Connecting the SRX300 to Power
Required Tools and Parts for Grounding the SRX300 Services Gateway
To ground and to provide power to the services gateway, you need the following tools:
Phillips (+) screwdrivers, numbers 1 and 2
Electrostatic discharge (ESD) grounding wrist strap
Connecting the SRX300 Services Gateway Grounding Cable
You ground the services gateway by connecting a grounding cable to earth ground and then attaching it to the chassis grounding point located on the back panel of the device using a M4 screw.
You must provide the following items:
One M4 screw
Cable lugs (for example, Panduit LCC6-10A-L)
Before you connect power to the services gateway, a licensed electrician must attach a cable lug to the grounding and power cables that you supply. A cable with an incorrectly attached lug can damage the services gateway (for example, by causing a short circuit).
To ground the device:
- Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to the ESD point on the chassis. For more details, see Preventing Electrostatic Discharge Damage to the SRX300 Services Gateway.
- Ensure that all grounding surfaces are clean and brought to a bright finish before grounding connections are made.
- Connect the grounding cable to a proper earth ground.
- Place the grounding cable lug over the grounding point (sized for M4 screws) on the rear of the chassis as shown in Figure 1.
- Secure the grounding cable lug to the grounding point, first with the washer, then with the screw.
- Dress the grounding cable and verify that it does not touch or block access to the services gateway components and that it does not drape where people could trip on it.
The device should be permanently connected to ground during operation.
Connecting the SRX300 Services Gateway to the Power Supply
To connect the device to the power supply:
Before connecting the device to the power supply, attach an ESD strap to an ESD point and place the other end of the strap around your bare wrist.
- Plug the DC connector end of the power cable into the power connector on the back of the device as shown in Figure 2.
- Plug the AC adapter end of the power cable into an AC power outlet.
Powering On the SRX300 Services Gateway
To power on the services gateway:
- Ensure that you have connected the power supply to the device.
- Insert the plug of the power supply adapter into an AC power source receptacle.
- Turn on the power to the AC power receptacle.
The device starts automatically as the power supply completes its startup sequence. The PWR LED lights during startup and remains on when the device is operating normally.
After the power supply is turned on, it can take up to 60 seconds for status indicators—such as the STAT and PWR LEDs—to show that the power supply is functioning normally. Ignore error indicators that appear during the first 60 seconds.
When the system is completely powered off and you turn on the power supply, the device starts as the power supply completes its startup sequence. If the device finishes starting and you need to power off the system again, first issue the CLI request system power-off command.
Powering Off the SRX300 Services Gateway
You can power off the services gateway in one of the following ways:
Graceful shutdown—Press and immediately release the Power button. The device begins gracefully shutting down the operating system and then powers itself off.
Use the graceful shutdown method to power off or reboot the services gateway.
Forced shutdown—Press the Power button and hold it for ten seconds. The device immediately powers itself off without shutting down the operating system.
Use the forced shutdown method as a last resort to recover the services gateway if the services gateway operating system is not responding to the graceful shutdown method.
Do not press the Power button while the device is shutting down.
Forced shutdown can result in data loss and corruption of the file system.
To remove power completely from the device, unplug the power cord or switch off the AC power source.
After powering off a power supply, wait at least 10 seconds before turning it back on. After powering on a power supply, wait at least 10 seconds before turning it off.
The power button on the services gateway is a standby power switch, which will not turn off the input power to the services gateway.
When you are powering off the device, the CLI displays the following message: Turning the system power off. You can now safely remove the power cable to completely power off the device.
You can use the request system reboot CLI command to schedule a reboot.