-- -- read-write/read-create objects have been changed to read-only -- since this implmentation does not support write/create access. -- JUNIPER-VPN-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Counter64, Gauge32, Integer32, TimeTicks, Unsigned32 FROM SNMPv2-SMI InetAddress, InetAddressType FROM INET-ADDRESS-MIB InterfaceIndexOrZero FROM IF-MIB TEXTUAL-CONVENTION, RowStatus, StorageType FROM SNMPv2-TC SnmpAdminString FROM SNMP-FRAMEWORK-MIB jnxMibs FROM JUNIPER-SMI; jnxVpnMIB MODULE-IDENTITY LAST-UPDATED "201010150000Z" ORGANIZATION "IETF Provider Provisioned VPNs WG" CONTACT-INFO " Kireeti Kompella Postal: Juniper Networks, Inc. 1194 Mathilda Ave Sunnyvale, CA 94089 Tel: +1 408 745 2000 E-mail: kireeti@juniper.net" DESCRIPTION "Extended VPN MIB module to support VPN Identifier for locally switched L2 circuits." -- revision history REVISION "201010150000Z" DESCRIPTION "Corrected DISPLAY-HINT for TEXTUAL-CONVENTIONs associated with a JnxVpnIdentifier." REVISION "201008270000Z" DESCRIPTION "Corrected related TEXTUAL-CONVENTIONs associated with a JnxVpnIdentifier." REVISION "200204212128Z" DESCRIPTION "A VPN MIB module that allows one to configure and monitor several types of Provider Provisioned VPNs. Initial revision." ::= { jnxMibs 26 } jnxVpnMIBNotifications OBJECT IDENTIFIER ::= { jnxVpnMIB 0 } jnxVpnMibObjects OBJECT IDENTIFIER ::= { jnxVpnMIB 1 } jnxVpnMIBConformance OBJECT IDENTIFIER ::= { jnxVpnMIB 2 } -- Textual Conventions JnxVpnName ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Name of the VPN." SYNTAX OCTET STRING (SIZE (1..128)) JnxVpnType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Type of the VPN. The following types have been defined: bgpIpVpn: RFC 4364 VPNs; bgpL2Vpn: BGP-based Layer 2 VPNs (see draft-kompella-ppvpn-l2vpn); bgpVpls: BGP-based VPLS (see draft-kompella-ppvnp-vpls); l2Circuit: LDP-based point-to-point Layer 2 circuits (see RFC 4906); ldpVpls: LDP-based VPLS (see draft-lasserre-vkompella-ppvpn-vpls); opticalVpn: BGP-based Optical (port based) VPNs (see draft-ouldbrahim-bgpgmpls-ovpn); vpOxc: Virtual Private Optical Cross-Connect (see draft-ouldbrahim-ppvpn-vpoxc); ccc: proprietary Layer 2 circuit; bgpAtmVpn: ATM over MPLS (draft to be published)." SYNTAX INTEGER { other(1), bgpIpVpn(2), bgpL2Vpn(3), bgpVpls(4), l2Circuit(5), ldpVpls(6), opticalVpn(7), vpOxc(8), ccc(9), bgpAtmVpn(10) } JnxVpnIdentifierType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Type of the VPN Identifier. This includes Route Distinguishers, Route Targets, and VC IDs. none(0) This value MUST be used if the value of the corresponding JnxVpnIdentifier object is a zero-length string. other(1) A VPN identifier that does not match one of the types defined in this MIB. routeDistinguisher(2) A VPN identifier as defined by the JnxVpnRouteDistinguisher textual convention. routeDistinguisher0(3) A VPN identifier as defined by the JnxVpnRouteDistinguisher0 textual convention. routeDistinguisher1(4) A VPN identifier as defined by the JnxVpnRouteDistinguisher1 textual convention. routeDistinguisher2(5) A VPN identifier as defined by the JnxVpnRouteDistinguisher2 textual convention. routeTarget(6) A VPN identifier as defined by the JnxVpnRouteTarget textual convention. routeTarget0(7) A VPN identifier as defined by the JnxVpnRouteTarget0 textual convention. routeTarget1(8) A VPN identifier as defined by the JnxVpnRouteTarget1 textual convention. routeTarget2(9) A VPN identifier as defined by the JnxVpnRouteTarget2 textual convention. vcId(10) A VPN identifier as defined by the JnxVpnVCIdentifier textual