Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation  Back up to About Overview 

10GE PR IOA

IOA labelES2-S2 10GE PR IOA
Number of IOA ports
  • 2
  • 1 active, 1 redundant
Software release
  • First supported: 7.2.0
Description
  • 48 W maximum
  • Full-height module
  • Uses a range of 10-gigabit small form-factor pluggable (XFP) transceivers to support different modes and cable lengths.
  • Pairs only with ES2 10G UPLINK LM, ES2 10G LM, and ES2 10G ADV LM to provide 10-Gigabit Ethernet operation through a single line interface
  • In a 100 Gbps configuration, the E320 router can accommodate up to two ES2 10G UPLINK LM and ES2-S2 10GE PR IOA combinations. You must install a combination in either of the turbo slots (slot 2 or slot 4).
  • In a 100 Gbps configuration, the E320 router can accommodate up to two ES2 10G LM and ES2-S2 10GE PR IOA combinations
  • In a 120 Gbps configuration, the E120 router can accommodate up to six ES2 10G UPLINK LM and ES2-S2 10GE PR IOA combinations. You can install a combination in any of the line module slots.
  • In a 320 Gbps configuration, the E320 router can accommodate up to twelve ES2 10G UPLINK LM and ES2-S2 10GE PR IOA combinations. You can install a combination in any of the line module slots.
  • In a 320 Gbps configuration, the E320 router can accommodate up to twelve ES2 10G LM and ES2-S2 10GE PR IOA combinations
Capability
  • Ethernet (IEEE 802.3ae)
  • 10Gb Base-SR/LR/ER/ZR
  • Port can operate in full duplex mode with an average data rate of 10 Gbps
Software features
  • See Ethernet IOAs for information about the layer 2 and layer 3 protocols and applications that this module combination supports.
Model compatibility
  • E320 router
  • E120 router
Line module compatibility
  • ES2 10G UPLINK LM
  • ES2 10G LM
  • ES2 10G ADV LM
SRP module compatibility
  • SRP-100
  • SRP-120
  • SRP-320
Line module redundancy compatibility
  • Not applicable
Port redundancy support
  • Yes
Cables and connectors (multimode [SR])
  • One LC full duplex connector
  • Transmit power:
    • min: –7.3 dBm
    • max: –1.0 dBm
  • Receive input power:
    • min: –9.9 dBm
    • max: –1.0 dBm
  • See the following corresponding table (SR Fiber Optic Cabling) for cabling requirements.
  • See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
Cables and connectors (single-mode [LR])
  • One LC full duplex connector
  • Transmit power:
    • min: –8.2 dBm
    • max: 0.5 dBm
  • Receive input power:
    • min: –14.4 dBm
    • max: 0.5 dBm
  • See the following corresponding table (LR Fiber Optic Cabling) for cabling requirements.
  • See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
Cables and connectors (single-mode [ER])
  • One LC full duplex connector
  • Transmit power:
    • min: –4.7 dBm
    • max: 4.0 dBm
  • Receive input power:
    • min: –15.8 dBm
    • max: –1.0 dBm
  • See the following corresponding table (ER Fiber Optic Cabling) for cabling requirements.
  • See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
Cables and connectors (single-mode [ZR])
  • One LC full duplex connector
  • Transmit power:
    • min: 0 dBm
    • max: 4 dBm
  • Receive input power:
    • min: –24.0 dBm
    • max: –7.0 dBm
  • See the following corresponding table (ZR Fiber Optic Cabling) for cabling requirements.
  • See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
LEDsBoard-level LEDs:
  • OK (green)—IOA online and is functioning properly
  • FAIL (red)—Failure detected

Port LEDs:
  • LK (green)—Ethernet link is up
  • ACT (green)—Blinks when Ethernet traffic is being received

Port labels:
  • W—Working port
  • P—Protect port (LK blinks when active cable is attached even though it is not the active working port)
Alarms, errors, and events
  • See Monitoring Ethernet Interfaces in JunosE Physical Layer Configuration Guide, Chapter 5, Configuring Ethernet Interfaces.

Table 17: SR Fiber Optic Cabling

Fiber TypeMinimal Modal Bandwidth at 850 nm (MHz*km)Maximum Operating Range (meters)
62.5 microns16026 (85.3 ft)
 20033 (108.27 ft)
50 microns40066 (216.54 ft)
 50082 (269.03 ft)
 2000300 (984.25 ft)

Table 18: LR Fiber Optic Cabling

Fiber TypeNominal Wavelength (nm)Maximum Operating Range (kilometers)
9 microns131010 (6.2 miles)

Table 19: ER Fiber Optic Cabling

Fiber TypeNominal Wavelength (nm)Maximum Operating Range (kilometers)
9 microns155040 (24.85 miles)

Table 20: ZR Fiber Optic Cabling

Fiber TypeNominal Wavelength (nm)Maximum Operating Range (kilometers)
9 microns155080 (49.6 miles)

Modified: 2015-07-23