0005.80ff.f800.0000.0108.0001.0102.5507.0158.00;}family inet6 {address 2001:db8::10:255:77:158/32 {primary;}}}}} protocols { # You can configure protocols in the routing matrix as usual.mpls {interface so-1/1/0.0;}isis {interface so-1/1/0.0;interface lo0.0;}ldp {interface so-1/1/0.0;interface lo0.0;}l2circuit {neighbor 10.255.71.97 {interface at-17/1/0.0 {virtual-circuit-id 100;}interface at-17/1/0.1 {virtual-circuit-id 101;}interface at-17/1/0.2 {virtual-circuit-id 102;}interface at-17/1/0.3 {virtual-circuit-id 103;}}}} class-of-service { # You can configure CoS in the routing matrix as usual.forwarding-classes {queue 0 ubr;queue 1 nrtvbr;queue 2 rtvbr;queue 3 cbr;}traceoptions {flag all;}} firewall { # You can configure firewalls in the routing matrix as usual.family mpls {filter filter_1 {term plp0 {from {exp [ 0 2 4 6 ];}then {count LOW;loss-priority low;}}term plp1 {from {exp [ 1 3 5 7 ];}then {count HIGH;loss-priority high;}}}}}

Verifying Your Work on the Routing Matrix with a TX Matrix Router

To verify proper operation of the routing matrix with a TX Matrix router, use the following commands on the TX Matrix router:

  • show chassis alarms <lcc lcc-number | scc>
  • show chassis craft-interface <lcc lcc-number | scc>
  • show chassis ethernet-switch <lcc lcc-number | scc>
  • show chassis hardware <lcc lcc-number | scc>
  • show chassis fpc <lcc lcc-number>
  • show chassis lccs
  • show chassis location <fpc | interface | lcc lcc-number | scc>
  • show chassis routing-engine <lcc lcc-number | scc>
  • show chassis sibs <lcc lcc-number | scc>
  • show interfaces terse
  • show route summary
  • show system uptime <all-lcc | lcc lcc-number | scc>
  • show version <all-lcc | lcc lcc-number | scc>

In general, when you issue standard operational commands on a TX Matrix router, you receive output from the primary Routing Engines of all components in the routing matrix. To limit the output of information for a specific T640 router within the routing matrix, include the lcc lcc-number option. To display information for the TX Matrix router only, include the scc option. To display information for all T640 routers within the routing matrix (selected commands only), include the all-lcc option. Any exceptions to this general rule are mentioned next to the appropriate commands.

The following sections show the output of select operational commands used with the configuration example:

Displaying the Software Version on A Routing Matrix with a TX Matrix Router

The show version command provides an excellent example of how you can select output for various components of the routing matrix with a TX Matrix router. If the TX Matrix router (SCC) or a T640 router (LCC) is not specified in the command, then the command displays output for all components.


user@router> show version ?
Possible completions:
  <[Enter]>            Execute this command
  all-lcc              Show software version on all LCC chassis
  brief                Display brief output
  detail               Display detailed output
  lcc                  Show software version on specific LCC (0..3)
  scc                  Show software version on the SCC
  |                    Pipe through a command

 

To display the software version for all routing matrix components, issue the show version command on the TX Matrix router:


user@router> show version
scc-re0:
--------------------------------------------------------------------------
Hostname: scc
Model: TX Matrix
JUNOS Base OS boot [7.0-20040630.0]
JUNOS Base OS Software Suite [7.0-20040629.0]
JUNOS Kernel Software Suite [7.0-20040630.0]
JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0]
JUNOS Routing Software Suite [7.0-20040630.0]
JUNOS Online Documentation [7.0-20040630.0]
JUNOS Crypto Software Suite [7.0-20040630.0]
lcc0-re0:
--------------------------------------------------------------------------
Hostname: lcc0
Model: t640
JUNOS Base OS boot [7.0-20040630.0]
JUNOS Base OS Software Suite [7.0-20040629.0]
JUNOS Kernel Software Suite [7.0-20040630.0]
JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0]
JUNOS Routing Software Suite [7.0-20040630.0]
JUNOS Online Documentation [7.0-20040630.0]
JUNOS Crypto Software Suite [7.0-20040630.0]
JUNOS Support Tools Package [7.0-20040630.0]
lcc2-re0:
--------------------------------------------------------------------------
Hostname: lcc2
Model: t640
JUNOS Base OS boot [7.0-20040630.0]
JUNOS Base OS Software Suite [7.0-20040629.0]
JUNOS Kernel Software Suite [7.0-20040630.0]
JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0]
JUNOS Routing Software Suite [7.0-20040630.0]
JUNOS Online Documentation [7.0-20040630.0]
JUNOS Crypto Software Suite [7.0-20040630.0]
JUNOS Support Tools Package [7.0-20040630.0]

