Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

SRX4200 Transceiver Specifications and Pinouts

 

Pluggable Transceivers Supported on SRX4200 Services Gateways

The ports on the SRX4200 Services Gateway supports SFP+ transceivers. The following are the transceivers supported on the services gateway:

  • EX-SFP-1GE-T

  • EX-SFP-10GE-ER

  • SRX-SFP-10GE-ER

  • SRX-SFP-10GE-LR

  • SRX-SFP-10GE-SR

  • JNP-10G-SR-8PACK

  • SRX-SFP-1GE-LH

  • SRX-SFP-1GE-LX

  • SRX-SFP-1GE-SX

  • JNP-1G-SX-8PACK

  • SRX-SFP-1GE-T

    Note

    The SRX4200 Services Gateway supports only 1000-Mbps speed on SRX-SFP-1GE-T and EX-SFP-1GE-T; 10-Mbps and 100-Mbps speeds are not supported.

  • JNP-1G-T-8PACK

For the full specifications of these transceivers, see The Hardware Compatibility Tool.

Note

When using 1-gigabit transceivers, the name of the interface follows the convention xe-0/0/port-number but the interface operates at 1-Gbps speed.

SFP+ Direct Attach Copper Cables for SRX4200 Services Gateways

Small form-factor pluggable plus transceiver (SFP+) direct attach copper (DAC) cables are suitable for short distances of up to 23 ft (7 m), making them ideal for highly cost-effective networking connectivity within a rack and between adjacent racks. The SRX4200 Services Gateway supports the following 1 m and 3 m long DAC cables:

  • SRX-SFP-10GE-DAC-1M

  • SRX-SFP-10GE-DAC-3M

For the full specifications of these transceivers, see The Hardware Compatibility Tool.

Management Port Connector Pinout Information for an SRX4200 Services Gateway

The port on the front panel labeled MGMT is an autosensing 10/100/1000-Mbps Ethernet RJ-45 receptacle that accepts an Ethernet cable for connecting the services gateway to a management LAN (or other device that supports out-of-band management). Two LEDs on the port indicate link activity on the port and the administrative status of the port.

Table 1 provides the pinout information for the RJ-45 connector for the management port. An RJ-45 cable, with a connector attached, is supplied with the services gateway.

Table 1: Management Port Connector Pinout Information

Pin

Signal

1

TX+

2

TX-

3

RX+

4

Termination network

5

Termination network

6

RX-

7

Termination network

8

Termination network

Console Port Connector Pinout Information for an SRX4200 Services Gateway

The console port is an RS-232 serial interface that uses an RJ-45 connector to connect to a console management device. The default baud rate for the console port is 9600 baud.

Table 2 provides the pinout information for the RJ-45 console connector. An Ethernet cable that has an RJ-45 connector at either end and an RJ-45 to DB-9 serial port adapter are supplied with the services gateway.

Table 2: Console Port Connector Pinout Information

Pin

Signal

Description

1

RTS

Request to Send

2

DTR

Data Terminal Ready

3

TXD

Transmit Data

4

Ground

Signal Ground

5

Ground

Signal Ground

6

RXD

Receive Data

7

DSR/DCD

Data Set Ready

8

CTS

Clear to Send