[Prev][Next][Report an Error]

2-Port 10 Gigabit Ethernet XPIM Configuration Page Options

Table 110 describes the available options for the 2-Port 10 Gigabit XPIM configuration page.

Table 110: Configuring the 2-Port 10 Gigabit Ethernet XPIM Using J-Web

Field

Action

Function

Logical Interfaces

Add logical interfaces

Click Add

Defines one or more logical units that you connect to this physical Gigabit Ethernet interface. You must define at least one logical unit for a Gigabit Ethernet interface.

Logical Interface (Optional)

Enter logical interface description.

Describes the logical interface.

IPv4 Addresses Prefixes

  1. Type one or more IPv4 addresses and prefixes.

    For example: 10.10.10.10/24

  2. Click Add.
  3. Click OK.

To delete an IP address and prefix, select them in the Source Addresses and Prefixes box, then click Delete.

Specifies one or more IPv4 addresses for the interface.

ARP Address

Type an IPv4 address that you want to associate with the media access control (MAC) address—for example, 10.10.10.1.

Enables the device to create a static Address Resolution Protocol (ARP) entry for this interface by specifying the IP address of a node to associate with its MAC address.

The IP address must be in the same subnet as the IPv4 address or prefix of the interface you are configuring. Static ARP entries associate the IP addresses and MAC addresses of nodes on the same subnet, enabling a device to respond to ARP requests having destination addresses that are not local to the incoming interface.

MAC Address

Type the MAC address to be mapped to the ARP entry—for example, 00:12:1E:A9:8A:80.

Specifies the hardware MAC address associated with the ARP address.

The MAC address uniquely identifies the system and is expressed in the following format: mm:mm:mm:ss:ss:ss.

The first three octets denote the hardware manufacturer ID, and the last three are serial numbers identifying the device.

Publish

  • To enable publishing, select the check box.
  • To disable publishing, clear the check box.

Enables the device to reply to ARP requests for the specified address.

Enable Ethernet Switching

  • To enable Ethernet switching, select the check box.
  • To disable Ethernet switching, clear the check box.

Enables or disables Ethernet switching.

Port Mode

Select one of the following:

  • Trunk
  • Access

Specifies the mode of operation for the port.

Native VLAN Id

Enter a valid VLAN name or VLAN tag.

VLAN identifier to associate with untagged packets received on the interface.

Physical Interface Description (Optional)

Type a text description of the Gigabit Ethernet interface to more clearly identify it in monitoring displays.

Adds supplementary information about the physical Gigabit Ethernet interface.

MTU (bytes)

Type a value between 256 and 9216 bytes.

Default MTU: 1514

Specifies the maximum transmission unit (MTU) size for the Gigabit Ethernet interface.

Per unit scheduler

  • To enable scheduling, select the check box.
  • To disable scheduling, clear the check box.

Enables scheduling on logical interfaces.

This option allows you to configure multiple output queues on a logical interface and associate an output scheduler and shaping rate with the queues.

Framing Mode

Framing Mode

Select one of the following:

  • LAN-mode
  • WAN-mode

Specifies the framing mode.

Loopback Mode

Select one of the following:

  • Local
  • Remote

Specifies the loopback mode.

Path Trace

Enter a text string.

Identifies the circuit.

Gigabit Ethernet Options

Loopback

  • Select Yes to enable the loopback diagnostic option.
  • Select No to disable the loopback option.

    By default, loopback is disabled.

Enables or disables the loopback option.

Auto Negotiation

  • Select Yes to enable autonegotiation.
  • Select No to disable autonegotiation.

    By default, autonegotiation is enabled.

Enables or disables autonegotiation.

By default, Gigabit Ethernet interfaces autonegotiate the link mode and speed settings. If you disable autonegotiation and do not manually configure link mode and speed, the link is negotiated at 1000 Mbps, full duplex. When you configure both the link mode and the speed, the link negotiates with the manually configured settings whether autonegotiation is enabled or disabled.

Auto Negotiation Remote Fault

Select the autonegotation remote fault value from the list of options given.

  • local-interface-offline
  • local-interface-offline

This field is enabled only if autonegotiation is enabled.

Indicates the autonegotiation remote fault value.

Source MAC Address Filters

To add MAC addresses, type them in the boxes above the Add button, then click Add.

To delete a MAC address, select it in the Source Addresses box, then click Delete.

Displays the list of MAC addresses from which you want to receive packets on this interface.

Redundant Parent

Enter a redundant Ethernet interface name.

Specifies the name of the redundant Ethernet interface that a physical interface is associated with to form a redundant Ethernet interface pair.

802.3ad

Enter an aggregated Ethernet logical interface name.

Enables you to group Ethernet interfaces at the Physical Layer to form a single link layer interface.

Tag Protocol ID

Enter standard Tag Protocol Identifier (TPID) values.

Identifies the frame as an IEEE 802.1Q-tagged frame.

MAC Learning

  • Select Yes to enable MAC Learning.
  • Select No to disable MAC Learning.

Enables or disabling dynamic source MAC addresses.


[Prev][Next][Report an Error]