 

To display the software version for the TX Matrix router only, include the scc option:


user@router> show version scc
Hostname: scc
Model: TX Matrix
JUNOS Base OS boot [7.0-20040630.0]
JUNOS Base OS Software Suite [7.0-20040629.0]
JUNOS Kernel Software Suite [7.0-20040630.0]
JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0]
JUNOS Routing Software Suite [7.0-20040630.0]
JUNOS Online Documentation [7.0-20040630.0]
JUNOS Crypto Software Suite [7.0-20040630.0]

To display the software version for a specific T640 router, include the lcc option:


user@router> show version lcc 0
lcc0-re0:
--------------------------------------------------------------------------
Hostname: lcc0
Model: t640
JUNOS Base OS boot [7.0-20040630.0]
JUNOS Base OS Software Suite [7.0-20040629.0]
JUNOS Kernel Software Suite [7.0-20040630.0]
JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0]
JUNOS Routing Software Suite [7.0-20040630.0]
JUNOS Online Documentation [7.0-20040630.0]
JUNOS Crypto Software Suite [7.0-20040630.0]
JUNOS Support Tools Package [7.0-20040630.0]

To display the output for all T640 routers, include the all-lcc option:


user@router> show version all-lcc
lcc0-re0:
--------------------------------------------------------------------------
Hostname: lcc0
Model: t640
JUNOS Base OS boot [7.0-20040630.0]
JUNOS Base OS Software Suite [7.0-20040629.0]
JUNOS Kernel Software Suite [7.0-20040630.0]
JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0]
JUNOS Routing Software Suite [7.0-20040630.0]
JUNOS Online Documentation [7.0-20040630.0]
JUNOS Crypto Software Suite [7.0-20040630.0]
JUNOS Support Tools Package [7.0-20040630.0]
lcc2-re0:
--------------------------------------------------------------------------
Hostname: lcc2
Model: t640
JUNOS Base OS boot [7.0-20040630.0]
JUNOS Base OS Software Suite [7.0-20040629.0]
JUNOS Kernel Software Suite [7.0-20040630.0]
JUNOS Packet Forwarding Engine Support (T-Series) [7.0-20040630.0]
JUNOS Routing Software Suite [7.0-20040630.0]
JUNOS Online Documentation [7.0-20040630.0]
JUNOS Crypto Software Suite [7.0-20040630.0]
JUNOS Support Tools Package [7.0-20040630.0]

Displaying Interfaces

Although individual FPCs are installed in each of the T640 routers, the routing matrix is designed to collect interface information centrally at the TX Matrix router. To display available interfaces in the routing matrix, issue a show interfaces command on the TX Matrix router:


user@router> show interfaces terse
Interface               Admin Link Proto Local                 Remote
so-1/0/0                up    up
so-1/1/0                up    up
so-1/1/0.0              up    up   inet  10.15.1.1           --> 10.15.1.2
                                   iso
                                   mpls
so-1/3/0                up    down
at-2/1/0                up    up
ge-2/2/0                up    up
so-3/3/0                up    up
so-3/3/1                up    up
so-3/3/2                up    down
so-3/3/3                up    down
so-16/0/0               up    down
so-16/0/1               up    down
so-16/0/2               up    down
so-16/0/3               up    up
ge-16/1/0               up    down
so-17/0/0               up    down
at-17/1/0               up    up
at-17/1/0.0             up    up   ccc
at-17/1/0.1             up    up   ccc
at-17/1/0.2             up    up   ccc
at-17/1/0.3             up    up   ccc
at-17/1/1               up    up
ge-17/2/0               up    up
ge-17/2/1               up    up
so-17/3/0               up    down
so-19/0/0               up    down
so-19/1/0               up    down
so-19/2/0               up    down
so-19/3/0               up    down
bcm0                    up    up
bcm0.0                  up    up   tnp   4
dsc                     up    up
em0                     up    up
em0.0                   up    up   tnp   4
fxp0                    up    up
fxp0.0                  up    up   inet  192.168.77.158/21
gre                     up    up
ipip                    up    up
lo0                     up    up
lo0.0                   up    up   inet  10.255.70.158       --> 0/0
                                         127.0.0.1           --> 0/0
                                   iso   47.0005.80ff.f800.0000.0108.0001.0102.5507.0158.00
                                   inet6 2001:db8::10:255:70:158
                                         fe80::280:42ff:fe13:269d
lo0.16385               up    up   inet
                                   inet6 fe80::280:42ff:fe13:269d
lsi                     up    up
mtun                    up    up
pimd                    up    up
pime                    up    up
tap                     up    up

