JNX-L2TP-MIB DEFINITIONS ::= BEGIN IMPORTS Integer32, Unsigned32, Counter32, Gauge32, Counter64, TimeTicks, transmission, MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE FROM SNMPv2-SMI DateAndTime, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue FROM SNMPv2-TC CounterBasedGauge64 -- RFC 2856 FROM HCNUM-TC InetAddress, InetAddressType, InetPortNumber FROM INET-ADDRESS-MIB SnmpAdminString FROM SNMP-FRAMEWORK-MIB OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUP FROM SNMPv2-CONF jnxL2tpMibRoot FROM JUNIPER-SMI; jnxL2tp MODULE-IDENTITY LAST-UPDATED "200701110000Z" -- 11 January 2007 ORGANIZATION "Juniper Networks Inc." CONTACT-INFO " Juniper Technical Assistance Center Juniper Networks, Inc. 1194 N. Mathilda Avenue Sunnyvale, CA 94089 E-mail: support@juniper.net" DESCRIPTION "Provides monitoring information regarding the Layer Two Transport Protocol. This MIB is based on the standard MIB defined in RFC 3371. However, there are significant differences including the INDEX fields of l2tpTunnelStatsTable and l2tpSessionStatsTable." -- revision log REVISION "200701110000Z" -- 11 January 2007 DESCRIPTION "Initial revision." ::= { jnxL2tpMibRoot 1 } -- -- Definitions of significant branches -- jnxL2tpObjects OBJECT IDENTIFIER ::= { jnxL2tp 1 } jnxL2tpScalar OBJECT IDENTIFIER ::= { jnxL2tpObjects 1 } jnxL2tpStats OBJECT IDENTIFIER ::= { jnxL2tpScalar 1 } -- -- The L2TP Scalar Status and Statistics Group -- jnxL2tpStatsTotalTunnels OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the total number of tunnels that are currently in the established state. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 1 } jnxL2tpStatsTotalSessions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the total number of sessions that are currently in the established state. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 2 } jnxL2tpStatsControlRxOctets OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of control channel octets received by the existing tunnels. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 3 } jnxL2tpStatsControlRxPkts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of control packets received by the existing tunnels. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 4 } jnxL2tpStatsControlTxOctets OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of control channel octets that were transmitted to the existing tunnel endpoints. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 5 } jnxL2tpStatsControlTxPkts OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of control packets that were transmitted to the existing tunnel endpoints.This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 6 } jnxL2tpStatsPayloadRxOctets OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of payload channel octets that were received on the exisiting tunnels. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 7 } jnxL2tpStatsPayloadRxPkts OBJECT-TYPE SYNTAX CounterBasedGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of payload packets that were received on the existing tunnels. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 8 } jnxL2tpStatsPayloadTxOctets OBJECT-TYPE SYNTAX CounterBasedGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of payload channel octets that were transmitted to the existing tunnel peers. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 9 } jnxL2tpStatsPayloadTxPkts OBJECT-TYPE SYNTAX CounterBasedGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of payload packets that were transmitted to existing tunnel peers. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 10 } jnxL2tpStatsErrorTxPkts OBJECT-TYPE SYNTAX CounterBasedGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of errored packet transmission attempts to the existing tunnel peers. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 11 } jnxL2tpStatsErrorRxPkts OBJECT-TYPE SYNTAX CounterBasedGauge64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the number of errored packets that were received from the existing tunnel peers. This is an instantaneously accumulated value which can increase or decrease depending on number of tunnels established at the time of querying." ::= { jnxL2tpStats 12 } -- -- The L2TP Tunnel Group Status and Statistics Table -- jnxL2tpTunnelGroupStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxL2tpTunnelGroupStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP tunnel group status and statistics table. This table contains objects that can be used to describe the current status and statistics of a single L2TP tunnel group." ::= { jnxL2tpObjects 2 } jnxL2tpTunnelGroupStatsEntry OBJECT-TYPE SYNTAX JnxL2tpTunnelGroupStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An L2TP tunnel group stats entry." INDEX { IMPLIED jnxL2tpTunnelGroupStatsTnlGrpName } ::= { jnxL2tpTunnelGroupStatsTable 1 } JnxL2tpTunnelGroupStatsEntry ::= SEQUENCE { jnxL2tpTunnelGroupStatsTnlGrpName OCTET STRING, jnxL2tpTunnelGroupStatsGatewayAddrType InetAddressType, jnxL2tpTunnelGroupStatsGatewayAddr InetAddress, jnxL2tpTunnelGroupStatsSvcIntfName SnmpAdminString, jnxL2tpTunnelGroupStatsTotalTunnels Gauge32, jnxL2tpTunnelGroupStatsTotalSessions Gauge32 } jnxL2tpTunnelGroupStatsTnlGrpName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1..128)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains the name of this tunnel group." ::= { jnxL2tpTunnelGroupStatsEntry 1 } jnxL2tpTunnelGroupStatsGatewayAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the type of local IP address for L2TP tunnels that are part of this group." ::= { jnxL2tpTunnelGroupStatsEntry 2 } jnxL2tpTunnelGroupStatsGatewayAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the local IP address for L2TP tunnels that are part of this group." ::= { jnxL2tpTunnelGroupStatsEntry 3 } jnxL2tpTunnelGroupStatsSvcIntfName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the name of the service interface that is hosting this tunnel group." ::= { jnxL2tpTunnelGroupStatsEntry 4 } jnxL2tpTunnelGroupStatsTotalTunnels OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the total number of tunnels that are currently in the established state in this tunnel group." ::= { jnxL2tpTunnelGroupStatsEntry 5 } jnxL2tpTunnelGroupStatsTotalSessions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the total number of sessions that are currently in the established state in this tunnel group." ::= { jnxL2tpTunnelGroupStatsEntry 6 } -- -- The L2TP Tunnel Status and Statistics Table -- jnxL2tpTunnelStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxL2tpTunnelStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP tunnel status and statistics table. This table contains objects that can be used to describe the current status and statistics of a single L2TP tunnel." ::= { jnxL2tpObjects 3 } jnxL2tpTunnelStatsEntry OBJECT-TYPE SYNTAX JnxL2tpTunnelStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An L2TP tunnel interface stats entry." INDEX { jnxL2tpTunnelStatsLocalTID } ::= { jnxL2tpTunnelStatsTable 1 } JnxL2tpTunnelStatsEntry ::= SEQUENCE { jnxL2tpTunnelStatsLocalTID Integer32, jnxL2tpTunnelStatsServiceInterface SnmpAdminString, jnxL2tpTunnelStatsTunnelGroup SnmpAdminString, jnxL2tpTunnelStatsRemoteTID Integer32, jnxL2tpTunnelStatsRemoteIpAddrType InetAddressType, jnxL2tpTunnelStatsRemoteIpAddress InetAddress, jnxL2tpTunnelStatsRemoteUdpPort InetPortNumber, jnxL2tpTunnelStatsActiveSessions Gauge32, jnxL2tpTunnelStatsState INTEGER, jnxL2tpTunnelStatsLocalIpAddrType InetAddressType, jnxL2tpTunnelStatsLocalIpAddress InetAddress, jnxL2tpTunnelStatsLocalUdpPort InetPortNumber, jnxL2tpTunnelStatsLocalHostName SnmpAdminString, jnxL2tpTunnelStatsRemoteHostName SnmpAdminString, jnxL2tpTunnelMaxSessions Integer32, jnxL2tpTunnelStatsWindowSize Integer32, jnxL2tpTunnelStatsHelloInterval Integer32, jnxL2tpTunnelStatsCreationTime DateAndTime, jnxL2tpTunnelStatsUpTime TimeTicks, jnxL2tpTunnelStatsIdleTime TimeTicks, jnxL2tpTunnelStatsCollectionStart DateAndTime, jnxL2tpTunnelStatsControlTxPkts Counter32, jnxL2tpTunnelStatsControlTxBytes Counter64, jnxL2tpTunnelStatsControlRxPkts Counter32, jnxL2tpTunnelStatsControlRxBytes Counter64, jnxL2tpTunnelStatsDataTxPkts Counter32, jnxL2tpTunnelStatsDataTxBytes Counter64, jnxL2tpTunnelStatsDataRxPkts Counter32, jnxL2tpTunnelStatsDataRxBytes Counter64, jnxL2tpTunnelStatsErrorTxPkts Counter32, jnxL2tpTunnelStatsErrorRxPkts Counter32 } jnxL2tpTunnelStatsLocalTID OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains the local tunnel Identifier." REFERENCE "RFC 2661, Section 3.1" ::= { jnxL2tpTunnelStatsEntry 1 } jnxL2tpTunnelStatsServiceInterface OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the name of the service interface on which this tunnel is being hosted." ::= { jnxL2tpTunnelStatsEntry 2 } jnxL2tpTunnelStatsTunnelGroup OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the name of the tunnel group that this tunnel is part of." ::= { jnxL2tpTunnelStatsEntry 3 } jnxL2tpTunnelStatsRemoteTID OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the remote tunnel Identifier." REFERENCE "RFC 2661, Section 3.1" ::= { jnxL2tpTunnelStatsEntry 4 } jnxL2tpTunnelStatsRemoteIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the type of the remote end address of this tunnel." ::= { jnxL2tpTunnelStatsEntry 5 } jnxL2tpTunnelStatsRemoteIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the remote end address of this tunnel." ::= { jnxL2tpTunnelStatsEntry 6 } jnxL2tpTunnelStatsRemoteUdpPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the remote end UDP port of this tunnel." ::= { jnxL2tpTunnelStatsEntry 7 } jnxL2tpTunnelStatsActiveSessions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the total number of sessions in the established state for this tunnel." ::= { jnxL2tpTunnelStatsEntry 8 } jnxL2tpTunnelStatsState OBJECT-TYPE SYNTAX INTEGER { cc-responder-accept-new(1), cc-responder-reject-new(2), cc-responder-idle(3), cc-responder-wait-ctl-conn(4), cleanup(5), closed(6), destroyed(7), established(8), terminate(9), unknown(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "This field contains the current state of the control tunnel - one of the internal tunnel state names as described below: cc_responder_accept_new The tunnel has received and accepted the start control connection request (SCCRQ) cc_responder_reject_new The tunnel has received and rejected the SCCRQ cc_responder_idle The tunnel has just been created cc_responder_wait_ctl_conn The tunnel has sent the start control connection response (SCCRP) and is waiting for the start control connection connected (SCCCN) message cleanup The tunnel is being cleaned up closed The tunnel is being closed destroyed The tunnel is being destroyed established The tunnel is operating terminate The tunnel is terminating Unknown The tunnel is not connected to the router." ::= { jnxL2tpTunnelStatsEntry 9 } jnxL2tpTunnelStatsLocalIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the type of the local end address of this tunnel." ::= { jnxL2tpTunnelStatsEntry 10 } jnxL2tpTunnelStatsLocalIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the local end address of this tunnel." ::= { jnxL2tpTunnelStatsEntry 11 } jnxL2tpTunnelStatsLocalUdpPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the local end UDP port of this tunnel." ::= { jnxL2tpTunnelStatsEntry 12 } jnxL2tpTunnelStatsLocalHostName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the local host name of this tunnel." ::= { jnxL2tpTunnelStatsEntry 13 } jnxL2tpTunnelStatsRemoteHostName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the host name as discovered during the tunnel establishment phase (via the Host Name AVP) of the L2TP peer. If the tunnel is idle this object should maintain its value from the last time it was connected." ::= { jnxL2tpTunnelStatsEntry 14 } jnxL2tpTunnelMaxSessions OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the maximum number of sessions configured on this tunnel. It could be any positive number or unlimited (0)." ::= { jnxL2tpTunnelStatsEntry 15 } jnxL2tpTunnelStatsWindowSize OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the send window size for this tunnel." ::= { jnxL2tpTunnelStatsEntry 16 } jnxL2tpTunnelStatsHelloInterval OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the hello interval for this tunnel." ::= { jnxL2tpTunnelStatsEntry 17 } jnxL2tpTunnelStatsCreationTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time of creation of this tunnel." ::= { jnxL2tpTunnelStatsEntry 18 } jnxL2tpTunnelStatsUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time elapsed since this tunnel was established." ::= { jnxL2tpTunnelStatsEntry 19 } jnxL2tpTunnelStatsIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time elapsed since this tunnel had last data activity (transmission or reception)." ::= { jnxL2tpTunnelStatsEntry 20 } jnxL2tpTunnelStatsCollectionStart OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time at which the statistics gathering started for this tunnel." ::= { jnxL2tpTunnelStatsEntry 21 } jnxL2tpTunnelStatsControlTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of control packets that were transmitted to the tunnel