[ Contents] [ Prev] [ Next] [ Report an Error]

Channelized OC3 IQ PIC

Image g002197.gif

Software release

JUNOS 7.1 and later (Type 1)

Description

One OC3 port

Power requirement: 0.39 A @ 48 V (18.6 W)

Fine-grained queuing per logical interface

Channelization: DS3, DS1, DS0

Hardware features

Subrate and scrambling:

Digital Link/Quick Eagle

Kentrox

Larscom

ADTRAN

Verilink

Packet buffering, Layer 2 parsing

M13/C-bit parity encoding

DS3 far-end alarm and control (FEAC) channel support

Local and remote loopback testing

Software features

Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED)

Simple Network Management Protocol (SNMP): OC3 MIB, DS3 MIB, T1 MIB

Dynamic, arbitrary channel configuration

Full bit error rate test (BERT)

Encapsulations:

Circuit cross-connect (CCC)

Translational cross-connect (TCC)

Frame Relay

High-Level Data Link Control (HDLC)

Point-to-Point Protocol (PPP)

Cables and connectors

Duplex SC/PC connector (Rx and Tx); single-mode fiber intermediate-reach fiber

LEDs One tricolor per port:

Off—Not enabled

Green—Online with no alarms or failures

Amber—Online with alarms for remote failures

Red—Active with a local alarm; router has detected a failure

Alarms, errors, and events Alarms:

Alarm indication signal—line (AIS-L)

Alarm indication signal—path (AIS-P)

Bit error rate signal degrade (BERR-SD)

Bit error rate signal fail (BERR-SF)

Idle code, idle received

Loss of frame (LOF)

Loss of pointer (LOP-P)

Loss of signal (LOS)

Out of frame (OOF)

Payload mismatch (PLM-P)

Payload unequipped (unequipped STS at path level) (UNEQ-P)

Parity bit (P-bit) disagreements

Path parity error

Remote defect indication—line (RDI-L)

Remote defect indication—path (RDI-P)

Yellow alarm bit (X-bit) disagreements

Error detection:

Bit interleaved parity errors B1, B2, B3 (CV-S, CV-L, CV-P)

Errored seconds (ES-S, ES-L, ES-P)

Far-end bit errors, remote error indication—line (REI-L), far-end line coding violations (CV-LFE)

Far-end bit errors, remote error indication—path (REI-P), far-end path coding violations (CV-PFE)

Far-end block error (FEBE)

Far-end errored seconds (ES-LFE, ES-PFE)

Far-end severely errored seconds (SES-LFE, SES-PFE)

Far-end unavailable seconds (UAS-LFE, UAS-PFE)

Frame error

Severely errored framing (SEF)

Severely errored framing seconds (SEFS-S)

Severely errored seconds (SES-S, SES-L, SES-P)

Unavailable seconds (UAS-L, UAS-P)

Table 8: Optical Interface Support for Channelized OC3 IQ PICs

PIC Type Intermediate Reach (IR)

Optical interface Single-mode

Standard Telcordia GR-253

Maximum distance 9.3 miles/15 km

Transmit Wavelength 1274 through 1356 nm

Average launch power –15 through –8 dBm

Receiver saturation –8 dBm

Receiver sensitivity –28 dBm

PIC Type	Intermediate Reach (IR)
Optical interface	Single-mode
Standard	Telcordia GR-253
Maximum distance	9.3 miles/15 km
Transmit Wavelength	1274 through 1356 nm
Average launch power	–15 through –8 dBm
Receiver saturation	–8 dBm
Receiver sensitivity	–28 dBm

[ Contents] [ Prev] [ Next] [ Report an Error]

Description	One OC3 port Power requirement: 0.39 A @ 48 V (18.6 W) Fine-grained queuing per logical interface Channelization: DS3, DS1, DS0
Hardware features	Subrate and scrambling: Digital Link/Quick Eagle Kentrox Larscom ADTRAN Verilink Packet buffering, Layer 2 parsing M13/C-bit parity encoding DS3 far-end alarm and control (FEAC) channel support Local and remote loopback testing
Software features	Quality of service (QoS) per channel: weighted round-robin (WRR), random early detection (RED), weighted random early detection (WRED) Simple Network Management Protocol (SNMP): OC3 MIB, DS3 MIB, T1 MIB Dynamic, arbitrary channel configuration Full bit error rate test (BERT) Encapsulations: Circuit cross-connect (CCC) Translational cross-connect (TCC) Frame Relay High-Level Data Link Control (HDLC) Point-to-Point Protocol (PPP)
Cables and connectors	Duplex SC/PC connector (Rx and Tx); single-mode fiber intermediate-reach fiber
LEDs	One tricolor per port: Off—Not enabled Green—Online with no alarms or failures Amber—Online with alarms for remote failures Red—Active with a local alarm; router has detected a failure
Alarms, errors, and events	Alarms: Alarm indication signal—line (AIS-L) Alarm indication signal—path (AIS-P) Bit error rate signal degrade (BERR-SD) Bit error rate signal fail (BERR-SF) Idle code, idle received Loss of frame (LOF) Loss of pointer (LOP-P) Loss of signal (LOS) Out of frame (OOF) Payload mismatch (PLM-P) Payload unequipped (unequipped STS at path level) (UNEQ-P) Parity bit (P-bit) disagreements Path parity error Remote defect indication—line (RDI-L) Remote defect indication—path (RDI-P) Yellow alarm bit (X-bit) disagreements Error detection: Bit interleaved parity errors B1, B2, B3 (CV-S, CV-L, CV-P) Errored seconds (ES-S, ES-L, ES-P) Far-end bit errors, remote error indication—line (REI-L), far-end line coding violations (CV-LFE) Far-end bit errors, remote error indication—path (REI-P), far-end path coding violations (CV-PFE) Far-end block error (FEBE) Far-end errored seconds (ES-LFE, ES-PFE) Far-end severely errored seconds (SES-LFE, SES-PFE) Far-end unavailable seconds (UAS-LFE, UAS-PFE) Frame error Severely errored framing (SEF) Severely errored framing seconds (SEFS-S) Severely errored seconds (SES-S, SES-L, SES-P) Unavailable seconds (UAS-L, UAS-P)