Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Connecting the SRX320 to Power

 

Required Tools and Parts for Grounding the SRX320 Services Gateway

To ground and to provide power to the services gateway, you need the following tools:

  • Phillips (+) screwdrivers, numbers 1 and 2

  • Electrostatic discharge (ESD) grounding wrist strap

  • Wire cutters

Connecting the SRX320 Services Gateway Grounding Cable

You ground the services gateway by connecting a grounding cable to earth ground and then attaching it to the chassis grounding point located on the back panel of the device using one M4 grounding screw.

You must provide the following items:

  • M4 grounding screw

  • Grounding cables

  • Cable lugs (for example, Panduit LCC6-10A-L)

Caution

Before you connect power to the services gateway, a licensed electrician must attach a cable lug to the grounding and power cables that you supply. A cable with an incorrectly attached lug can damage the services gateway (for example, by causing a short circuit).

To ground the device:

  1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. For more details, see Prevention of Electrostatic Discharge Damage.
  2. Ensure that all grounding surfaces are clean and brought to a bright finish before grounding connections are made.
  3. Connect the grounding cable to a proper earth ground.
  4. Place the grounding cable lug over the grounding point (sized for M4 grounding screws) on the rear of the chassis.
  5. Secure the grounding cable lug to the grounding point, first with the washer, then with the screw.
  6. Dress the grounding cable and verify that it does not touch or block access to the services gateway components and that it does not drape where people could trip on it.
    Figure 1: Connecting the SRX320 Services Gateway Grounding Cable
    Connecting the SRX320 Services Gateway Grounding Cable

Note

The device should be permanently connected to ground during operation.

Connecting the SRX320 Services Gateway to the Power Supply

To connect the device to the power supply:

Caution

Before connecting the device to the power supply, attach an ESD strap to an ESD point and place the other end of the strap around your bare wrist.

  1. Plug the DC connector end of the power cable into the power connector on the back of the device as shown in Figure 2.
  2. Plug the AC adapter end of the power cable into an AC power outlet.
Figure 2: Connecting the SRX320 Services Gateway to the Power Supply
Connecting
the SRX320 Services Gateway to the Power Supply

Powering On the SRX320 Services Gateway

To power on the services gateway:

  1. Ensure that you have connected the power supply to the device.
  2. Insert the plug of the power supply adapter into an AC power source receptacle.
  3. Turn on the power to the AC power receptacle.

The device starts automatically as the power supply completes its startup sequence. The PWR LED lights during startup and remains on when the device is operating normally.

Note

After the power supply is turned on, it can take up to 60 seconds for status indicators—such as the STAT and PWR LEDs—to show that the power supply is functioning normally. Ignore error indicators that appear during the first 60 seconds.

Note

When the system is completely powered off and you turn on the power supply, the device starts as the power supply completes its startup sequence. If the device finishes starting and you need to power off the system again, first issue the CLI request system power-off command.

Powering Off the SRX320 Services Gateway

You can power off the services gateway in one of the following ways:

  • Graceful shutdown—Press and immediately release the Power button. The device begins gracefully shutting down the operating system and then powers itself off.

    Caution

    Use the graceful shutdown method to power off or reboot the services gateway.

  • Forced shutdown—Press the Power button and hold it for ten seconds. The device immediately powers itself off without shutting down the operating system.

    Caution

    Use the forced shutdown method as a last resort to recover the services gateway if the services gateway operating system is not responding to the graceful shutdown method.

Warning

Do not press the Power button while the device is shutting down.

Caution

Forced shutdown can result in data loss and corruption of the file system.

Note

To remove power completely from the device, unplug the power cord or switch off the AC power source.

After powering off a power supply, wait at least 10 seconds before turning it back on. After powering on a power supply, wait at least 10 seconds before turning it off.

The power button on the services gateway is a standby power switch, which will not turn off the input power to the services gateway.

Tip

When you are powering off the device, the CLI displays the following message: Turning the system power off. You can now safely remove the power cable to completely power off the device.

Note

You can use the request system reboot CLI command to schedule a reboot.