peer." ::= { jnxL2tpTunnelStatsEntry 22 } jnxL2tpTunnelStatsControlTxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of control bytes that were transmitted to the tunnel peer." ::= { jnxL2tpTunnelStatsEntry 23 } jnxL2tpTunnelStatsControlRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of control packets received on the tunnel." ::= { jnxL2tpTunnelStatsEntry 24 } jnxL2tpTunnelStatsControlRxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of control bytes that were received from the tunnel peer." ::= { jnxL2tpTunnelStatsEntry 25 } jnxL2tpTunnelStatsDataTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of data packets transmitted to the tunnel." ::= { jnxL2tpTunnelStatsEntry 26 } jnxL2tpTunnelStatsDataTxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of data bytes that were transmitted to the tunnel peer." ::= { jnxL2tpTunnelStatsEntry 27 } jnxL2tpTunnelStatsDataRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of data packets received from this tunnel." ::= { jnxL2tpTunnelStatsEntry 28 } jnxL2tpTunnelStatsDataRxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of data bytes that were received from the tunnel peer." ::= { jnxL2tpTunnelStatsEntry 29 } jnxL2tpTunnelStatsErrorTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of error transmit packets on the tunnel." ::= { jnxL2tpTunnelStatsEntry 30 } jnxL2tpTunnelStatsErrorRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of error receive packets on the tunnel." ::= { jnxL2tpTunnelStatsEntry 31 } -- -- The L2TP Session Status and Statistics Table -- jnxL2tpSessionStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxL2tpSessionStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP session status and statistics table. This table contains the objects that can be used to describe the current status and statistics of a single L2TP tunneled session." ::= { jnxL2tpObjects 4 } jnxL2tpSessionStatsEntry OBJECT-TYPE SYNTAX JnxL2tpSessionStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An L2TP session interface stats entry." INDEX { jnxL2tpSessionStatsLocalTID, jnxL2tpSessionStatsLocalSID } ::= { jnxL2tpSessionStatsTable 1 } JnxL2tpSessionStatsEntry ::= SEQUENCE { jnxL2tpSessionStatsLocalTID Integer32, jnxL2tpSessionStatsLocalSID Integer32, jnxL2tpSessionStatsServiceInterface SnmpAdminString, jnxL2tpSessionStatsTunnelGroup SnmpAdminString, jnxL2tpSessionStatsRemoteSID Integer32, jnxL2tpSessionStatsInterfaceUnit Integer32, jnxL2tpSessionStatsEncapType INTEGER, jnxL2tpSessionStatsBundleID Integer32, jnxL2tpSessionStatsState INTEGER, jnxL2tpSessionStatsUserName SnmpAdminString, jnxL2tpSessionStatsMode INTEGER, jnxL2tpSessionStatsLocalAddrType InetAddressType, jnxL2tpSessionStatsLocalAddress InetAddress, jnxL2tpSessionStatsLocalUdpPort InetPortNumber, jnxL2tpSessionStatsRemoteAddrType InetAddressType, jnxL2tpSessionStatsRemoteAddress InetAddress, jnxL2tpSessionStatsRemoteUdpPort InetPortNumber, jnxL2tpSessionStatsLocalHostName SnmpAdminString, jnxL2tpSessionStatsRemoteHostName SnmpAdminString, jnxL2tpSessionAssignedIpAddrType InetAddressType, jnxL2tpSessionAssignedIpAddress InetAddress, jnxL2tpSessionLocalMRU INTEGER, jnxL2tpSessionRemoteMRU INTEGER, jnxL2tpSessionStatsTxSpeed Unsigned32, jnxL2tpSessionStatsRxSpeed Unsigned32, jnxL2tpSessionStatsCallBearerType INTEGER, jnxL2tpSessionStatsFramingType INTEGER, jnxL2tpSessionStatsLCPRenegotiation INTEGER, jnxL2tpSessionStatsAuthMethod INTEGER, jnxL2tpSessionStatsNasIpAddrType InetAddressType, jnxL2tpSessionStatsNasIpAddress InetAddress, jnxL2tpSessionStatsNasIpPort InetPortNumber, jnxL2tpSessionStatsFramedProtocol INTEGER, jnxL2tpSessionStatsFramedIpAddrType InetAddressType, jnxL2tpSessionStatsFramedIpAddress InetAddress, jnxL2tpSessionStatsCallingStationID SnmpAdminString, jnxL2tpSessionStatsCalledStationID SnmpAdminString, jnxL2tpSessionStatsAcctDelayTime Integer32, jnxL2tpSessionStatsAcctSessionID SnmpAdminString, jnxL2tpSessionStatsAcctMethod INTEGER, jnxL2tpSessionStatsAcctSessionTime Gauge32, jnxL2tpSessionStatsAcctNasPortType INTEGER, jnxL2tpSessionStatsAcctTnlClientEndPoint Integer32, jnxL2tpSessionStatsAcctTnlServerEndPoint Integer32, jnxL2tpSessionStatsAcctTnlClientAuthID SnmpAdminString, jnxL2tpSessionStatsAcctTnlServerAuthID SnmpAdminString, jnxL2tpSessionStatsUserProfileName SnmpAdminString, jnxL2tpSessionStatsInterfaceID SnmpAdminString, jnxL2tpSessionStatsCallSerialNumber Unsigned32, jnxL2tpSessionStatsCreationTime