convention. localSwitch(11) A VPN identifier as defined by the JnxVpnLocalSwitchIdentifier textual convention." SYNTAX INTEGER { none(0), other(1), routeDistinguisher(2), routeDistinguisher0(3), routeDistinguisher1(4), routeDistinguisher2(5), routeTarget(6), routeTarget0(7), routeTarget1(8), routeTarget2(9), vcId(10), localSwitch(11) } JnxVpnIdentifier ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Syntax for a VPN identifier. A VPN Identifier is always interpreted within the context of an jnxVpnIdentifierType value. The jnxVpnIdentifierType object which defines the context must be registered immediately before the object which uses the VpnIdentifier textual convention. In other words, the object identifiers for the jnxVpnIdentifierType object and the jnxVpnIdentifier object MUST have the same length and the last sub-identifier of the jnxVpnIdentifierType object MUST be 1 less than the last sub-identifier of the jnxVpnIdentifier object." SYNTAX OCTET STRING(SIZE (0..256)) JnxVpnRouteDistinguisher ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x:1x:1x:1x:1x:1x:1x:1x" STATUS current DESCRIPTION "Represents a Generic Route Distinguisher." REFERENCE "BGP/MPLS VPNs, RFC 4364." SYNTAX OCTET STRING(SIZE (8)) JnxVpnRouteDistinguisher0 ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x-2d:4d" STATUS current DESCRIPTION "Represents a Type 0 Route Distinguisher." REFERENCE "BGP/MPLS VPNs, RFC 4364." SYNTAX OCTET STRING(SIZE (8)) JnxVpnRouteDistinguisher1 ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x-1d.1d.1d.1d:2d" STATUS current DESCRIPTION "Represents a Type 1 Route Distinguisher." REFERENCE "BGP/MPLS VPNs, RFC 4364." SYNTAX OCTET STRING(SIZE (8)) JnxVpnRouteDistinguisher2 ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x-4d:2d" STATUS current DESCRIPTION "Represents a Type 2 Route Distinguisher." REFERENCE "BGP/MPLS VPNs, RFC 4364." SYNTAX OCTET STRING(SIZE (8)) JnxVpnRouteTarget ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x:1x:1x:1x:1x:1x:1x:1x" STATUS current DESCRIPTION "Represents a Generic Route Target." REFERENCE "BGP Extended Communities Attribute, RFC 4360." SYNTAX OCTET STRING(SIZE (8)) JnxVpnRouteTarget0 ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x-4d:2d" STATUS current DESCRIPTION "Represents a Type 00 Route Target." REFERENCE "BGP Extended Communities Attribute, RFC 4360." SYNTAX OCTET STRING(SIZE (8)) JnxVpnRouteTarget1 ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x-1d.1d.1d.1d:2d" STATUS current DESCRIPTION "Represents a Type 01 Route Target." REFERENCE "BGP Extended Communities Attribute, RFC 4360." SYNTAX OCTET STRING(SIZE (8)) JnxVpnRouteTarget2 ::= TEXTUAL-CONVENTION DISPLAY-HINT "2x-2d:4d" STATUS current DESCRIPTION "Represents a Type 02 Route Target." REFERENCE "BGP Extended Communities Attribute, RFC 4360." SYNTAX OCTET STRING(SIZE (8)) JnxVpnVCIdentifier ::= TEXTUAL-CONVENTION DISPLAY-HINT "1d.1d.1d.1d:4d" STATUS current DESCRIPTION "Represents a PE ID, VC ID pair. The PE ID is the Router ID of the remote PE. The VC ID follows the description given in draft-martini-l2circuit-trans." SYNTAX OCTET STRING(SIZE (8)) JnxVpnMultiplexor ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Syntax for a VPN multiplexor/demultiplexor within a Pseudo-Wire Tunnel." SYNTAX Unsigned32 JnxVpnLocalSwitchIdentifier ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The string representing the name of two interfaces that are being locally switched separated by a colon." SYNTAX OCTET STRING(SIZE (1..256)) -- vpnInfo jnxVpnInfo OBJECT IDENTIFIER ::= { jnxVpnMibObjects 1 } jnxVpnConfiguredVpns OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of configured VPNs." ::= { jnxVpnInfo 1 } jnxVpnActiveVpns OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of active VPNs." ::= { jnxVpnInfo 2 } jnxVpnNextIfIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Next free VPN interface index." ::= { jnxVpnInfo 3 } jnxVpnNextPwIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Next free Pseudo-Wire index." ::= { jnxVpnInfo 4 } jnxVpnNextRTIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Next free Route Target index." ::= { jnxVpnInfo 5 } -- vpnTable jnxVpnTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxVpnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Configured VPNs." ::= { jnxVpnMibObjects 2 } jnxVpnEntry OBJECT-TYPE SYNTAX JnxVpnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing information about a particular VPN." INDEX { jnxVpnType, jnxVpnName } ::= { jnxVpnTable 1 } JnxVpnEntry ::= SEQUENCE { -- Indices jnxVpnType JnxVpnType, jnxVpnName JnxVpnName, -- Conceptual row information jnxVpnRowStatus RowStatus, jnxVpnStorageType StorageType, -- Configured information jnxVpnDescription SnmpAdminString, jnxVpnIdentifierType JnxVpnIdentifierType, jnxVpnIdentifier JnxVpnIdentifier, -- Dynamic information jnxVpnConfiguredSites Gauge32, jnxVpnActiveSites Gauge32, jnxVpnLocalAddresses Gauge32, jnxVpnTotalAddresses Gauge32, jnxVpnAge TimeTicks } jnxVpnType OBJECT-TYPE SYNTAX JnxVpnType MAX-ACCESS not-accessible -- MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the VPN." ::= { jnxVpnEntry 1 } jnxVpnName OBJECT-TYPE SYNTAX JnxVpnName MAX-ACCESS not-accessible -- MAX-ACCESS read-only STATUS current DESCRIPTION "Name of the VPN. This should ideally be unique in the Service Provider's domain; at a minimum, it MUST be unique per Provider Edge router." ::= { jnxVpnEntry 2 } jnxVpnRowStatus OBJECT-TYPE SYNTAX RowStatus -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." ::= { jnxVpnEntry 3 } jnxVpnStorageType OBJECT-TYPE SYNTAX StorageType -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { jnxVpnEntry 4 } jnxVpnDescription OBJECT-TYPE SYNTAX SnmpAdminString -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "String describing the VPN." ::= { jnxVpnEntry 5 } jnxVpnIdentifierType OBJECT-TYPE SYNTAX JnxVpnIdentifierType -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the following JnxVpnIdentifier." ::= { jnxVpnEntry 6 } jnxVpnIdentifier OBJECT-TYPE SYNTAX JnxVpnIdentifier -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "In the case of BGP VPNs, this is the Route Distinguisher for the VPN. In the case of LDP VPNs, this is the VC ID for the circuit. A value of all zeros indicates that the neither a Route Distinguisher nor a VC ID is configured for the VPN." ::= { jnxVpnEntry 7 } jnxVpnConfiguredSites OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of sites configured in the VPN. Must be set to zero if not applicable." ::= { jnxVpnEntry 8 } jnxVpnActiveSites OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of active sites (i.e., sites whose state is active) in the VPN." ::= { jnxVpnEntry 9 } jnxVpnLocalAddresses OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of addresses learned from the CE device." ::= { jnxVpnEntry 10 } jnxVpnTotalAddresses OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of addresses in the VPN RIB." ::= { jnxVpnEntry 11 } jnxVpnAge OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The age (i.e., time from creation till now) of this VPN in hundredths of a second." ::= { jnxVpnEntry 12 } -- vpn interface table jnxVpnIfTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxVpnIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of VPN Interfaces." ::= { jnxVpnMibObjects 3 } jnxVpnIfEntry OBJECT-TYPE SYNTAX JnxVpnIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing information about a particular VPN interface." INDEX { jnxVpnIfVpnType, jnxVpnIfVpnName, jnxVpnIfIndex } ::= { jnxVpnIfTable 1 } JnxVpnIfEntry ::= SEQUENCE { -- Indices jnxVpnIfVpnType JnxVpnType, jnxVpnIfVpnName JnxVpnName, jnxVpnIfIndex Unsigned32, -- Conceptual row information jnxVpnIfRowStatus RowStatus, jnxVpnIfStorageType StorageType, -- Configured information jnxVpnIfAssociatedPw Unsigned32, jnxVpnIfProtocol INTEGER, jnxVpnIfInBandwidth Unsigned32, jnxVpnIfOutBandwidth Unsigned32, -- Dynamic information jnxVpnIfStatus INTEGER } jnxVpnIfVpnType OBJECT-TYPE SYNTAX JnxVpnType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Type of the VPN to which this interface belongs." ::= { jnxVpnIfEntry 1 } jnxVpnIfVpnName OBJECT-TYPE SYNTAX JnxVpnName MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "Name of the VPN to which this interface belongs." ::= { jnxVpnIfEntry 2 } jnxVpnIfIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The index of this interface in the VPN. Each interface in the VPN is given a unique index. The RowStatus says whether a given interface (i.e., a row in this table) is valid or not. Note: this index MUST NOT be zero." ::= { jnxVpnIfEntry 3 } jnxVpnIfRowStatus OBJECT-TYPE SYNTAX RowStatus -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." ::= { jnxVpnIfEntry 4 } jnxVpnIfStorageType OBJECT-TYPE SYNTAX StorageType -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { jnxVpnIfEntry 5 } jnxVpnIfAssociatedPw OBJECT-TYPE SYNTAX Unsigned32 -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "Index of associated Pseudo-wire, if any, in which case the index MUST be non-zero. If none, then this index MUST be zero." ::= { jnxVpnIfEntry 6 } jnxVpnIfProtocol OBJECT-TYPE SYNTAX INTEGER { other(0), frameRelay(1), atmAal5(2), atmCell(3), ethernetVlan(4), ethernet(5), ciscoHdlc(6), ppp(7), cem(8), atmVcc(9), atmVpc(10), vpls(11), ipInterworking(12), snapInterworking(13), frameRelayPort(15), satope1(17), satopt1(18), static(20), rip(21), ospf(22), bgp(23), satope3(24), satopt3(25), cesop(26), atmTrunkNNI(129), atmTrunkUNI(130) } -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "Protocol running over this VPN interface. The values up to 10 are taken from draft-martini-l2circuit-trans-mpls-08.txt; the value for vpls is taken from draft-lasserre-vkompella-ppvpn-vpls-01.txt. The values from 20-23 are used when the VPN is a Layer 3 VPN." ::= { jnxVpnIfEntry 7 } jnxVpnIfInBandwidth OBJECT-TYPE SYNTAX Unsigned32 -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum bandwidth that the CE connected over this VPN i/f can send to the PE, in Kilo (i.e., 1000) Bytes per second. A value of zero means there is no configured maximum." ::= { jnxVpnIfEntry 8 } jnxVpnIfOutBandwidth OBJECT-TYPE SYNTAX Unsigned32 -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "Maximum bandwidth that the PE can send to the CE over this VPN interface, in Kilo (i.e., 1000) Bytes per second. A value of zero means there is no configured maximum." ::= { jnxVpnIfEntry 9 } jnxVpnIfStatus OBJECT-TYPE SYNTAX INTEGER { unknown(0), noLocalInterface(1), disabled(2), encapsulationMismatch(3), down(4), up(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of this interface." ::= { jnxVpnIfEntry 10 } -- vpnPwTable jnxVpnPwTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxVpnPwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Pseudo-Wire Connections." ::= { jnxVpnMibObjects 4 } jnxVpnPwEntry OBJECT-TYPE SYNTAX JnxVpnPwEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing information about a particular VPN." INDEX { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } ::= { jnxVpnPwTable 1 } JnxVpnPwEntry ::= SEQUENCE { -- Indices jnxVpnPwVpnType JnxVpnType, jnxVpnPwVpnName JnxVpnName, jnxVpnPwIndex Unsigned32, -- Conceptual row information jnxVpnPwRowStatus RowStatus, jnxVpnPwStorageType StorageType, -- Information about the Pseudo-Wire jnxVpnPwAssociatedInterface Unsigned32, jnxVpnPwLocalSiteId Unsigned32, jnxVpnPwRemoteSiteId Unsigned32, jnxVpnRemotePeIdAddrType InetAddressType, jnxVpnRemotePeIdAddress InetAddress, jnxVpnPwTunnelType INTEGER, jnxVpnPwTunnelName SnmpAdminString, jnxVpnPwReceiveDemux JnxVpnMultiplexor, jnxVpnPwTransmitDemux JnxVpnMultiplexor, -- Status information jnxVpnPwStatus INTEGER, jnxVpnPwTunnelStatus INTEGER, jnxVpnPwRemoteSiteStatus INTEGER, jnxVpnPwTimeUp TimeTicks, jnxVpnPwTransitions Gauge32, jnxVpnPwLastTransition TimeTicks, -- Performance data jnxVpnPwPacketsSent Counter64, jnxVpnPwOctetsSent Counter64, jnxVpnPwPacketsReceived Counter64, jnxVpnPwOctetsReceived Counter64, jnxVpnPwLRPacketsSent Counter32, jnxVpnPwLROctetsSent Counter32, jnxVpnPwLRPacketsReceived Counter32, jnxVpnPwLROctetsReceived Counter32 } jnxVpnPwVpnType OBJECT-TYPE SYNTAX JnxVpnType MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The type of the VPN to which this Pseudo-Wire belongs." ::= { jnxVpnPwEntry 1 } jnxVpnPwVpnName OBJECT-TYPE SYNTAX JnxVpnName MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The name of the VPN to which this Pseudo-Wire belongs." ::= { jnxVpnPwEntry 2 } jnxVpnPwIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The index of this Pseudo-Wire in the VPN. Each Pseudo Wire in the VPN is given a unique index. The RowStatus says whether a given Pseudo Wire (i.e., a row in this table) is valid or not. Note: this index MUST NOT be zero." ::= { jnxVpnPwEntry 3 } jnxVpnPwRowStatus OBJECT-TYPE SYNTAX RowStatus -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." ::= { jnxVpnPwEntry 4 } jnxVpnPwStorageType OBJECT-TYPE SYNTAX StorageType -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { jnxVpnPwEntry 5 } jnxVpnPwAssociatedInterface OBJECT-TYPE SYNTAX Unsigned32 -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The VPN index of the interface associated with this Pseudo Wire, if any. If there is no interface associated with this Pseudo Wire, a value of zero is to be returned." ::= { jnxVpnPwEntry 6 } jnxVpnPwLocalSiteId OBJECT-TYPE SYNTAX Unsigned32 -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The local site identifier for this Pseudo-Wire. If there is no local site identifier, a value of zero is to be returned." ::= { jnxVpnPwEntry 7 } jnxVpnPwRemoteSiteId OBJECT-TYPE SYNTAX Unsigned32 -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The remote site (i.e., the site at the other end of this Pseudo-Wire) identifier. If there is no remote site identifier, a value of zero is to be returned." ::= { jnxVpnPwEntry 8 } jnxVpnRemotePeIdAddrType OBJECT-TYPE SYNTAX InetAddressType -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The type of address assigned to the remote PE." ::= { jnxVpnPwEntry 9 } jnxVpnRemotePeIdAddress OBJECT-TYPE SYNTAX InetAddress -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The address of the remote PE, i.e., the router at the other end of the Pseudo-Wire." ::= { jnxVpnPwEntry 10 } jnxVpnPwTunnelType