[ Contents] [ Prev] [ Next] [ Report an Error]

SONET/SDH OC48/STM16 (Multi-Rate) PIC with SFP

Image g003906.gif

Software release
  • JUNOS 8.3 and later (Type 2)
Description
  • Rate-selectable using one of the following rates:
    • 1-port OC3c
    • 1-port OC12
    • 1-port OC12c
    • 1-port OC48
    • 1-port OC48c
  • Power requirement: 0.20 A @ 48 V (9.5 W)
Hardware features
  • Multiplexing and demultiplexing
  • Rate policing on input
  • Rate shaping on output
  • Packet buffering, Layer 2 parsing
Software features
  • Optical diagnostics and related alarms
  • Per-port SONET/SDH framing
  • Link aggregation
  • Alarm and event counting and detection
  • Dual-router automatic protection switching (APS)
  • Multiprotocol Label Switching (MPLS) fast reroute
  • Encapsulations:
    • Circuit cross-connect (CCC)
    • Translational cross-connect (TCC)
    • Frame Relay
    • High-Level Data Link Control (HDLC)
    • Point-to-Point Protocol (PPP)
Cables and connectorsYou can install any transceiver supported by the PIC. For information about installing and removing transceivers, see the PIC and Transceiver Installation Instructions. To extend the life of the laser, when a PIC is not being actively used with any valid links, take the PIC offline until you are ready to establish a link to another device. For information about taking a PIC offline, see the request chassis pic offline command in the JUNOS System Basics and Services Command Reference.
LEDsOne tricolor per port:
  • Off—Not enabled
  • Green—Online with no alarms or failures
  • Amber—Online with alarms for remote failures
  • Red—Active with a local alarm; router has detected a failure
Alarms, errors, and events
  • SONET alarms:
    • Alarm indication signal—line (AIS-L)
    • Alarm indication signal—path (AIS-P)
    • Bit error rate—signal degrade (BERR-SD)
    • Bit error rate—signal fail (BERR-SF)
    • Bit interleaved parity (BIP) error B1, B2, B3
    • Far-end bit error: remote error indication—line (REI-L), far-end line coding violations (CV-LFE)
    • Far-end bit error: remote error indication—path (REI-P), far-end path coding violations (CV-PFE)
    • Loss of frame (LOF)
    • Loss of pointer (LOP-P)
    • Loss of signal (LOS)
    • Payload label mismatch (PLM-P)
    • Payload unequipped (unequipped STS at path level) (UNEQ-P)
    • Remote defect indication—line (RDI-L)
    • Remote defect indication—path (RDI-P)
  • SDH alarms:
    • Administrative unit alarm indication signal (AU-AIS)
    • Bit error rate signal degrade (BERR-SD)
    • Bit error rate signal fail (BERR-SF)
    • Bit interleaved parity (BIP) error B1, B2, B3
    • Higher order path—payload label mismatch (HP-PLM)
    • Higher order path—loss of pointer (HP-LOP)
    • Higher order path—remote defect indication (HP-RDI)
    • Higher order path—unequipped (HP-UNEQ)
    • Loss of frame (LOF)
    • Loss of signal (LOS)
    • Multiplex section—alarm indication signal (MS-AIS)
    • Multiplex section—remote defect indication (MS-RDI)
    • Multiplex section—remote error indication (MS-REI)
  • Error detection:
    • Errored seconds (ES-S, ES-L, ES-P)
    • Far-end errored seconds (ES-LFE, ES-PFE)
    • Far-end severely errored seconds (SES-LFE, SES-PFE)
    • Far-end unavailable seconds (UAS-LFE, UAS-PFE)
    • Severely errored framing (SEF)
    • Severely errored framing seconds (SEFS-S)
    • Severely errored seconds (SES-S, SES-L, SES-P)
    • Unavailable seconds (UAS-L, UAS-P)

Table 31: Optical Interface Support for SONET/SDH OC48/STM16 (Multi-Rate) PICs Configured at an OC3/STM1 Rate

ParameterMultimodeIntermediate Reach (IR-1)Long Reach (LR-1)
Transceiver model numberSFP-1OC3-SRSFP-1OC3-IRSFP-1OC3-LR
Optical interfaceMultimodeSingle-modeSingle-mode
Transceiver typeSFPSFPSFP
Maximum distanceMMF cable: 1.2 miles/2 km SMF cable: 9.3 miles/15 kmSMF cable: 24.85 miles/40 km
StandardMultivendor agreementTelcordia GR-253 Telcordia GR-253
Transmitter wavelength1270 through 1380 nm1261 through 1360 nm 1263 through 1360 nm
Average launch power–20 through –14 dBm–15 through –8 dBm–5 through 0 dBm
Receiver saturation–14 dBm–8 dBm–10 dBm
Receiver sensitivity–30 dBm–28 dBm–34 dBm

Table 32: Optical Interface Support for SONET/SDH OC48/STM16 (Multi-Rate) PICs Configured at an OC12/STM4 Rate

ParameterShort Reach (SR-1) Intermediate Reach (IR-1) Long Reach (LR-1)
Transceiver model numberSFP-1OC12-SRSFP-1OC12-IRSFP-1OC12-LR
Optical interfaceSingle-mode Single-mode Single-mode
Transceiver typeSFPSFPSFP
Maximum distanceSMF cable: 1.24 miles/2 kmSMF cable: 9.3 miles/15 kmSMF cable: 24.85 miles/40 km
StandardTelcordia GR-253 Telcordia GR-253 Telcordia GR-253
Transmitter wavelength1261 through 1360 nm1274 through 1356 nm 1280 through 1335 nm
Average launch power–15 through –8 dBm–15 through –8 dBm–3 through +2 dBm
Receiver saturation–8 dBm–8 dBm–8 dBm
Receiver sensitivity–23 dBm–28 dBm–28 dBm

Table 33: Optical Interface Support for SONET/SDH OC48/STM16 (Multi-Rate) PICs Configured at an OC48/STM16 Rate

ParameterShort Reach (SR-1) Intermediate Reach (IR-1) Long Reach (LR-2)
Transceiver model numberSFP-OC48-SRSFP-OC48-IRSFP-OC48-LR
Optical interfaceSingle-mode Single-mode Single-mode
Transceiver typeSFPSFPSFP
Maximum distanceSMF cable: 1.24 miles/2 kmSMF cable: 9.3 miles/15 kmSMF cable: 49.71 miles/80 km
StandardTelcordia GR-253 Telcordia GR-253 Telcordia GR-253
Transmitter wavelength1266 through 1360 nm1260 through 1360 nm 1500 through 1580 nm
Average launch power–10 through –3 dBm–5 through 0 dBm–2 through +3 dBm
Receiver saturation–3 dBm0 dBm–9 dBm
Receiver sensitivity–18 dBm–18 dBm–28 dBm

[ Contents] [ Prev] [ Next] [ Report an Error]