Displaying Routes

When you need to verify route information for a routing matrix, you must issue operational commands on the TX Matrix router. To display available routes for the routing matrix, issue a show route command:


user@router> show route summary
Router ID: 10.255.77.158
inet.0: 13 destinations, 14 routes (12 active, 0 holddown, 1 hidden)
              Direct:      4 routes,      3 active
               Local:      2 routes,      2 active
              Static:      6 routes,      6 active
               IS-IS:      2 routes,      1 active
inet.3: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden)
                 LDP:      1 routes,      1 active
iso.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden)
              Direct:      1 routes,      1 active
mpls.0: 7 destinations, 7 routes (7 active, 0 holddown, 0 hidden)
                MPLS:      3 routes,      3 active
                 LDP:      2 routes,      2 active
               L2CKT:      2 routes,      2 active
inet6.0: 2 destinations, 2 routes (2 active, 0 holddown, 0 hidden)
              Direct:      2 routes,      2 active
__juniper_private1__.inet6.0: 1 destinations, 1 routes (1 active, 0 holddown, 0 hidden)
              Direct:      1 routes,      1 active
l2circuit.0: 5 destinations, 5 routes (5 active, 0 holddown, 0 hidden)
                 LDP:      1 routes,      1 active
               L2CKT:      4 routes,      4 active

Displaying Alarms and System Uptime

To display alarms for all routing matrix components, issue the show chassis alarms command:


user@router> show chassis alarms
scc-re0:
--------------------------------------------------------------------------
2 alarms currently active
Alarm time               Class  Description
2004-09-27 08:50:57 PDT  Major  LCC 2 Major Errors
2004-09-27 08:50:42 PDT  Minor  LCC 0 Minor Errors
lcc0-re0:
--------------------------------------------------------------------------
1 alarms currently active
Alarm time               Class  Description
2004-09-27 08:50:42 PDT  Minor  PEM 1 Absent
lcc2-re0:
--------------------------------------------------------------------------
1 alarms currently active
Alarm time               Class  Description
2004-09-27 08:50:57 PDT  Major  PEM 1 Not OK

To display the craft interface display for all routing matrix components, issue the show chassis craft-interface command:


user@router> show chassis craft-interface
scc-re0:
--------------------------------------------------------------------------
FPM Display contents:
    +--------------------+
    |scc           |
    |2 Alarms active     |
    |R: LCC 2 Major Error|
    |Y: LCC 0 Minor Error|
    +--------------------|
Front Panel System LEDs:
Routing Engine    0    1
--------------------------
OK                *    *
Fail              .    .
Master            *    .
Front Panel Alarm Indicators:
-----------------------------
Red LED      *
Yellow LED   *
Major relay  *
Minor relay  *
CB LEDs:
  CB   0   1
--------------
Amber  .   .
Green  *   *
Blue   *   .
SIB LEDs:
  SIB  0   1   2   3   4
--------------------------
Fail   .   .   .   .   .
OK     *   *   *   *   *
Active .   *   *   *   *
lcc0-re0:
--------------------------------------------------------------------------
FPM Display contents:
    +--------------------+
    |lcc0            |
    |1 Alarm active      |
    |Y: PEM 1 Absent     |
    |                    |
    +--------------------|
Front Panel System LEDs:
Routing Engine    0    1
--------------------------
OK                *    *
Fail              .    .
Master            *    .
Front Panel Alarm Indicators:
-----------------------------
Red LED      .
Yellow LED   *
Major relay  .
Minor relay  *
Front Panel FPC LEDs:
FPC    0   1   2   3   4   5   6   7
------------------------------------
Red    .   .   .   .   .   .   .   .
Green  .   *   *   *   .   .   .   .
CB LEDs:
  CB   0   1
--------------
Amber  .   .
Green  *   *
Blue   *   .
SCG LEDs:
  SCG  0   1
--------------
Amber  .   .
Green  *   *
Blue   *   .
SIB LEDs:
  SIB  0   1   2   3   4
--------------------------
Red    .   .   .   .   .
Green  *   *   *   *   *
lcc2-re0:
--------------------------------------------------------------------------
FPM Display contents:
    +--------------------+
    |lcc2          |
    |1 Alarm active      |
    |R: PEM 1 Not OK     |
    |                    |
    +--------------------|
                    