OBJECT-TYPE SYNTAX INTEGER { static(1), gre(2), l2tpv3(3), ipSec(4), ldp(5), rsvpTe(6), crLdp(7) } -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the tunnel over which the Pseudo-Wire is carried. If several Pseudo-Wires can be carried in one tunnel, each Pseudo-Wire is identified by the multiplexor/ demultiplexor within this tunnel." ::= { jnxVpnPwEntry 11 } jnxVpnPwTunnelName OBJECT-TYPE SYNTAX SnmpAdminString -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the Tunnel over which this Pseudo-Wire is carried, if any." ::= { jnxVpnPwEntry 12 } jnxVpnPwReceiveDemux OBJECT-TYPE SYNTAX JnxVpnMultiplexor -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the demultiplexor that identifies received packets as belonging to this Pseudo-Wire, if any." ::= { jnxVpnPwEntry 13 } jnxVpnPwTransmitDemux OBJECT-TYPE SYNTAX JnxVpnMultiplexor -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the demultiplexor that identifies transmitted packets as belonging to this Pseudo-Wire, if any." ::= { jnxVpnPwEntry 14 } jnxVpnPwStatus OBJECT-TYPE SYNTAX INTEGER { unknown(0), down(1), up(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the Pseudo-Wire." ::= { jnxVpnPwEntry 15 } jnxVpnPwTunnelStatus OBJECT-TYPE SYNTAX INTEGER { unknown(0), down(1), testing(2), up(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the PE-to-PE tunnel over which the Pseudo- Wire is carried." ::= { jnxVpnPwEntry 16 } jnxVpnPwRemoteSiteStatus OBJECT-TYPE SYNTAX INTEGER { unknown(0), outOfRange(1), down(2), up(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Status of the interface at the remote end of the Pseudo-Wire." ::= { jnxVpnPwEntry 17 } jnxVpnPwTimeUp OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The total time in hundredths of a second that this Pseudo-Wire has been operational." ::= { jnxVpnPwEntry 18 } jnxVpnPwTransitions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of state transitions (up -> down and down -> up) this Tunnel has undergone." ::= { jnxVpnPwEntry 19 } jnxVpnPwLastTransition OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time in hundredths of a second since the last transition occurred on this Tunnel." ::= { jnxVpnPwEntry 20 } jnxVpnPwPacketsSent OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets that have been sent over this Pseudo-Wire." ::= { jnxVpnPwEntry 21 } jnxVpnPwOctetsSent OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets that have been sent over this Pseudo-Wire." ::= { jnxVpnPwEntry 22 } jnxVpnPwPacketsReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets that have been received over this Pseudo-Wire." ::= { jnxVpnPwEntry 23 } jnxVpnPwOctetsReceived OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets that have been received over this Pseudo-Wire." ::= { jnxVpnPwEntry 24 } jnxVpnPwLRPacketsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets that have been sent over this Pseudo-Wire." ::= { jnxVpnPwEntry 25 } jnxVpnPwLROctetsSent OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets that have been sent over this Pseudo-Wire." ::= { jnxVpnPwEntry 26 } jnxVpnPwLRPacketsReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets that have been received over this Pseudo-Wire." ::= { jnxVpnPwEntry 27 } jnxVpnPwLROctetsReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets that have been received over this Pseudo-Wire." ::= { jnxVpnPwEntry 28 } -- Route Target table jnxVpnRTTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxVpnRTEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of Route Targets for a VPN." ::= { jnxVpnMibObjects 5 } jnxVpnRTEntry