DateAndTime, jnxL2tpSessionStatsUpTime TimeTicks, jnxL2tpSessionStatsIdleTime TimeTicks, jnxL2tpSessionStatsCollectionStart DateAndTime, jnxL2tpSessionStatsControlTxPkts Counter32, jnxL2tpSessionStatsControlTxBytes Counter64, jnxL2tpSessionStatsControlRxPkts Counter32, jnxL2tpSessionStatsControlRxBytes Counter64, jnxL2tpSessionStatsDataTxPkts Counter32, jnxL2tpSessionStatsDataTxBytes Counter64, jnxL2tpSessionStatsDataRxPkts Counter32, jnxL2tpSessionStatsDataRxBytes Counter64, jnxL2tpSessionStatsErrorTxPkts Counter32, jnxL2tpSessionStatsErrorRxPkts Counter32 } jnxL2tpSessionStatsLocalTID OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains the local tunnel Identifier." REFERENCE "RFC 2661, Section 3.1" ::= { jnxL2tpSessionStatsEntry 1 } jnxL2tpSessionStatsLocalSID OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object contains the local session Identifier." REFERENCE "RFC 2661, Section 3.1" ::= { jnxL2tpSessionStatsEntry 2 } jnxL2tpSessionStatsServiceInterface OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the name of the service interface on which this session is being hosted." ::= { jnxL2tpSessionStatsEntry 3 } jnxL2tpSessionStatsTunnelGroup OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the name of the tunnel group that this session is part of." ::= { jnxL2tpSessionStatsEntry 4 } jnxL2tpSessionStatsRemoteSID OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the remote end assigned session identifier for this session. When a session is starting this value may be zero until the remote tunnel endpoint has responded." REFERENCE "RFC 2661, Section 3.1" ::= { jnxL2tpSessionStatsEntry 5 } jnxL2tpSessionStatsInterfaceUnit OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the interface unit number corresponding to the logical service interface on which the session is being hosted." ::= { jnxL2tpSessionStatsEntry 6 } jnxL2tpSessionStatsEncapType OBJECT-TYPE SYNTAX INTEGER { ppp(1), multilink-ppp(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the tunnel encapsulation type." ::= { jnxL2tpSessionStatsEntry 7 } jnxL2tpSessionStatsBundleID OBJECT-TYPE SYNTAX Integer32 (1..65536) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the bundle that this session is a link of. This field is valid only for tunnel encapsulation type multilink-ppp." ::= { jnxL2tpSessionStatsEntry 8 } jnxL2tpSessionStatsState OBJECT-TYPE SYNTAX INTEGER { established(1), closed(2), destroyed(3), cleanup(4), lns-ic-accept-new(5), lns-ic-idle(6), lns-ic-reject-new(7), lns-ic-wait-connect(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "This field contains the current state of the session - one of the internal session related state names as described below: established The session is operating closed The session is being closed destroyed The session is being destroyed cleanup The session is being cleaned up lns_ic_accept_new A new session is being accepted lns_ic_idle The session has been created and is idle lns_ic_reject_new The new session is being rejected lns_ic_wait_connect The session is waiting for the peer's incoming call connected (ICCN) message." ::= { jnxL2tpSessionStatsEntry 9 } jnxL2tpSessionStatsUserName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the peer session name on this interface. This is typically the login name of the remote user. If the user name is unknown to the local tunnel peer then this object will contain a null string." ::= { jnxL2tpSessionStatsEntry 10 } jnxL2tpSessionStatsMode OBJECT-TYPE SYNTAX INTEGER { shared(1), dedicate(2), unknown(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the configured mode value for this session." ::= { jnxL2tpSessionStatsEntry 11 } jnxL2tpSessionStatsLocalAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the type of the local end address of the tunnel that is hosting this session." ::= { jnxL2tpSessionStatsEntry 12 } jnxL2tpSessionStatsLocalAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the local end address of the tunnel that is hosting this session." ::= { jnxL2tpSessionStatsEntry 13 } jnxL2tpSessionStatsLocalUdpPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the UDP port of the local end of the tunnel that is hosting this session." ::= { jnxL2tpSessionStatsEntry 14 } jnxL2tpSessionStatsRemoteAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the type of the remote end address of the tunnel hosting this