Front Panel System LEDs:
Routing Engine    0    1
--------------------------
OK                *    *
Fail              .    .
Master            *    .
Front Panel Alarm Indicators:
-----------------------------
Red LED      *
Yellow LED   .
Major relay  *
Minor relay  .
Front Panel FPC LEDs:
FPC    0   1   2   3   4   5   6   7
------------------------------------
Red    .   .   .   .   .   .   .   .
Green  *   *   .   *   .   .   .   .
CB LEDs:
  CB   0   1
--------------
Amber  .   .
Green  *   *
Blue   *   .
SCG LEDs:
  SCG  0   1
--------------
Amber  .   .
Green  *   .
Blue   *   .
SIB LEDs:
  SIB  0   1   2   3   4
--------------------------
Red    .   .   .   .   .
Green  *   *   *   *   *

To display the amount of time the routing matrix components have been in operation, issue the show system uptime command on the TX Matrix router:


user@router> show system uptime
scc-re0:
--------------------------------------------------------------------------
Current time: 2004-09-27 09:44:55 PDT
System booted: 2004-09-27 08:49:31 PDT (00:55:24 ago)
Protocols started: 2004-09-27 08:50:27 PDT (00:54:28 ago)
Last configured: 2004-09-27 09:16:08 PDT (00:28:47 ago) by regress
9:44AM PDT up 55 mins, 1 user, load averages: 0.00, 0.05, 0.06
lcc0-re0:
--------------------------------------------------------------------------
Current time: 2004-09-27 09:44:55 PDT
System booted: 2004-09-27 08:49:24 PDT (00:55:31 ago)
Last configured: 2004-09-27 09:16:06 PDT (00:28:49 ago) by regress
9:44AM PDT up 56 mins, 0 users, load averages: 0.00, 0.02, 0.00
lcc2-re0:
--------------------------------------------------------------------------
Current time: 2004-09-27 09:44:55 PDT
System booted: 2004-09-27 08:49:26 PDT (00:55:29 ago)
Last configured: 2004-09-27 09:16:06 PDT (00:28:49 ago) by regress
9:44AM PDT up 55 mins, 0 users, load averages: 0.02, 0.01, 0.00

Displaying Chassis Hardware and Status for a Routing Matrix with a TX Matrix Router

To display the hardware inventory for a routing matrix with a TX Matrix router, you can select output for the TX Matrix router only, a specific T640 router, or all components. If a specific component (lcc or scc) is not specified as an option in the command, the default output displays information for the entire routing matrix.


user@router> show chassis hardware ?
Possible completions:
  <[Enter]>            Execute this command
  detail               Include RAM and disk information in output
  extensive            Display ID EEPROM information
  frus                 Display assembly IDs and extra PIC information
   lcc                  Display chassis-specific information (0..3)
  scc                  Display chassis-specific information
  |                    Pipe through a command

