Navigation
Back up to About Overview
[+] Expand All
[-] Collapse All
Symbols
A
- abnormal LED activity 1, 2
- access, management 1, 2
- setting up console 1, 2
- SNMP 1, 2
- Telnet setup
- accessing, fan tray
- adapters, I/O 1, 2
- agency certification 1, 2, 3, 4
- air filter 1
- airflow 1
- rack-mounted installation and
- specifications 1, 2
- alarm ports
- amperage 1, 2
- antistatic bags and containers
- assembly numbers, locating
- assigning an IP address
- auxiliary port 1, 2
B
- bays, upper and lower, right and left 1, 2, 3
- BNC connector
- booting
C
- cable management bracket
- cables
- cabling
- cabling router
- cabling SRP IOA
- Case Manager
- certification 1, 2, 3, 4
- chassis
- circulation, air
- classification, packet
- cleaning the router
- CLI (command-line interface)
- clock source input ports
- clocking problems
- command-line interface
- compliance
- components
- configuring cables 1, 2
- configuring management access
- configuring Telnet
- connecting console to the router
- connectors, pinouts
- console
- console port 1, 2
- consumption, power 1, 2
- conventions
- cooling system
- crossover cable
- current (electrical) requirements 1, 2
- customer support 1, 2
D
- damaged components, returning
- DB-9 connector 1, 2
- DC power 1, 2, 3
- detecting double-bit error
- diagnosing problems
- diagnostic LEDs
- dimensions of E120 router
- dimensions of E320 router
- dissipation, heat 1, 2
- distribution rack 1, 2
- documentation set
- double-bit errors
E
- E120 router
- assigning IP address to
- cabling
- cabling recommendations
- cleaning
- dimensions
- electrical requirements
- environmental requirements
- equipment rack requirements
- Ethernet cable
- installing
- installing modules
- lifting
- management access
- mechanical requirements
- modules
- power requirements
- powering down
- powering up
- safety guidelines
- site planning
- slot numbering
- space requirements 1, 2
- troubleshooting 1, 2
- unpacking
- views
- E320 router
- assigning IP address to
- cabling
- cabling recommendations
- cleaning
- dimensions
- electrical requirements
- environmental requirements
- equipment rack requirements
- Ethernet cable
- installing
- installing modules
- lifting
- management access
- mechanical requirements
- modules
- power requirements
- powering down
- powering up
- safety guidelines
- site planning
- slot numbering
- space requirements 1, 2
- troubleshooting 1, 2
- unpacking
- views
- EIA distribution rack
- ejectors, module
- electrical requirements 1, 2
- electronic equipment, recycling
- electrostatic discharge, precautions
- environmental requirements
- ESD grounding jack
- Ethernet link
- external timing ports
F
G
H
- halt command 1, 2
- hardware
- cable configuration 1, 2
- reclamation and recycling
- redundancy features
- repairing and replacing
- hazardous materials, reclamation and recycling
- heat dissipation 1, 2, 3
- high-availability mode
- hot-swapping fan trays
- hot-swapping modules
- humidity requirements 1, 2
- HyperTerminal
I
- I/O adapter 1, 2
- installing IOA shelf
- installing modules
- installing NVS cards 1
- installing router 1
- installing SFPs
- IOA module 1, 2
- IOA shelf 1
- IP address, assigning
J
L
M
- maintenance, system
- management
- management access 1, 2
- setting up console 1, 2
- SNMP 1, 2
- Telnet setup
- Management Information Bases
- management port
- managing modules
- manuals
- mechanical requirements for distribution rack
- MIBs (Management Information Bases)
- module reset button
- modules 1
- monitoring LEDs
- monitoring temperature
- mounting kits
- mounting posts for rack
N
- network management 1, 2
- setting up console 1, 2
- SNMP 1, 2
- Telnet setup
- network timing ports
- NMI button
- nonvolatile storage
- notice icons
- NVS cards 1
- installing 1, 2
- redundancy
- storing
O
P
- packaging, recycling
- packet classification
- packing instructions
- passwords, Telnet
- PC-CARD
- PCMCIA slot, SRP modules
- PDU 1
- pinouts, E Series router cables and connectors
- planning site for installation
- plenum
- ports
- power
- power distribution unit
- Power Distribution Unit (PDU)
- power input module, cabling
- power switches 1, 2
- powering down router
- powering up router
- preinstallation responsibilities
- preparing site for installation
- Privileged Exec command mode
- problems
- product numbers, locating
Q
R
- rack, distribution
- reclamation and recycling
- recycling Juniper Networks equipment
- redundancy 1
- regulatory requirements
- release mechanisms for SFPs
- removing components
- removing modules
- removing SFPs
