Elements that You Can Configure in the CLI

To list the elements that you can configure using the CLI, type enable at the prompt and press Enter. Table 35 list the configurable elements that appear.

Table 35: Configurable Elements in the CLI

Command	Description	Supported Users
config snr	Selects SNR units between AMU or dBHz. Note: This command is not available if the TCA6500 Timing Client uses the Resolution SMT GPS Timing Receiver. The AMU is not an industry standard unit of measurement.	Admin Read/Write
config gps anti-jamming	Enables or disables the anti-jamming capability for the Resolution SMT GPS Timing Receiver. Note: This command is available only if the TCA6500 Timing Client uses the Resolution SMT GPS Timing Receiver.	Admin Read/Write
config web-timeout	Configures the web-timeout. [min]	Admin Read/Write
config hostname	Configures the host name. {hostname}	Admin Read/Write
config domain	Configures the domain. {domain name}	Admin Read/Write
config alarm-email-receiver	Configures recipients of alarm email notifications	Admin Read/Write
config dns0	Configures the primary DNS server IP.	Admin Read/Write
config dns1	Configures the second DNS server IP.	Admin Read/Write
config password	Modifies your current login password.	Admin
config enable-password	Modifies the password of the enable mode.	Admin
config web	Configures the web enable/disable.	Admin Read/Write
config web-mode	Configures the web mode.	Admin Read/Write
config timezone	Configures the timezone information.	Admin Read/Write
config cli-timeout	Configures the session in-action session timeout.	Admin Read/Write
config alarm-profile	Configures the alarm profile.	Admin Read/Write
config snmp readwrite-community	Configures the SNMP read and write community.	Admin Read/Write
config snmp readonly-community	Configures the SNMP read only community.	Admin Read/Write
config snmp contact	Configures the SNMP contact.	Admin Read/Write
config ptp add server	Adds a ptp server.	Admin Read/Write
config snmp-v3user add	Adds a SNMP v3 user.	Admin Read/Write
config snmp-v3user del	Deletes a SNMP v3 user.	Admin Read/Write
config snmp-trap add	Adds a trap receiver address to the list.	Admin Read/Write
config snmp-trap del	Deletes a trap receiver from the list.	Admin Read/Write
config language	Configures the web pages language.	Admin Read/Write
config antenna-voltage	Configures the input voltage for the antenna between 3.3 or 5V.	Admin Read/Write
config sync-src-priority	Configures the highest priority Sync Source that the Timing Client should use. Choices include: GPS, E1, PTP, or Internal.	Admin Read/Write
config eth0 ip-mode	Selects the IP mode for the Ethernet 0 (LAN1) port between Static and DHCP.	Admin Read/Write
config eth0 ip	Configures IP settings for Ethernet 0 (LAN1) port : IP address, mask, and gateway.	Admin Read/Write
config eth0 speed	Selects the speed for the Ethernet 0 (LAN1) port between 10 and 100Mbps.	Admin Read/Write
config eth0 duplex	Selects the duplex mode for the Ethernet 0 (LAN1) port between half or full duplex.	Admin Read/Write
config eth0 auto-nego	Turns Auto Negotiation ON or OFF for Ethernet 0 (LAN1) port.	Admin Read/Write
config e1 output port	Configures the E1 output port’s number of ports, mode, framing, encoding, LBO, SSM, and state	Admin Read/Write
config ppx	Configures ppx.	Admin Read/Write
config e1 output loopback	Configures the E1 input port’s number of ports, mode, framing, encoding, Receive Sensitivity, SSM, and state	Admin Read/Write
config 1/5/10MHz	Selects between 1MHz, 5MHz, and 10MHz output on the 1/5/10MHz port.	Admin Read/Write
config ptp slave	Configures PTP slave.	Admin Read/Write
config ptp slv enable	Enables the PTP protocol.	Admin Read/Write
config ptp slv disable	Disables the PTP protocol.	Admin Read/Write
config ptp slv dscp	Configures the Differential Service (DiffServ) of the IP packet.	Admin Read/Write
config ptp slv domain	Configures the PTP domain number to be part of the same Grandmasters domain.	Admin Read/Write
config ptp slv profile	Configures the profile for unicast packet types for both sync and delay request / response PTP event messages.	Admin Read/Write
config ptp unicast sync	Configures the sync message rate that the Timing Client requests from the Grandmaster.	Admin Read/Write
config ptp unicast delay	Configures the delay response message rate that the Timing Client requests from the Grandmaster.	Admin Read/Write
config ptp unicast announce	Configures the announce message rate that the Timing Client requests from the Grandmaster.	Admin Read/Write
config ptp unicast duration	Configures the Timing Client expiration duration for sending signaling messages without receiving an acknowledgement from the Grandmaster.	Admin Read/Write
config ptp unicast acc-master add	Adds the IP address of the acceptable Grandmasters for the Timing Client, which is used for the Ethernet network packet IP protocol.	Admin Read/Write