OBJECT-TYPE SYNTAX JnxVpnRTEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Entry containing information about a particular VPN." INDEX { jnxVpnRTVpnType, jnxVpnRTVpnName, jnxVpnRTIndex } ::= { jnxVpnRTTable 1 } JnxVpnRTEntry ::= SEQUENCE { -- Indices jnxVpnRTVpnType JnxVpnType, jnxVpnRTVpnName JnxVpnName, jnxVpnRTIndex Unsigned32, -- Conceptual row information jnxVpnRTRowStatus RowStatus, jnxVpnRTStorageType StorageType, -- Route Target information jnxVpnRTType JnxVpnIdentifierType, jnxVpnRT JnxVpnIdentifier, jnxVpnRTFunction INTEGER } jnxVpnRTVpnType OBJECT-TYPE SYNTAX JnxVpnType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of the VPN for which this list of Route Targets are defined." ::= { jnxVpnRTEntry 1 } jnxVpnRTVpnName OBJECT-TYPE SYNTAX JnxVpnName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the VPN for which this list of Route Targets are defined." ::= { jnxVpnRTEntry 2 } jnxVpnRTIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index within the list of Route Targets that specifies individual Route Targets that define the VPN. Note: this index MUST NOT be zero." ::= { jnxVpnRTEntry 3 } jnxVpnRTRowStatus OBJECT-TYPE SYNTAX RowStatus -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is used to create, modify, and/or delete a row in this table." ::= { jnxVpnRTEntry 4 } jnxVpnRTStorageType OBJECT-TYPE SYNTAX StorageType -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "This variable indicates the storage type for this object." ::= { jnxVpnRTEntry 5 } jnxVpnRTType OBJECT-TYPE SYNTAX JnxVpnIdentifierType -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the following Route Target. This can one of 'routeTarget[012]' or 'none'." ::= { jnxVpnRTEntry 6 } jnxVpnRT OBJECT-TYPE SYNTAX JnxVpnIdentifier -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "Route Target for the VPN. If the jnxVpnRTType is 'none', this value should be all zeros." ::= { jnxVpnRTEntry 7 } jnxVpnRTFunction OBJECT-TYPE SYNTAX INTEGER { import(1), export(2), both(3) } -- MAX-ACCESS read-create MAX-ACCESS read-only STATUS current DESCRIPTION "The route target export distribution type." ::= { jnxVpnRTEntry 8 } -- -- definition of VPN notifications -- jnxVpnIfUp NOTIFICATION-TYPE OBJECTS { jnxVpnIfVpnType, jnxVpnIfVpnName, jnxVpnIfIndex } STATUS current DESCRIPTION "A jnxVpnIfUp notification is generated when the interface with index jnxVpnIfIndex belonging to the VPN named jnxVpnIfVpnName of type jnxVpnIfVpnType transitions out of the 'down' state." ::= { jnxVpnMIBNotifications 1 } jnxVpnIfDown NOTIFICATION-TYPE OBJECTS { jnxVpnIfVpnType, jnxVpnIfVpnName, jnxVpnIfIndex } STATUS current DESCRIPTION "A jnxVpnIfDown notification is generated when the interface with index jnxVpnIfIndex belonging to the VPN named jnxVpnIfVpnName of type jnxVpnIfVpnType transitions to the 'down' state." ::= { jnxVpnMIBNotifications 2 } jnxVpnPwUp NOTIFICATION-TYPE OBJECTS { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } STATUS current DESCRIPTION "A jnxVpnPwUp notification is generated when the Pseudo-Wire with index jnxVpnPwIndex belonging to the VPN named jnxVpnPwVpnName of type jnxVpnPwVpnType transitions out of the 'down' state." ::= { jnxVpnMIBNotifications 3 } jnxVpnPwDown NOTIFICATION-TYPE OBJECTS { jnxVpnPwVpnType, jnxVpnPwVpnName, jnxVpnPwIndex } STATUS current DESCRIPTION "A jnxVpnPwDown notification is generated when the Pseudo-Wire with index jnxVpnPwIndex belonging to the VPN named jnxVpnPwVpnName of type jnxVpnPwVpnType transitions to the 'down' state." ::= { jnxVpnMIBNotifications 4 } -- End of JUNIPER VPN MIB END