- repacking components
- repairing hardware components
- replacing components
- replacing modules
- replacing NVS cards 1, 2, 3
- replacing SFPs 1, 2
- reset button
- resetting modules
- Restriction of Hazardous Substances (RoHS) Directive, recycling equipment
- Return Materials Authorization
- returning product
- RJ-45 connector 1, 2
- RMA (Return Materials Authorization)
- RoHS (Restriction of Hazardous Substances) Directive, recycling equipment
- RS-232 port 1, 2, 3, 4, 5
S
- safety
- agency certification 1, 2
- guidelines
- self-testing, modules
- serial numbers, locating
- SFM (switch fabric module) 1, 2
- SFPs (small form-factor pluggable transceivers) 1, 2
- show interface command
- show version command 1, 2, 3, 4, 5, 6, 7
- single-bit errors
- site planning
- size
- slices, fabric
- slot combinations 1, 2
- slot disable command
- slot groups 1
- slot numbering 1, 2
- small form-factor pluggable transceivers
- SNMP for management access 1, 2
- space requirements 1, 2, 3, 4
- specifications
- SRP (switch route processor) module 1, 2
- errors on
- installing
- IOA
- PCMCIA slot
- powering down
- redundancy
- removing 1, 2
- switch fabric slice 1, 2
- SRP IOA 1
- cabling 1, 2
- installing
- removing
- starting router
- static electricity, protecting against
- storing, modules and components
- support, technical See technical support
- switch fabric modules
- switch fabric slices 1, 2
- switch router processor modules
- switches, power 1, 2
- switchover, SRP modules
- synchronization, SRP modules
- system maintenance
T
- technical support 1
- Telnet connection to router
- temperature
- excessive 1, 2
- monitoring
- requirements 1, 2
- text and syntax conventions
- thermal protection mode 1, 2, 3
- timing port
- tools required
- cabling router
- installing modules
- removing components 1, 2
- unpacking router
- troubleshooting 1, 2
- booting
- cables 1, 2
- clocking
- double-bit errors
- Ethernet link
- fans 1, 2
- LED activity for
- modules 1, 2
- power failure 1, 2
- safety guidelines
U
V
W
- Waste Electrical and Electronic Equipment (WEEE) Directive. See WEEE Directive
- WEEE (Waste Electrical and Electronic Equipment) Directive, recycling equipment
- weight
- of E120 router
- of E320 router
- of rack 1, 2
Download This Guide
Installing an SRP Module or SFM Module
You must install SRP modules in slot 6 or slot 7, and SFM modules in slots 8, 9, or 10. Four of the five fabric slots (SRP and SFM modules) must have a module installed for the router to function. A minimum system configuration requires all three SFMs and at least one SRP module to be installed. See Fabric Slices for more information.
To install an SRP module or SFM module:
- Ground yourself by using an antistatic wrist strap or other device and connect it to one of the ESD grounding jacks on the chassis.
- Choose the slot in which you want to install the module.
- SRP module – slot 6 or 7
- SFM module – slot 8, 9, or 10
See Figure 12 and Figure 14 for module locations.
Note: Four of the five fabric slots (SRP and SFM modules) must have a module installed for the router to function. A minimum system configuration requires all three SFMs and at least one SRP module to be installed.
- With a No. 2 Phillips screwdriver, loosen the captive screws that secure the blank filler panel covering the empty chassis slot, if present, and remove the filler panel.
- Remove the module from its antistatic bag, being careful not to touch module components, pins, leads, or solder connections.
- Verify that the ejectors are in the open position, as
shown in Figure 19.
Figure 19: Closing Ejectors from the Open Position
- Slide the module into the chassis by placing it between
the guides of the selected slot and pushing the module until it stops.
The module stops sliding when the ejectors make contact with the front of the chassis.
Caution: If you meet strong resistance when attempting to seat the module using the ejectors, remove it from the chassis and confirm that the slot is designed to hold the module. Also, be sure that you have aligned the top and bottom edges in the correct matching tracks.
- Insert the module into the backplane by simultaneously depressing both ejectors (as shown in Figure 19), exerting forward pressure on the module.
- Tighten the module's captive screws using the No. 2 Phillips
screwdriver.
Note: Tighten the captive screws completely before installing an adjacent module so that proper EMI gasket compression occurs. Failure to do this can make it difficult to install adjacent modules.
Caution: Do not overtighten the screws.
