Fields for Exceptions to Stateless Firewalls in Enterprise Manager Portal

Rule Name

• Name of the subscription to the firewall service.

• Value—Alphanumeric string

• Guidelines—You must specify a name for the rule. Do not use spaces, dots, or punctuation characters in the name.

• Default—No value

• Example—WebAccess

IP Protocols

• IP protocol associated with this rule.

• Value—Type of IP protocols separated by commas, with the protocol specified by:
  • Number of IP protocol in the range 0–255
  • The following abbreviations:
  • ah—authentication header
  • egp—exterior gateway protocol
  • esp—Encapsulating Security Payload
  • gre—generic routing encapsulation
  • icmp—Internet Control Message Protocol
  • igmp—Internet Group Management Protocol
  • ipip—IP over IP
  • ospf—Open Shortest Path First
  • pim—Protocol Independent Multicast
  • rsvp—Resource Reservation Protocol
  • sctp—Stream Control Transmission Protocol
  • tcp—Transmission Control Protocol
  • udp—User Datagram Protocol
  • Blank—Any IP protocol

• Default—No value

• Example—tcp

ToS Byte

• ToS byte in the header of the IP datagram associated with traffic affected by this rule.

• Value
  • DiffServ—DiffServ is used to classify packets by the selected value.
  • Precedence—Value for the drop precedence.
  • Free Format—ToS byte in binary format.

Use an x to indicate a bit to be ignored.

• Guidelines—You can configure the ToS byte only if the configuration level is set to Advanced.

  Specify the ToS byte in this field if you want to specify a specific type of service. If you want to specify all types of service, leave this field empty.

• Default—No value

• Example—Free Format 000010xx

Source IP Addresses

• IP addresses (as contained in the IP packets) of traffic to which the rule applies.

• Value—[ not ]<networkAddress>/<networkMask>
  • not—All addresses except the listed addresses
  • <networkAddress>—IP address of the network
  • <networkMask>—Subnet mask

• Guidelines—To specify traffic with a particular source IP address, enter an IP address. To specify all traffic except that with a particular source IP address, precede the IP address with the keyword not. To specify traffic with any source IP address, leave the field empty. To specify multiple source IP addresses, enter multiple addresses on different lines. You can specify multiple source IP addresses only if the configuration level is set to Advanced.

• Default—No value

• Example—192.0.2.0/24

Source Ports

• Source TCP/UDP port(s) (contained in the IP packets) of traffic affected by this rule.

• Values
  • Port number
  • Comma-separated list of port numbers and ranges of port numbers (devices running Junos OS)
  • Ranges of port numbers separated by two dots (..)

• Guidelines— To specify all ports, leave this field empty. If you specify an IP protocol other than TCP or UDP for this subscription, the port field will dim, and you will not be able to specify port numbers in this field.

• Default—No value

• Example
  • 2
  • 2, 3, 45..55

Destination IP Addresses

• Destination IP addresse(es) (contained in the IP packets) of traffic affected by this rule.

• Value—[ not ]<networkAddress>/<networkMask>
  • not—Address, or set of IP addresses as expressed by the netmask, for which the firewall service is not available
  • <networkAddress>—IP address of the network
  • <networkMask>—Netmask expressed as an integer 0–32, which specifies how many of the first bits in the address specify the network

• Guidelines—To specify a netmask for a destination IP address or a set of IP addresses that should not be included, precede the IP address with the keyword not. The order in which you list prefixes, identified by the IP address–netmask pair, is not significant. They are all evaluated to determine whether a match occurs. If prefixes overlap, longest-match rules are used to determine whether a match occurs. For an address to be considered a match, it must match one of the rules in the list.

  For information about how devices running Junos OS evaluate prefixes, see the Junos OS Policy Framework Configuration Guide.

• Default—No value

• Example—192.0.2.0/24

Destination Ports

• Destination TCP/UDP port(s) (contained in the IP packets) of traffic affected by this rule.

• Value
  • Port number
  • Comma-separated list of port numbers and ranges of port numbers (devices running Junos OS)
  • Ranges of port numbers separated by two dots (..)

• Guidelines—To specify all ports, leave this field empty. If you specify an IP protocol other than TCP or UDP for this subscription, the port field will dim, and you will not be able to specify port numbers in this field.

• Default—No value

• Example
  • 2
  • 2, 3, 45..55

TCP Flags

• Conditions in the TCP flags in the TCP message header. This field is enabled when the TCP protocol is selected.

• Value—Expression or text synonym that identifies the TCP flags

• Guidelines—You can enter a value for TCP flags only if you select TCP as the IP protocol.

  You can enter a logical expression that contains the symbols for the six TCP flags: urgent, ack, push, rst, syn, and fin. You can use the following logical operators in the list of flags:

  • &—And. Separates flag settings in the list.
  • !—Not. Flags preceded by ! are cleared; flags not preceded by ! are set.