session." ::= { jnxL2tpSessionStatsEntry 15 } jnxL2tpSessionStatsRemoteAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the remote end address of the tunnel hosting this session." ::= { jnxL2tpSessionStatsEntry 16 } jnxL2tpSessionStatsRemoteUdpPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the UDP port of the remote end of the tunnel hosting this session." ::= { jnxL2tpSessionStatsEntry 17 } jnxL2tpSessionStatsLocalHostName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the local host name of the tunnel that is hosting this session." ::= { jnxL2tpSessionStatsEntry 18 } jnxL2tpSessionStatsRemoteHostName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the host name as discovered during the tunnel establishment phase (via the Host Name AVP) of the L2TP peer." ::= { jnxL2tpSessionStatsEntry 19 } jnxL2tpSessionAssignedIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the type of IP address of PPP client being tunneled as obtained from IPCP configuration during session establishment." ::= { jnxL2tpSessionStatsEntry 20 } jnxL2tpSessionAssignedIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the IP address of the PPP client being tunneled as obtained from IPCP configuration during session establishment." ::= { jnxL2tpSessionStatsEntry 21 } jnxL2tpSessionLocalMRU OBJECT-TYPE SYNTAX INTEGER(1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The current value of the MRU for the local PPP Entity. This value is the MRU that the remote entity is using when sending packets to this session." ::= { jnxL2tpSessionStatsEntry 22 } jnxL2tpSessionRemoteMRU OBJECT-TYPE SYNTAX INTEGER(1..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "The current value of the MRU for the remote PPP Entity. This value is the MRU that the local entity is using when sending packets to the remote PPP client." ::= { jnxL2tpSessionStatsEntry 23 } jnxL2tpSessionStatsTxSpeed OBJECT-TYPE SYNTAX Unsigned32 UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the last known transmit baud rate for this session." ::= { jnxL2tpSessionStatsEntry 24 } jnxL2tpSessionStatsRxSpeed OBJECT-TYPE SYNTAX Unsigned32 UNITS "bits per second" MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns the last known receive baud rate for this session established." ::= { jnxL2tpSessionStatsEntry 25 } jnxL2tpSessionStatsCallBearerType OBJECT-TYPE SYNTAX INTEGER { none(1), digital(2), analog(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the bearer type of this session." ::= { jnxL2tpSessionStatsEntry 26 } jnxL2tpSessionStatsFramingType OBJECT-TYPE SYNTAX INTEGER { none(1), sync(2), async(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes the framing type of this session." ::= { jnxL2tpSessionStatsEntry 27 } jnxL2tpSessionStatsLCPRenegotiation OBJECT-TYPE SYNTAX INTEGER { off(1), on(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object returns whether LCP renegotiation is on or off for this session." ::= { jnxL2tpSessionStatsEntry 28 } jnxL2tpSessionStatsAuthMethod OBJECT-TYPE SYNTAX INTEGER { none(1), text(2), pppChap(3), pppPap(4), pppEap(5), pppMsChapV1(6), pppMsChapV2(7), other(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the proxy authentication method employed by the LAC for the session." ::= { jnxL2tpSessionStatsEntry 29 } jnxL2tpSessionStatsNasIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the type of IP address of the RADIUS network address server to which the accounting records for this session are being sent to." ::= { jnxL2tpSessionStatsEntry 30 } jnxL2tpSessionStatsNasIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the IP address of the RADIUS network address server to which the accounting records for this session are being sent to." ::= { jnxL2tpSessionStatsEntry 31 } jnxL2tpSessionStatsNasIpPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the port on which RADIUS network address server accounting messages will be sent." ::= { jnxL2tpSessionStatsEntry 32 } jnxL2tpSessionStatsFramedProtocol OBJECT-TYPE SYNTAX INTEGER { ppp(1), slip(2), arap(3), gandalf(4), xylogicsIPX-SLIP(5), x75-sync(6), none(100) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the frame protocol attribute obtained from RADIUS server for this session." REFERENCE "RFC 2865, Section 5.7" ::= { jnxL2tpSessionStatsEntry 33 } jnxL2tpSessionStatsFramedIpAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This Attribute indicates the type of