ON THIS PAGE
Configuration Statements and Operational Commands
member (Redundant Power System)
Syntax
Hierarchy Level
Release Information
Statement introduced in Junos OS Release 12.1.
Description
Specify the Virtual Chassis member ID of a switch connected to the Redundant Power System (RPS) for backup power supply. The member ID is required only for switches that can be configured in a Virtual Chassis. If the switch has never been configured in a Virtual Chassis, the value is always 0.
Options
member-number—Member ID of a switch that has Virtual Chassis capability that is connected to the RPS.
Range: 0 through maximum members in the Virtual Chassis
Default: 0
The remaining statement is explained separately. See CLI Explorer.
Required Privilege Level
admin—To view this statement in the configuration.
admin-control—To add this statement to the configuration.
priority (Redundant Power System)
Syntax
Hierarchy Level
Release Information
Statement introduced in Junos OS Release 12.1.
Description
Configure the backup of any switch connected to the Redundant Power System (RPS) using the CLI on each switch. The determines the order in which the RPS supplies backup power to the switches connected to the RPS. 6 is the highest priority and 1 is lowest. Zero means off or no RPS backup.
If the switch is not reconfigured from the CLI, the default priority is 1. In this case, priority is determined by connector location with the rightmost connector having the highest priority.
For switches that can only be used as standalone switches, this hierarchy level is used for configuration:
For switches that can be used either as standalone switches or configured in a Virtual Chassis, this hierarchy level is used for configuration:
If two or more connections are assigned the same , then the power of each connection is determined based on its switch connector port location, with the rightmost port receiving power first.
Required Privilege Level
admin—To view this statement in the configuration.
admin-control—To add this statement to the configuration.
redundant-power-system
Syntax
EX2200 switch:
EX3300 switch:
Hierarchy Level
Release Information
Statement introduced in Junos OS Release 12.1.
Description
Configure Redundant Power System (RPS) member to ensure higher- switches always receive power backup.
The remaining statements are explained separately. See CLI Explorer.
Required Privilege Level
admin—To view this statement in the configuration.
admin-control—To add this statement to the configuration.
request redundant-power-system multi-backup
Syntax
EX2200 switch:
request redundant-power-system multi-backup request redundant-power-system no-multi-backup
EX3300 switch:
request redundant-power-system multi-backup member member-number request redundant-power-system no-multi-backup member member-number
Release Information
Command introduced in Junos OS Release 12.1.
Description
Configure a redundant power system (RPS) to back up six non-Power-over-Ethernet (PoE) powered switches instead of the default which is to back up three PoE-powered switches.
Required Privilege Level
admin—To view this statement in the configuration.
admin-control—To add this statement to the configuration.
List of Sample Output
request redundant-power-system multi-backupSample Output
request redundant-power-system multi-backup
user@switch> request redundant-power-system
multi-backup member 1 Sending multi-backup setting to RPS
show chassis redundant-power-system
Syntax
Release Information
Command introduced in Junos OS Release 12.1.
Description
Display information about the Redundant Power Systems (RPS) connected to the switch.
Required Privilege Level
view
List of Sample Output
show chassis redundant-power-system (Standalone Switch)show chassis redundant-power-system (Virtual Chassis member)
Output Fields
Table 1 lists the output fields for the show chassis redundant-power-system command. Output fields are listed in the approximate order in which they appear.
Table 1: show chassis redundant-power-system Output Fields
Field Name | Field Description | Level of Output |
|---|---|---|
Member | Member number of the switch connected to the RPS—For a switch that has never been configured in a Virtual Chassis, the value is always zero. For a Virtual Chassis member, the range is zero through the maximum number of members in the Virtual Chassis. | All levels |
Status | Status of the RPS:
| All levels |
RPS | Serial number of the RPS. | |
Port | Number of the switch connector on the RPS that is connected to a switch. | All levels |
Sample Output
show chassis redundant-power-system (Standalone Switch)
user@switch> show chassis redundant-power-system Member Status RPS Port 0 Armed CG0209121807 0
show chassis redundant-power-system (Virtual Chassis member)
user@switch> show chassis redundant-power-system Member Status RPS Port 0 Armed CG0209121814 5 2 Armed CG0209121815 4
show redundant-power-system led
Syntax
Release Information
Command introduced in Junos OS Release 12.1.