  You can use the following expression instead of the entire expression:

  • tcp-initial—syn & !ack

  The interface displays text synonyms for expressions if stored data matches the expression.

  This field appears enabled only if the configuration level is set to Advanced. Although the value can be changed when the configuration level is set to Normal, we recommend that the value of this field not be changed if the field appears disabled.

• Default—No value

• Example
  • syn
  • tcp-initial

Fragmentation Flags

• Logical expression using the dont-fragment, more-fragments, and reserved IP fragmentation flags.

• Value—Flags expression

• Guidelines—The expression can also contain the following logical operators:
  • &—And. Separates flag settings in the list.
  • !—Not. Flags preceded by ! are cleared; flags not preceded by ! are set.

• Default—No value

• Example
  • more-fragments
  • ! dont-fragment

Fragment Offset

• IP fragment offset—a value that defines the order in which to assemble fragments for an IP datagram.

• Value—One of the following:
  • Number in the range 0–8191
  • Range of numbers separated by two dots (..) within the range 0–8191

• Default—No value

• Example
  • 50
  • 50 .. 76

Packet Length

• Length of packets.

• Value—One of the following:
  • Number in the range 0–65536
  • Range of numbers separated by two dots (..) within the range 0–65536

• Default—No value

• Example
  • 15000
  • 15000 .. 30000

ICMP Type

• Type of message for Internet Control Management Protocol (ICMP).

• Value—Type of ICMP message in the following formats:
  • Number of the ICMP message type in the range 0–255
  • Symbolic name for an ICMP message type
  • Comma-separated list of ICMP types and ranges of ICMP types
  • Ranges of ICMP types separated by two dots (..) within the range 0–255
  • Blank—Any ICMP type

• Guidelines—You can enter a value for this field only if you select the icmp protocol (protocol number 1).

The following list shows the symbolic name and associated numbers for ICMP types. The ICMP types are the same as those on devices running Junos OS with the addition of traceroute.

• 0—echo-reply
• 8—echo-request
• 16—info-reply
• 15—info-request
• 18—mask-reply
• 17—mask-request
• 12—parameter-problem
• 5—redirect
• 9—router-advertisement
• 10—router-solicit
• 4—source-quench
• 11—time-exceeded
• 13—timestamp
• 14—timestamp-reply
• 30—traceroute
• 3—unreachable

  This field appears enabled only if the configuration level is set to Advanced. Although the value can be changed when the configuration level is set to Normal, we recommend that the value of this field not be changed if the field appears disabled.

• Default—Any

• Example—10 .. 25, 27

ICMP Code

• Code for ICMP.

• Value—Type of ICMP code in the following formats:
  • Number of ICMP code in the range 0–255
  • Comma-separated list of code numbers and ranges of code numbers
  • Ranges of code numbers separated by two dots (..) within the range 0–255
  • Blank—Any ICMP code

• Guidelines—You can enter a value for this field only if you select particular protocols.

  This field appears enabled only if the configuration level is set to Advanced. Although the value can be changed when the configuration level is set to Normal, we recommend that the value of this field not be changed if the field appears disabled.

• Default—Any

• Example—75

Priority

• Numeric value that indicates which firewall exception takes precedence if a subscriber has multiple exceptions for a firewall service.

• Value—Integer in the range specified by the online help for this field

• Guidelines—You must specify a priority for the firewall exception. A lower number indicates a higher priority. Use a unique priority for each firewall exception that relates to the same traffic. If two rules have the same priority, they will be applied to traffic in an unpredictable order.

• Default—No value

• Example—5

Direction

• Direction, with respect to the enterprise, of the traffic.

• Value
  • Incoming—Applies to traffic that starts outside the enterprise
  • Outgoing—Applies to traffic that starts inside the enterprise
  • Both—Applies to traffic flows that start inside or outside the enterprise
  • Guidelines—If you select a custom firewall rule, you cannot specify a direction. Custom firewall rules should have names that reflect what the rule does.

• Default—Incoming

• Example—Both

Action

• Way in which the firewall should handle the incoming or outgoing traffic.

• Value
  • Allow—Let the traffic through the firewall.
  • Reject—Send an ICMP reply that explains why the firewall blocked the traffic.
  • Discard—Drop the traffic without sending any reply.
  • A custom value configured by the service provider.

• Guidelines—Other actions may be available—one for each custom firewall rule.

• Default—Allow

• Example—Discard

Enabled

• Status of the rule.

• Value
  • Gray box—Rule is inherited from a parent subscriber or the rule is scheduled
  • White box—Rule is configured for this subscriber
  • Box with check mark—Rule is enabled
  • Empty box—Rule is disabled

• Guidelines—Click box to enable or disable a rule.

• Default—Rule is disabled