To display all hardware components in a routing matrix, issue the show chassis hardware command on the TX Matrix router:


user@router> show chassis hardware
scc-re0:
--------------------------------------------------------------------------
Hardware inventory:
Item             Version  Part number  Serial number     Description
Chassis                                                  TX Matrix
Midplane         REV 04   710-004396   RB0013            SCC Midplane
FPM GBUS        
FPM Display      REV 04   710-004619   HS5953            SCC FPM
CIP 0            REV 01   710-010218   HS5726            SCC CIP
CIP 1            REV 01   710-010218   HV9163            SCC CIP
PEM 0            Rev 11   740-002595   pm18529           Power Entry Module
Routing Engine 0 REV 02   740-008883   212058900121      RE-4.0
Routing Engine 1 REV 03   740-008883   211123900258      RE-4.0
CB 0             REV 01   710-011709   HS5911            Control Board (CB-TX)
CB 1             REV 01   710-011709   HZ2163            Control Board (CB-TX)
SPMB 0           REV 09   710-003229   HT4129            T-series Switch CPU
SPMB 1           REV 09   710-003229   HT4174            T-series Switch CPU
SIB 0            REV 01   710-011223   HS0663            SIB-S8-F16 1/2
  B Board        REV 05   710-011225   HW1210            SIB-S8-F16 1/2 (B)
SIB 1            REV 01   710-005839   HW1160            SIB-S8-F16
  B Board        REV 01   710-005840   HW1213            SIB-S8-F16 (B)
SIB 2            REV 05   710-011223   HW1146            SIB-S8-F16 1/2
  B Board        REV 05   710-011225   JB8148            SIB-S8-F16 1/2 (B)
SIB 3            REV 05   710-011223   HW1218            SIB-S8-F16 1/2
  B Board        REV 05   710-011225   HW1214            SIB-S8-F16 1/2 (B)
SIB 4            REV 05   710-011223   HW1162            SIB-S8-F16 1/2
  B Board        REV 05   710-011225   HW1182            SIB-S8-F16 1/2 (B)
lcc0-re0:
--------------------------------------------------------------------------
Hardware inventory:
Item             Version  Part number  Serial number     Description
Chassis                                65409             T640
Midplane         REV 03   710-005608   RA1395            T640 Backplane
FPM GBUS         REV 09   710-002901   RA2649            T640 FPM Board
FPM Display      REV 05   710-002897   RA2608            FPM Display
CIP              REV 06   710-002895   HS0753            T-series CIP
PEM 0            Rev 01   740-002595   MF16629           Power Entry Module
SCG 0            REV 11   710-003423   HS4313            T640 Sonet Clock Gen.
SCG 1            REV 11   710-003423   HR9161            T640 Sonet Clock Gen.
Routing Engine 0 REV 03   740-008883   211123900199      RE-4.0
Routing Engine 1 REV 03   740-008883   211123900248      RE-4.0
CB 0             REV 02   710-007655   HS5909            Control Board (CB-T)
CB 1             REV 02   710-007655   HS5910            Control Board (CB-T)
FPC 1            REV 07   710-007527   HR0716            FPC Type 2
  CPU            REV 15   710-001726   HS6048            FPC CPU
  PIC 0          REV 07   750-001900   AR3722            1x OC-48 SONET, SMSR
  PIC 1          REV 05   750-001900   AD3644            1x OC-48 SONET, SMSR
  PIC 3          REV 06   750-001900   HD7603            1x OC-48 SONET, SMSR
  MMB 1          REV 03   710-005555   HT5273            MMB-288mbit
  PPB 0          REV 04   710-003758   HR4249            PPB Type 2
  PPB 1          REV 04   710-003758   HR4257            PPB Type 2
FPC 2            REV 01   710-010233   HM4189            E-FPC Type 1
  CPU            REV 01   710-010169   HS9936            FPC CPU-Enhanced
  PIC 1          REV 03   750-005719   HL8326            1x OC-12 ATM-II IQ, MM
  PIC 2          REV 01   750-003141   AD9051            1x G/E, 1000 BASE-SX
  MMB 1          REV 01   710-008923   HR0848            MMB 3M 288-bit
FPC 3            REV 01   710-010154   HR0863            E-FPC Type 3
  CPU            REV 01   710-010169   HN3422            FPC CPU-Enhanced
  PIC 3          REV 01   750-009553   HP3576            4x OC-48 SONET
    SFP 0        REV 01   740-009030   P11H5N1           SFP-LR
    SFP 1        REV 01   740-009029   35D464P00060      SFP-IR
    SFP 3        REV 01   740-009030   P11H5LM           SFP-LR
  MMB 0          REV 01   710-010171   HR0821            MMB-288mbit
  MMB 1          REV 01   710-010171   HR0818            MMB-288mbit
SPMB 0           REV 09   710-003229   HT4177            T-series Switch CPU
SPMB 1           REV 09   710-003229   HT4176            T-series Switch CPU
SIB 0            REV 07   710-005781   HR5939            SIB-L8-F16
  B Board        REV 06   710-005782   HR5944            SIB-L8-F16 (B)
SIB 1            REV 02   710-005781   HZ2146            SIB-L8-F16
