Configuring Basic Settings with J-Web Quick Configuration

J-Web Quick Configuration allows you to configure basic settings. Figure 8 shows the Quick Configuration page for basic setup.

Figure 8: Set Up Quick Configuration Page

Set Up Quick Configuration Page

Before you configure the device, gather the information described in Before You Begin.

To configure basic settings with J-Web Quick Configuration:

If the Set Up Quick Configuration page is not displayed, select Configuration>Quick Configuration >Set Up.
Enter information into the Set Up Quick Configuration page, as described in Table 96.

Click one of the following buttons:

To apply the configuration and stay in the Set Up Quick Configuration page, click Apply.
To apply the configuration and return to the Quick Configuration page, click OK.
To cancel your entries and return to the Quick Configuration page, click Cancel.

Note: After initial configuration is complete, the Services Router stops functioning as a DHCP server. If you change the IP address of ge-0/0/0 or fe-0/0/0 and have the management device configured to use DHCP, you lose your DHCP lease and your connection to the router through the J-Web interface. To reestablish a connection, either set the IP address on the management device manually, or connect ge-0/0/0 or fe-0/0/0 to the management network and access the router another way—for example, through the console port.

To check the configuration, see .

Table 96: Set Up Quick Configuration Summary

Field	Function	Your Action
Identification
Host Name (required)	Defines the hostname of the device.	Type the hostname.
Domain Name	Defines the network or subnetwork that the machine belongs to.	Type the domain name.
Root Password (required)	Sets the root password that user “root” can use to log in to the device.	Type a plain-text password that the system encrypts. Note: After a root password has been defined, it is required when you log in to the J-Web user interface or the CLI.
Verify Root Password (required)	Verifies the root password has been typed correctly.	Retype the password.
Time
Time Zone	Identifies the time zone that the device is located in.	From the list, select the appropriate time zone.
NTP Servers	Specify an NTP server that the device can reach to synchronize the system time.	To add an IP address, type it in the box to the left of the Add button, then click Add. To delete an IP address, click on it in the box above the Add button, then click Delete.
Current System Time	Synchronizes the system time with the NTP server, or manually set the system time and date.	To immediately set the time using the NTP server, click Set Time via NTP. The device sends a request to the NTP server and synchronizes the system time. Note: If you are configuring other settings on this page, the device also synchronizes the system time using the NTP server when you click Apply or OK. To set the time manually, click Set Time Manually. A pop-up window allows you to select the current date and time from lists.
Network
DNS Name Servers	Specify a DNS server that the device can use to resolve hostnames into addresses.	To add an IP address, type it in the box to the left of the Add button, then click Add. To delete an IP address, click on it in the box above the Add button, then click Delete.
Domain Search	Adds each domain name that the device is included in to the configuration so that they are included in a DNS search.	To add a domain name, type it in the box to the left of the Add button, then click Add. To delete a domain name, click on it in the box above the Add button, then click Delete.
Default Gateway	Defines a default gateway through which to direct packets addressed to networks not explicitly listed in the routing table.	Type a 32-bit IP address, in dotted decimal notation.
Loopback Address	Defines a reserved IP address that is always available on the device. If no address is entered, this address is set to 127.0.0.1/32.	Type a 32-bit IP address and prefix length, in dotted decimal notation.
ge-0/0/0 or fe-0/0/0 Address	Defines the IP address and prefix length of ge-0/0/0 or fe-0/0/0. The interface ge-0/0/0 or fe-0/0/0 is typically used as the management interface for accessing the device. The DHCP client sets this address to 192.168.1.1/24 if no DHCP server is found.	Type a 32-bit IP address and prefix length, in dotted decimal notation. Note: You must enter the ge-0/0/0 or fe-0/0/0 address on the Quick Configuration Set Up page before you click Apply or OK. If you do not manually configure this address, you will lose your connection to the J-Web interface when you click Apply or OK.
Management Access
Allow Telnet Access	Allows remote access to the device using Telnet.	To enable Telnet access, select the check box.
Allow JUNOScript over Clear-Text Access	Allows JUNOScript to access the device using a protocol for sending unencrypted text over a TCP connection.	To enable JUNOScript access over clear text, select the check box.
Allow SSH Access	Allows remote access to the device using SSH.	To enable SSH access, select the check box.

[Report an Error]