Configuring an ATM-over-ADSL Interface with Quick Configuration

The Quick Configuration pages allow you to configure ATM-over-ADSL interfaces on J Series devices.

Table 136: ATM-over-ADSL Interface Quick Configuration Pages Summary

Field	Function	Your Action
Configuring Logical Interfaces
Logical Interfaces	Lists the logical interfaces for this ATM-over-ADSL physical interface.	To add a logical interface, click Add. To edit a logical interface, select the interface from the list. To delete a logical interface, select the check box next to the name and click Delete.
Adding or Editing a Logical Interface
Add logical interfaces	Defines one or more logical units that you connect to this physical ADSL interface.	Click Add.
Logical Interface Description	(Optional) Describes the logical interface.	Type a text description of the logical interface to more clearly identify it in monitoring displays.
Encapsulation	Specifies the type of encapsulation on the DSL logical interface.	From the list, select one of the following types of encapsulations. For ATM-over-ADSL interfaces that use inet (IPv4) protocols only, select one of the following: ATM VC multiplexing—Use ATM virtual circuit multiplex encapsulation. ATM NLPID—Use ATM network layer protocol identifier (NLPID) encapsulation. Cisco-compatible ATM NLPID—Use Cisco NLPID encapsulation. Ethernet over ATM (LLC/SNAP)—For interfaces that carry IPv4 traffic, use Ethernet over logical link control (LLC) encapsulation. You cannot configure multipoint interfaces if you use this type of encapsulation. For ATM-over-ADSL for PPP-over-ATM (PPPoA) interfaces only, select one of the following: ATM PPP over AAL5/LLC—Use AAL5 logical link control (LLC) encapsulation. ATM PPP over Raw AAL5—Use AAL5 multiplex encapsulation. For other encapsulation types on the ATM-over-ADSL interfaces, select one of the following: PPPoE over ATM (LLC/SNAP)—Use PPP over Ethernet over ATM LLC encapsulation. When you use this encapsulation type, you cannot configure the interface address. Instead you configure the interface address on the PPP interface. Ethernet over ATM (LLC/SNAP)—Use ATM subnetwork attachment point (SNAP) encapsulation.
VCI	Configures the ATM virtual circuit identifier (VCI) for the interface.	In the VCI box, type the number for the VCI.
Add IPv4 address prefixes and destinations	Specifies one or more IPv4 addresses and destination addresses.	Click Add.
IPv4 Address Prefix	Specifies an IPv4 address for the interface.	Type an IPv4 address and prefix. For example: 10.10.10.10/24
Destination Address	Specifies the destination address.	Type an IPv4 address for the destination. Click OK.
Configuring Physical Interface Properties
Physical Interface Description	(Optional) Adds supplementary information about the physical ATM-over-ADSL interface.	Type a text description of the physical ATM-over-ADSL interface to more clearly identify it in monitoring displays. Specify that it is an ADSL interface.
MTU (bytes)	Specifies the maximum transmit size of a packet for the ATM-over-ADSL interface.	Type a value from 256 to 9192.
Encapsulation	Selects the type of encapsulation for traffic on this physical interface.	From the list, select the type of encapsulation for this ATM-over-ADSL interface: ATM permanent virtual circuits—Use this type of encapsulation for PPP over ATM (PPPoA) over ADSL interfaces. This is the default encapsulation for ATM-over-ADSL interfaces. Ethernet over ATM encapsulation—Use this type of encapsulation for PPP over Ethernet (PPPoE) over ATM-over-ADSL interfaces that carry IPv4 traffic.
VPI	Configures the ATM virtual path identifier for the interface.	Type a VPI value between 0 and 255.
Configuring ADSL Options
Operating Mode	Specifies the type of DSL operating mode for the ATM-over-ADSL interface.	From the list, select one of the following types of DSL operating modes—for example auto. For Annex A or Annex B, or Annex M (applicable to SRX210 devices), select one of the following: auto—Configure the ADSL interface to auto negotiate settings with the DSLAM located at the central office. For Annex A, the ADSL interface trains in either ANSI T1.413 Issue II mode or ITU G.992.1 mode. For Annex B, the ADSL interface trains in ITU G.992.1 mode. For Annex M, the ADSL interface trains in ITU G.992.3 mode (applicable to SRX210 devices). itu-dmt-bis—Configure the ADSL interface to train in ITU G.992.3 mode. The ADSL interface trains in ITU G.992.5 mode. adsl2plus—Configure the ADSL interface to train in ITU G.992.5 mode. You can configure this mode only when it is supported on the DSLAM. For Annex A and Annex B, select the following: itu-dmt—Configure the ADSL interface to train in ITU G.992.1 mode. adsl2plus—Configure the ADSL interface to train in ITU G.992.5 mode. You can configure this mode only when it is supported on the DSLAM. itu-dmt-bis—Configure the ADSL interface to train in ITU G.992.3 mode. The ADSL interface trains in ITU G.992.5 mode. For Annex A only, select the following: ansi-dmt—Configure the ADSL interface to train in the ANSI T1.413 Issue II mode. For Annex B only, select the following: itu-annexb-ur2—Configure the ADSL line to train in the G.992.1 Deutsche Telekom UR-2 mode.