config ptp unicast acc-master del	Deletes the IP address of the acceptable Grandmasters for the Timing Client, which is used for the Ethernet network packet IP protocol.	Admin Read/Write
config ptp unicast signaling	Enables or disables the sending of the signaling messages to the Grandmaster. enable—Enables the sending of the signaling messages to the Grandmaster. disable—Disables the sending of the signaling messages to the Grandmaster.	Admin Read/Write
config datetime	Configures date and time for the Timing Client.	Admin Read/Write
config primary-ptp-server	Configures the primary (ptp) proprietary packet based timing protocol	Admin Read/Write
config secondary-ptp-server	Configures the secondary (ptp) proprietary packet based timing protocol	Admin Read/Write
config holdover-state	Configures the TCA system to remain in the holdover state or change to the internal state after 24 hours of holdover state. 1—The system remains in the holdover state instead of changing to the internal state after 24 hours of holdover state. However, the system changes to the internal state when the signal is lost during acquisition, locking, or resetting the system. 0 (default)—The system changes to the internal state after 24 hours of holdover state.	Admin Read/Write
config pps-squelch	Turns on or off the PPS squelch. On—The PPS squelch is turned on, thereby disabling the PPS output when the TCA system is not locked to GPS or PTP. Off (default)—The PPS squelch is turned off, thereby enabling the PPS output even when the TCA system is not locked to GPS or PTP.	Admin Read/Write
config radius-server add	Adds the IP address of the RADIUS authentication server and sets other related configurations (secret word, retries, timeout, and port) to be used by the Timing Client for user authentication.	Admin Read/Write
config radius-server del	Deletes the RADIUS authentication server and its configuration from the authentication server list by using the IP address of the authentication server.	Admin Read/Write
config auth-order	Configures the authentication order to be followed by the Timing Client while authenticating an user. The following combination of authentication order is allowed: RADIUS server authentication and then local authentication Local authentication and then RADIUS server authentication Only RADIUS server authentication Only local authentication	Admin Read/Write
config accounting-server add	Adds the IP address of the RADIUS accounting server and sets other related configurations (secret word, retries, timeout, and port) to be used by the Timing Client for accounting.	Admin Read/Write
config accounting-server del	Deletes the RADIUS accounting server and its configuration from the accounting server list by using the IP address of the accounting server.	Admin Read/Write
config accounting-level	Configures the information to be used by the Timing Client for accounting. The values are: 1—For login accounting only 2—For interactive and login accounting 3—For configuration, interactive and login accounting	Admin Read/Write
config accounting	Enables or disables RADIUS accounting in the Timing Client.	Admin Read/Write
config user add	Creates a new user account with login class as Read-Only or Read/Write.	Admin
config user del	Deletes the Read-Only or Read/Write user account.	Admin
config user password	Creates a new password for the Read-Only or Read/Write user account.	Admin
config user class	Modifies the login class for the Read-Only or Read/Write user account.	Admin
config change-password	Modifies your current login password.	Read/Write
reset password	Restores the default password value.	Admin
reset config	Restores the TCA6500 Timing Client to the manufacturer default configuration.	Admin
reboot	Reboots the system.	Admin Read/Write
restart timeprobe-agent	Starts or enables the time probe agent	Admin Read/Write
halt	Halts the system.	Admin Read/Write
ping	Pings the remote host.	Admin Read/Write
tftp	Installs a software upgrade image file by TFTP	Admin Read/Write
save daemonlog	Saves the daemon log to a TFTP server.	Admin Read/Write
save syslog	Saves the system log to a TFTP server.	Admin Read/Write
save authlog	Saves the author log to a TFTP server.	Admin Read/Write
save eventlog	Saves the event log to a TFTP server.	Admin Read/Write
backup	Backs up the configuration file to a TFTP server.	Admin Read/Write
restore	Restores the configuration file to a TFTP server.	Admin Read/Write
clear alarm	Clears the alarm.	Admin Read/Write
tftp license	Upload TFTP license for value-added features.	Admin Read/Write
clear daemon log	Clears daemon log.	Admin Read/Write
clear syslog	Clears system log.	Admin Read/Write
clear eventlog	Clears event log.	Admin Read/Write
clear authlog	Clears authorization log.	Admin Read/Write