address to be configured for the user, as provided by the RADIUS server in response to authentication request." REFERENCE "RFC 2865, Section 5.8" ::= { jnxL2tpSessionStatsEntry 34 } jnxL2tpSessionStatsFramedIpAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This Attribute indicates the address to be configured for the user, as provided by the RADIUS server in response to authentication request." REFERENCE "RFC 2865, Section 5.8" ::= { jnxL2tpSessionStatsEntry 35 } jnxL2tpSessionStatsCallingStationID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This Attribute allows the RADIUS NAS to send in the Access-Request packet the phone number that the call came from, using Automatic Number Identification (ANI) or similar technology. It is only used in Access-Request packets." REFERENCE "RFC 2865, Section 5.31" ::= { jnxL2tpSessionStatsEntry 36 } jnxL2tpSessionStatsCalledStationID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This Attribute allows the RADIUS NAS to send in the Access-Request packet the phone number that the user called, using Dialed Number Identification (DNIS) or similar technology. It is only used in Access-Request packets." REFERENCE "RFC 2865, Section 5.30" ::= { jnxL2tpSessionStatsEntry 37 } jnxL2tpSessionStatsAcctDelayTime OBJECT-TYPE SYNTAX Integer32(0..64) MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates how many seconds the RADIUS accounting client has been trying to send a record for, and can be subtracted from the time of arrival on the server to find the approximate time of the event generating this Accounting-Request." REFERENCE "RFC 2866, Section 5.2" ::= { jnxL2tpSessionStatsEntry 38 } jnxL2tpSessionStatsAcctSessionID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is a unique Accounting ID to make it easy to match start and stop records in a log file." REFERENCE "RFC 2866, Section 5.5" ::= { jnxL2tpSessionStatsEntry 39 } jnxL2tpSessionStatsAcctMethod OBJECT-TYPE SYNTAX INTEGER { radius(1), local(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the accounting method employed for this session." ::= { jnxL2tpSessionStatsEntry 40 } jnxL2tpSessionStatsAcctSessionTime OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute indicates how many seconds the user has received service for." REFERENCE "RFC 2866, Section 5.7" ::= { jnxL2tpSessionStatsEntry 41 } jnxL2tpSessionStatsAcctNasPortType OBJECT-TYPE SYNTAX INTEGER { async(1), sync(2), isdn-sync(3), isdn-asunc-v-120(4), isdn-async-v-110(5), virtual(6), piafs(7), hdlc-clear-channel(8), x-25(9), x-75(10), g-3-fax(11), sdsl(12), adsl-cap(13), adsl-dmt(14), idsl(15), ethernet(16), xdsl(17), cable(18), wireless-other(19), wireless-ieee-802-1(20) } MAX-ACCESS read-only STATUS current DESCRIPTION "This Attribute indicates the type of the physical port of the NAS which is performing accounting for the user." REFERENCE "RFC 2865, Section 5.41" ::= { jnxL2tpSessionStatsEntry 42 } jnxL2tpSessionStatsAcctTnlClientEndPoint OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the remote tunnel Identifier of the tunnel hosting this session." REFERENCE "RFC 2661, Section 3.1" ::= { jnxL2tpSessionStatsEntry 43 } jnxL2tpSessionStatsAcctTnlServerEndPoint OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the local tunnel Identifier of the tunnel hosting this session." REFERENCE "RFC 2661, Section 3.1" ::= { jnxL2tpSessionStatsEntry 44 } jnxL2tpSessionStatsAcctTnlClientAuthID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the host name as discovered during the tunnel establishment phase (via the Host Name AVP) of the L2TP peer, for the tunnel that is hosting this session." ::= { jnxL2tpSessionStatsEntry 45 } jnxL2tpSessionStatsAcctTnlServerAuthID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the local host name of the tunnel that is hosting this session." ::= { jnxL2tpSessionStatsEntry 46 } jnxL2tpSessionStatsUserProfileName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the configured access profile name that is being used for this session." ::= { jnxL2tpSessionStatsEntry 47 } jnxL2tpSessionStatsInterfaceID OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the interface identification (name) for the session bearing service interface." ::= { jnxL2tpSessionStatsEntry 48 } jnxL2tpSessionStatsCallSerialNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the serial number that has been assigned to this session." ::= { jnxL2tpSessionStatsEntry 