Description
Display information about fan status, Redundant Power System (RPS) status, and the switch connectors as displayed by the corresponding LEDs on the RPS.
Required Privilege Level
view
List of Sample Output
show redundant-power-system led (Standalone Switch)show redundant-power-system led (EX3300 Virtual Chassis)
Output Fields
Table 2 lists the output fields for the show redundant-power-system led command. Output fields are listed in the approximate order in which they appear.
Table 2: show redundant-power-system led Output Fields
Field Name | Field Description | Level of Output |
|---|---|---|
RPS | The serial number of the RPS. | |
RPS Fan | Status of the RPS power supply fans as displayed by the LED:
| All levels |
RPS System Status | Status of the RPS system as displayed by the LED:
| All levels |
RPS Port LED Status | Status of the RPS switch connectors as displayed by the LEDs. These LEDs indicate whether the redundant power source is being used.
| All levels |
Port | Number of one of the six switch connectors on the RPS. | All levels |
Status | Status of each switch connector on the RPS. | All levels |
Sample Output
show redundant-power-system led (Standalone Switch)
user@switch> show redundant-power-system led
Gathering requested information.
RPS-CG0209121807
RPS Fan: GREEN
RPS System Status: GREEN
RPS Port LED Status
Port Status
0 GREEN
1 OFF
2 OFF
3 OFF
4 OFF
5 OFF
show redundant-power-system led (EX3300 Virtual Chassis)
user@switch> show redundant-power-system led
Gathering requested information.
RPS-CG0209121814
RPS Fan: GREEN
RPS System Status: GREEN
RPS Port LED Status
Port Status
0 OFF
1 OFF
2 OFF
3 OFF
4 OFF
5 GREEN
RPS-CG0209121815
RPS Fan: GREEN
RPS System Status: GREEN
RPS Port LED Status
Port Status
0 OFF
1 OFF
2 OFF
3 OFF
4 GREEN
5 OFF
show redundant-power-system multi-backup
Syntax
Release Information
Command introduced in Junos OS Release 12.1.
Description
Display the current status of the Redundant Power System’s (RPS’s) ability to back up two switches per power supply when enough power to support Power over Ethernet (PoE) is not needed. This ability is referred to as the RPS’s multi-backup ability.
Required Privilege Level
view
List of Sample Output
show redundant-power-system multi-backupSample Output
show redundant-power-system multi-backup
User@switch> show redundant-power-system multi-backup Requesting information from redundant-power-system.. Multi-Backup: enabled
show redundant-power-system network
Syntax
Release Information
Command introduced in Junos OS Release 12.1.
Description
Display the Redundant Power Supply (RPS) IP address, netmask address, and gateway address required for firmware backup.
Required Privilege Level
view
List of Sample Output
show redundant-power-system networkSample Output
show redundant-power-system network
user@switch> show redundant-power-system network Requesting information from redundant-power-system..
IP Address: 10.93.2.38
Netmask: 255.255.254.0
Gateway: 10.93.3.254
show redundant-power-system power-supply
Syntax
Release Information
Command introduced in Junos OS Release 12.1.
Description
Display information about the power supplies installed in the Redundant Power System (RPS). After installing a power supply, we recommend that you use this command to be sure that the power supply installed correctly.
Required Privilege Level
view
List of Sample Output
show redundant-power-system power-supply (Standalone Switch)show redundant-power-system power-supply (EX3300 Virtual Chassis)
Output Fields
Table 3 lists the output fields for the show redundant-power-system power-supply command. Output fields are listed in the approximate order in which they appear.
Table 3: show redundant-power-system power-supply Output Fields
Field Name | Field Description | Level of Output |
|---|---|---|
RPS | Serial number of the RPS. | All levels |
PSU Slot | Number of the power supply slot. Slots are numbered 1 through 3. | All levels |
Status | Status of the power supply slots:
| All levels |
Description | Description of the RPS power supply installed in the slot. | All levels |
Sample Output
show redundant-power-system power-supply (Standalone Switch)
user@switch> show redundant-power-system power-supply
Gathering requested information.
RPS-CG0209121807
PSU Slot Status Description
1 Online 930W AC
2 offline ---
3 Online 930W AC
show redundant-power-system power-supply (EX3300 Virtual Chassis)
user@switch> show redundant-power-system power-supply
Gathering requested information.
