[Prev][Next][Report an Error]

Configuring PPPoE Interfaces with Quick Configuration

To configure properties on a PPPoE interface:

  1. In the J-Web user interface, select Configuration>Quick Configuration>Interfaces.

    A list of the network interfaces present on the device is displayed, as shown in Figure 7. (For information about interface names, see the JUNOS Enhanced Services Interfaces and Routing Configuration Guide.) The third column indicates whether the interface has been configured.

  2. Select pp0.

    The PPPoE Interfaces Quick Configuration main page is displayed, as shown in Figure 18.

    Figure 18: PPPoE Interfaces Quick Configuration Main Page

    PPPoE Interfaces Quick Configuration
Main Page

  3. Enter information into the Quick Configuration pages, as described in Table 96.
  4. From the PPPoE Interfaces Quick Configuration main page, click one of the following buttons:
  5. To verify that the PPPoE interface is configured correctly, see the JUNOS Enhanced Services Interfaces and Routing Configuration Guide.

Table 96: PPPoE Quick Configuration Summary

Field

Function

Your Action

Logical Interfaces

Logical Interfaces

Lists the logical interfaces for the PPPoE physical interface.

  • To add a logical interface, click Add.
  • To edit a logical interface, select the interface from the list.
  • To delete a logical interface, select the check box next to the name and click Delete.

Add logical interfaces

Defines one or more logical units that you connect to this physical PPPoE interface. You must define at least one logical unit for a PPPoE interface.

Click Add.

Logical Interface Description

(Optional) Describes the logical interface.

Type a text description of the logical interface to more clearly identify it in monitoring displays.

IPv4 Addresses and Prefixes

Specifies one or more IPv4 addresses for the interface.

  1. Type one or more IPv4 addresses and prefixes. For example:

    10.10.10.10/24

  2. Click Add.
  3. Click OK.

Physical Interface Description

(Optional) Adds supplementary information about the physical PPPoE interface.

Type a text description of the PPPoE interface to more clearly identify it in monitoring displays.

PPP Options

Enable CHAP

Enables or disables CHAP authentication on a PPPoE interface.

  • To enable CHAP, select the check box.
  • To disable CHAP, clear the check box.
CHAP Local Identity (available if CHAP is enabled)

Use System Host Name

Specifies that the PPPoE interface uses the device's system hostname in CHAP challenge and response packets.

  • To enable, select the check box (the default).
  • To disable, clear the check box.

Local Name

If Use System Host Name is disabled, specifies the local name for CHAP to use.

Type a local name for this PPPoE interface.

CHAP Peer Identity (required if CHAP is enabled)

Identifies the client or peer with which the device communicates on this PPPoE interface.

Type the CHAP client name.

CHAP Secret (required if CHAP is enabled)

Specifies the secret password for CHAP authentication, known to both sides of the connection.

Type a password that is known to the other side of the connection. Use a combination of letters and numbers that is difficult for others to guess.

PPPoE Options

Access Concentrator

Identifies the access concentrator by a unique name.

Type a name for the access concentrator—for example, ispl.com.

Auto Reconnect Time

Specifies the number of seconds to wait before reconnecting after a PPPoE session is terminated.

Type a value from 1 through 4294947295 for automatic reconnection—for example, 100 seconds. Type 0 (the default) for immediate reconnection.

Idle Timeout

Specifies the number of seconds a session can be idle without disconnecting.

Type a value for the timeout. Type 0 if you do not want the session to time out.

Service Name

Identifies the type of service provided by the access concentrator, such as the name of the Internet service provider (ISP), class, or quality of service.

Type the type of service provided by the access concentrator. For example, video@ispl.com.

Underlying Interface

Specifies the logical Ethernet interface or the logical ATM interface as the underlying interface for the PPPoE session.

From the list, select the underlying interface for the PPPoE session—for example, ge-0/0/1.0 or at-2/0/0.0.

For information about interface names, see the JUNOS Enhanced Services Interfaces and Routing Configuration Guide.


[Prev][Next][Report an Error]