  B Board        REV 03   710-005782   HY4160            SIB-L8-F16 (B)
SIB 2            REV 07   710-005781   HR5925            SIB-L8-F16
  B Board        REV 03   710-005782   HY4161            SIB-L8-F16 (B)
SIB 3            REV 07   710-005781   HR5918            SIB-L8-F16
  B Board        REV 06   710-005782   HR5972            SIB-L8-F16 (B)
SIB 4            REV 07   710-005781   HR5935            SIB-L8-F16
  B Board        REV 06   710-005782   HR5969            SIB-L8-F16 (B)
lcc2-re0:
--------------------------------------------------------------------------
Hardware inventory:
Item             Version  Part number  Serial number     Description
Chassis                                55609             T640
Midplane         REV 03   710-005608   RA1444            T640 Backplane
FPM GBUS         REV 09   710-002901   RA3309            T640 FPM Board
FPM Display      REV 05   710-002897   RA3273            FPM Display
CIP              REV 06   710-002895   HS0735            T-series CIP
PEM 0            Rev 11   740-002595   PM18568           Power Entry Module
PEM 1            Rev 11   740-002595   PM18572           Power Entry Module
SCG 0            REV 11   710-003423   HS9991            T640 Sonet Clock Gen.
Routing Engine 0 REV 03   740-008883   211123900183      RE-4.0
Routing Engine 1 REV 02   740-008883   212058900178      RE-4.0
CB 0             REV 02   710-007655   HS5913            Control Board (CB-T)
CB 1             REV 02   710-007655   HS5944            Control Board (CB-T)
FPC 0            REV 05   710-001721   HD5965            FPC Type 3
  CPU            REV 09   710-001726   AY4909            FPC CPU
  PIC 0          REV 04   750-009553   HV3648            4x OC-48 SONET
    SFP 0        REV 01   740-009029   P11JXWP           SFP-IR
    SFP 1        REV 01   740-008169   36D525P00154      UNKNOWN
    SFP 2        REV 01   740-009028   2353110           SFP-SR
    SFP 3        REV 01   740-008169   36D525P00159      UNKNOWN
  PIC 1          REV 02   750-009567   HX2875            1x 10GE(LAN),XENPAK
    SFP 0        REV 01   740-009898   USC202YW25        XENPAK-LR
  MMB 0          REV 03   710-004047   HE3427            MMB-288mbit
  MMB 1          REV 03   710-004047   HD5812            MMB-288mbit
  ICBM           REV 04   710-003384   HB1884            FPC ICBM
  PPB 0          REV 02   710-002845   HC0964            PPB Type 3
  PPB 1          REV 02   710-002845   HC0987            PPB Type 3
FPC 1            REV 02   710-002385   HC0618            FPC Type 2
  CPU            REV 06   710-001726   HA4724            FPC CPU
  PIC 0          REV 02   750-009066   HL9900            1x OC-48 SONET SFP
    SFP 0                 NON-JNPR     P11QS8W           SFP-LR
  PIC 1          REV 02   750-007219   AZ1339            2x OC-12 ATM-II IQ, MM
  PIC 2          REV 02   750-002510   AP7476            2x G/E, 1000 BASE-SX
  PIC 3          REV 05   750-001900   AD5738            1x OC-48 SONET, SMSR
  MMB 1          REV 03   710-004047   HD5829            MMB-288mbit
  ICBM           REV 04   710-003384   HC0386            FPC ICBM
  PPB 0          REV 02   710-003758   HC0904            PPB Type 2
  PPB 1          REV 02   710-003758   HC0898            PPB Type 2
FPC 3            REV 07   710-007529   HR3311            FPC Type 3
  CPU            REV 15   710-001726   HR2788            FPC CPU
  PIC 0          REV 10   750-004535   HT0545            1x OC-192 SM SR2
  PIC 1          REV 12   750-004535   HX2065            1x OC-192 SM SR2
  PIC 2          REV 01   750-004535   HC0241            1x OC-192 SM SR1
  PIC 3          REV 01   750-004535   HF6583            1x OC-192 SM SR1
  MMB 0          REV 03   710-005555   HR5642            MMB-288mbit
  MMB 1          REV 03   710-005555   HR5586            MMB-288mbit
  PPB 0          REV 04   710-002845   HT6719            PPB Type 3
  PPB 1          REV 04   710-002845   HM0206            PPB Type 3
SPMB 0           REV 09   710-003229   HR8685            T-series Switch CPU
SPMB 1           REV 09   710-003229   HR3730            T-series Switch CPU
SIB 0            REV 07   710-005781   HR5937            SIB-L8-F16
  B Board        REV 06   710-005782   HZ5288            SIB-L8-F16 (B)
SIB 1            REV 07   710-005781   HZ5279            SIB-L8-F16
  B Board        REV 06   710-005782   HR5951            SIB-L8-F16 (B)
SIB 2            REV 07   710-005781   HZ5276            SIB-L8-F16
  B Board        REV 06   710-005782   HR5950            SIB-L8-F16 (B)
SIB 3            REV 07   710-005781   HR5915            SIB-L8-F16
  B Board        REV 06   710-005782   HZ5285            SIB-L8-F16 (B)
SIB 4            REV 07   710-005781   HR5934            SIB-L8-F16
  B Board        REV 06   710-005782   HR5952            SIB-L8-F16 (B)