RPS-CG0209121814
PSU Slot Status Description
1 Online 930W AC
2 offline ---
3 Online 930W AC
RPS-CG0209121815
PSU Slot Status Description
1 Online 930W AC
2 Online 930W AC
3 Online 930W AC
show redundant-power-system status
Syntax
Release Information
Command introduced in Junos OS Release 12.1.
Description
Display the status information for the switch connectors on the Redundant Power System (RPS).
Required Privilege Level
view
See also
List of Sample Output
show redundant-power-system status (Standalone Switch)show redundant-power-system status (EX3300 Virtual Chassis)
Output Fields
Table 4 lists the output fields for the show redundant-power-system status command. Output fields are listed in the approximate order in which they appear.
Table 4: show redundant-power-system status Output Fields
Field Name | Field Description | Level of Output |
|---|---|---|
RPS | Serial number of the RPS. | All levels |
Port | Number of the switch connector. | All levels |
Status | Status of the switch connector:
| All levels |
Priority | Priority value of the switch connector. | All levels |
Power-Requested | Power requested by the switch on the corresponding switch connector. | All levels |
Sample Output
show redundant-power-system status (Standalone Switch)
user@switch> show redundant-power-system status Gathering requested information. RPS-CG0209121807 Port Status Power-requested 0 Armed 3 930W 1 Off 1 --- 2 Off 1 --- 3 Off 1 --- 4 Off 1 --- 5 Off 1 ---
show redundant-power-system status (EX3300 Virtual Chassis)
user@switch> show redundant-power-system status Gathering requested information. RPS-CG0209121814 Port Status Power-requested 0 OFF 1 --- 1 OFF 1 --- 2 OFF 1 --- 3 OFF 1 --- 4 OFF 1 --- 5 Armed 5 930W RPS-CG0209121815 Port Status Power-requested 0 OFF 1 --- 1 OFF 1 --- 2 OFF 1 --- 3 OFF 1 --- 4 Armed 4 930W 5 OFF 1 ---
show redundant-power-system upgrade
Syntax
Release Information
Command introduced in Junos OS Release 12.1.
Description
Display RPS firmware upgrade status (pass or fail), previous RPS firmware version, and current RPS firmware version.
Required Privilege Level
view
List of Sample Output
show redundant-power-system upgradeOutput Fields
Table 5 lists the output fields for the show redundant-power-system status command. Output fields are listed in the approximate order in which they appear.
Table 5: show redundant-power-system upgrade Output Fields
Field Name | Field Description | Level of Output |
|---|---|---|
Firmware Upgrade Status | Indicates whether the upgrade passed or failed | All levels |
Previous Firmware Version | Firmware version before the upgrade | All levels |
Current Firmware Version | Firmware version after the upgrade |
Sample Output
show redundant-power-system upgrade
user@switch> show redundant-power-system upgrade
Requesting information from redundant-power-system..
Firmware Upgrade Status: Pass
Previous Firmware Version: 1.0
Current Firmware Version: 1.0
show redundant-power-system version
Syntax
Release Information
Command introduced in Junos OS Release 12.1.
Description
Display version information about the Redundant Power System (RPS).
Required Privilege Level
view
See also
List of Sample Output
show redundant-power-system version (Standalone Switch)show redundant-power-system version (EX3300 Virtual Chassis)
Output Fields
Table 6 lists the output fields for the show redundant-power-system version command. Output fields are listed in the approximate order in which they appear.
Table 6: show redundant-power-system version Output Fields
Field Name | Field Description | Level of Output |
|---|---|---|
RPS | Serial number of the RPS. | All levels |
Model | Model name of the RPS. | All levels |
RPS Firmware Version | Version number of the firmware installed on the RPS. | All levels |
RPS U-Boot Version | Version of the bootup software installed on the RPS. | All levels |
Sample Output
show redundant-power-system version (Standalone Switch)
user@switch> show redundant-power-system version
RPS-CG0209121807
Model: EX-PWR_RPS200
RPS Firmware Version [1.0]
RPS U-Boot Version [1.1.6]
show redundant-power-system version (EX3300 Virtual Chassis)
user@switch> show redundant-power-system version
RPS-CG0209121814
Model: EX-PWR_RPS200
RPS Firmware Version [1.0]
RPS U-Boot Version [1.1.6]
RPS-CG0209121815
Model: EX-PWR_RPS200
RPS Firmware Version [1.0]
RPS U-Boot Version [1.1.6]