49 } jnxL2tpSessionStatsCreationTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time of creation of this session." ::= { jnxL2tpSessionStatsEntry 50 } jnxL2tpSessionStatsUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time elapsed since this session was established." ::= { jnxL2tpSessionStatsEntry 51 } jnxL2tpSessionStatsIdleTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time elapsed since this session had last data activity (transmission or reception)." ::= { jnxL2tpSessionStatsEntry 52 } jnxL2tpSessionStatsCollectionStart OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "This object represents the time at which the statistics gathering started for this session." ::= { jnxL2tpSessionStatsEntry 53 } jnxL2tpSessionStatsControlTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of control packets that were transmitted to the session peer." ::= { jnxL2tpSessionStatsEntry 54 } jnxL2tpSessionStatsControlTxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of control bytes that were transmitted to the session peer." ::= { jnxL2tpSessionStatsEntry 55 } jnxL2tpSessionStatsControlRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of control packets received on the session." ::= { jnxL2tpSessionStatsEntry 56 } jnxL2tpSessionStatsControlRxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of control bytes that were received from the session peer." ::= { jnxL2tpSessionStatsEntry 57 } jnxL2tpSessionStatsDataTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of data packets transmitted to the remote session peer." ::= { jnxL2tpSessionStatsEntry 58 } jnxL2tpSessionStatsDataTxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of data bytes that were transmitted to the session peer." ::= { jnxL2tpSessionStatsEntry 59 } jnxL2tpSessionStatsDataRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of data packets received on this session." ::= { jnxL2tpSessionStatsEntry 60 } jnxL2tpSessionStatsDataRxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of data bytes that were received from the session peer." ::= { jnxL2tpSessionStatsEntry 61 } jnxL2tpSessionStatsErrorTxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of error transmit packets on the session." ::= { jnxL2tpSessionStatsEntry 62 } jnxL2tpSessionStatsErrorRxPkts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the number of error receive packets on the session." ::= { jnxL2tpSessionStatsEntry 63 } -- -- The L2TP Multilink PPP bundle statistics table -- jnxL2tpMlpppBundleStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF JnxL2tpMlpppBundleStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP MLPPP bundle status and statistics table. This table contains the objects that can be used to describe the current status and statistics of a single L2TP tunneled multilink PPP bundle." ::= { jnxL2tpObjects 5 } jnxL2tpMlpppBundleStatsEntry OBJECT-TYPE SYNTAX JnxL2tpMlpppBundleStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An L2TP MLPPP bundle statistics entry." INDEX { jnxL2tpMlpppBundleStatsBundleID } ::= { jnxL2tpMlpppBundleStatsTable 1 } JnxL2tpMlpppBundleStatsEntry ::= SEQUENCE { jnxL2tpMlpppBundleStatsBundleID Integer32, jnxL2tpMlpppBundleStatsNumLinks Integer32, jnxL2tpMlpppBundleStatsEndpoint SnmpAdminString, jnxL2tpMlpppBundleStatsInputMrru Integer32, jnxL2tpMlpppBundleStatsOutputMrru Integer32 } jnxL2tpMlpppBundleStatsBundleID OBJECT-TYPE SYNTAX Integer32 (1..65536) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the session's associated bundle." ::= { jnxL2tpMlpppBundleStatsEntry 1 } jnxL2tpMlpppBundleStatsNumLinks OBJECT-TYPE SYNTAX Integer32 (1..8) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the current number of links that have joined the bundle." ::= { jnxL2tpMlpppBundleStatsEntry 2 } jnxL2tpMlpppBundleStatsEndpoint OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the username of the MLPPP bundle." ::= { jnxL2tpMlpppBundleStatsEntry 3 } jnxL2tpMlpppBundleStatsInputMrru OBJECT-TYPE SYNTAX Integer32 (64..4500) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the maximum packet size that the input inteface can process." ::= { jnxL2tpMlpppBundleStatsEntry 4 } jnxL2tpMlpppBundleStatsOutputMrru OBJECT-TYPE SYNTAX Integer32 (64..4500) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the maximum packet size that the output interface can process." ::= { jnxL2tpMlpppBundleStatsEntry 5 } END