 

You can also display individual hardware components in the TX Matrix router, a specific T640 router, or the entire routing matrix. To display all the SIBs in the entire routing matrix, issue the show chassis sibs command on the TX Matrix router.


user@router> show chassis sibs
scc-re0:
--------------------------------------------------------------------------
Slot  State               Uptime
 0    Spare           
 1    Online             53 minutes, 38 seconds
 2    Online             53 minutes, 36 seconds
 3    Online             53 minutes, 33 seconds
 4    Online             53 minutes, 30 seconds
lcc0-re0:
--------------------------------------------------------------------------
Slot  State               Uptime
 0    Spare           
 1    Online             53 minutes, 18 seconds
 2    Online             53 minutes, 17 seconds
 3    Online             53 minutes, 16 seconds
 4    Online             53 minutes, 15 seconds
lcc2-re0:
--------------------------------------------------------------------------
Slot  State               Uptime
 0    Spare           
 1    Online             53 minutes, 18 seconds
 2    Online             53 minutes, 17 seconds
 3    Online             53 minutes, 16 seconds
 4    Online             53 minutes, 15 seconds

To display information about all master Routing Engines in the routing matrix, issue the show chassis routing-engine command on the TX Matrix router:


user@router> show chassis routing-engine
scc-re0:
--------------------------------------------------------------------------
Routing Engine status:
  Slot 0:
    Current state                  Master
    Election priority              Master (default)
    Temperature                 34 degrees C / 93 degrees F
    CPU temperature             35 degrees C / 95 degrees F
    DRAM                      2048 MB
    Memory utilization          12 percent
    CPU utilization:
      User                       0 percent
      Background                 0 percent
      Kernel                     5 percent
      Interrupt                  0 percent
      Idle                      95 percent
    Model                          RE-4.0
    Serial ID                      212058900121
    Start time                     2004-09-27 08:49:31 PDT
    Uptime                        1 hour, 4 seconds
    Load averages:                 1 minute   5 minute  15 minute
                                       0.06       0.04       0.05
Routing Engine status:
  Slot 1:
    Current state                  Backup
    Election priority              Backup (default)
    Temperature                 33 degrees C / 91 degrees F
    CPU temperature             34 degrees C / 93 degrees F
    DRAM                      2048 MB
    Memory utilization          10 percent
    CPU utilization:
      User                       0 percent
      Background                 0 percent
      Kernel                     0 percent
      Interrupt                  1 percent
      Idle                      99 percent
    Model                          RE-4.0
    Serial ID                      211123900258
    Start time                     2004-09-26 13:09:13 PDT
    Uptime                        20 hours, 40 minutes, 4 seconds
lcc0-re0:
--------------------------------------------------------------------------
Routing Engine status:
  Slot 0:
    Current state                  Master
    Election priority              Master (default)
    Temperature                 37 degrees C / 98 degrees F
    CPU temperature             38 degrees C / 100 degrees F
    DRAM                      2048 MB
    Memory utilization          11 percent
    CPU utilization:
      User                       0 percent
      Background                 0 percent
      Kernel                     3 percent
      Interrupt                  1 percent
      Idle                      97 percent
    Model                          RE-4.0
    Serial ID                      211123900199
    Start time                     2004-09-27 08:49:24 PDT
    Uptime                        1 hour, 11 seconds
    Load averages:                 1 minute   5 minute  15 minute
                                       0.02       0.02       0.00
Routing Engine status:
  Slot 1:
    Current state                  Backup
    Election priority              Backup (default)
    Temperature                 35 degrees C / 95 degrees F
    CPU temperature             35 degrees C / 95 degrees F
    DRAM                      2048 MB
    Memory utilization          10 percent
    CPU utilization:
      User                       0 percent
      Background                 0 percent
      Kernel                     0 percent
      Interrupt                  0 percent
      Idle                      99 percent
    Model                          RE-4.0
    Serial ID                      211123900248
    Start time                     2004-09-26 13:09:07 PDT
    Uptime                        20 hours, 40 minutes, 12 seconds
lcc2-re0:
--------------------------------------------------------------------------
Routing Engine status:
  Slot 0:
    Current state                  Master
    Election priority              Master (default)
    Temperature                 33 degrees C / 91 degrees F
    CPU temperature             35 degrees C / 95 degrees F
    DRAM                      2048 MB
    Memory utilization          11 percent
    CPU utilization:
      User                       0 percent
      Background                 0 percent
      Kernel                     4 percent
      Interrupt                  0 percent
      Idle                      96 percent
    Model                          RE-4.0
    Serial ID                      211123900183
    Start time                     2004-09-27 08:49:26 PDT
    Uptime                        1 hour, 9 seconds
    Load averages:                 1 minute   5 minute  15 minute
                                       0.15       0.05       0.01
Routing Engine status:
  Slot 1:
    Current state                  Backup
    Election priority              Backup (default)
    Temperature                 32 degrees C / 89 degrees F
    CPU temperature             34 degrees C / 93 degrees F
    DRAM                      2048 MB
    Memory utilization          10 percent
    CPU utilization:
      User                       0 percent
      Background                 0 percent
      Kernel                     0 percent
      Interrupt                  1 percent
      Idle                      99 percent
    Model                          RE-4.0
    Serial ID                      212058900178
    Start time                     2004-09-26 13:09:10 PDT
    Uptime                        20 hours, 40 minutes, 8 seconds

To display information about FPCs in a routing matrix, issue the show chassis fpc command. Because there are no FPCs in a TX Matrix router, there is no scc option available for this command.


user@router> show chassis fpc
lcc0-re0:
--------------------------------------------------------------------------
                     Temp  CPU Utilization (%)   Memory    Utilization (%)
Slot State            (C)  Total  Interrupt      DRAM (MB) Heap     Buffer
  0  Empty
  1  Online            31      1          0       256         7         44
  2  Online            28      1          0       256         7         44
  3  Online            31      3          0       256        14         44
  4  Empty
  5  Empty
  6  Empty
  7  Empty
lcc2-re0:
--------------------------------------------------------------------------
                     Temp  CPU Utilization (%)   Memory    Utilization (%)
Slot State            (C)  Total  Interrupt      DRAM (MB) Heap     Buffer
  0  Online            31      3          0       256        14         44
  1  Online            30      2          0       256         7         44
  2  Empty
  3  Online            31      3          0       256        14         44
  4  Empty
  5  Empty
  6  Empty
  7  Empty

You can also check to see if the TX Matrix router and T640 routers are communicating correctly within the routing matrix. To verify that the T640 routers have proper connectivity to the routing matrix, issue the show chassis lccs command. In this example, there are two T640 routers in the routing matrix.


user@router> show chassis lccs
Slot  State               Uptime
 0    Online             52 minutes, 5 seconds
 1    Empty
 2    Online             52 minutes, 6 seconds
 3    Empty

Published: 2010-04-15