QFX5100 Installation Overview
QFX5100 Standalone Installation Overview
You can mount a QFX5100 device:
Flush with the front of a 19-in. four-post rack. Use the standard mounting brackets provided with the switch for this configuration.
Recessed 2 in. (5 cm) from the front of a 19-in. four-post rack. Use the extension bracket provided in the standard mounting kit for this configuration. Recessed mounting is primarily used in enclosed cabinets.
To install and connect a QFX5100 device:
- Follow the instructions in Unpack a QFX5100 Device.
- Determine how the device is to be mounted.
Flush or recessed mounted in a rack or cabinet, see Mount a QFX5100 Device in a Rack or Cabinet.
- Follow the instructions in:
- Depending on how you plan to use the QFX5100 device, do
one of the following:
If you are using the QFX5100 device as a standalone switch, follow the instructions in Configure a QFX5100 Device.
If you are using the QFX5100 device as a Node device in a QFX3000-G QFabric system, see QFX3000-G QFabric System Installation Overview for information about the steps to install and configure your QFX3000-G QFabric system.
If you are using the QFX5100 device as a Node device in a QFX3000-M QFabric system, see QFX3000-M QFabric System Installation Overview for information about the steps to install and configure your QFX3000-M QFabric system.
If you are using a QFX5100-24Q as an Interconnect device in a QFX3000-M QFabric system, see Connecting a QFX5100 Node Device to a QFX5100-24Q Interconnect Device.
If you are using the QFX5100 device in a Virtual Chassis Fabric, see Connecting a QFX5100 Device in a Virtual Chassis Fabric.
Virtual Chassis Fabric Installation Overview
For best results, ensure you review and understand the Virtual Chassis Fabric (VCF) configuration options. These configuration options are explained in Virtual Chassis Fabric Hardware Overview and Understanding Virtual Chassis Fabric Configuration. Do not interconnect the switches with cables until directed in the procedure.
- Install the individual switches in a rack or cabinet following
the guidelines in Plan a Virtual Chassis Fabric Deployment.
Install spine devices at the top of the rack or cabinet in order of primary routing engine (RE), backup RE, and then other leaf devices.
- Make a list of all of the serial numbers of the devices.
- Log into each device and configure into fabric mode and
mixed mode, if needed. Mixed mode is only necessary for QFX5100 VCF
when QFX5100-96S, QFX5100-48T, QFX3500, QFX3600, or EX4300 devices
are present as leaf devices in the configuration. If a spine device
is not properly configured in fabric and mixed mode for QFX5100 mixed
VCF, the VCF devices reboot to commit the mixed mode or fabric settings.
When fabric and mixed mode are not set, you might need to manually
correct any issues that are related to the VCF not forming correctly
because the device did not immediately join the VCF.
Only configure operational-level commands. If you commit any configuration-level commands (including assigning IP address), the Virtual Chassis Fabric cannot form and the switch must be zeroed.
- Configure the VCF into mixed mode if it is a QFX5100 VCF and the switch models span different lines of switches.
- Configure each device for one of the provisioning modes: autoprovision, preprovision, or nonprovision. See:
- Connect and configure one of the management ports (C0) or (C1) to a management switch as the Virtual Management Ethernet interface. Using this interface, you can configure and manage the devices in the VCF. See Connect a Device to a Network for Out-of-Band Management.
- Commit your changes.
- Cable the ports that you will use as VCPs. For cabling
examples, see Connecting QFX5110 in a QFX5110 Virtual Chassis Fabric, Connecting a QFX5100 Device in a Virtual Chassis Fabric, Connecting a QFX3500 or QFX3600 Switch in a QFX5100 Virtual Chassis Fabric,
and Connecting EX Series Switches in a QFX5100 Virtual Chassis Fabric.
If you configured your devices as either autoprovisioned or preprovisioned, the Virtual Chassis ports (VCP) are automatically configured. If you configure the devices as nonprovisioned, you must manually configure the VCPs.
QFX5100 Installation Safety Guidelines
The weight of a 1 U fully loaded QFX5100 switch chassis is approximately 30.8 lb (14 kg); the 2 U product SKU is approximately 32 lbs (14.5 kg). Observe the following guidelines for lifting and moving a QFX5100 switch:
If you are installing the QFX5100 switch above 60 in. (152.4 cm) from the floor, either remove the power supplies, fan modules, and any expansion modules before attempting to install the switch, or ask someone to assist you during the installation.
Before installing a QFX5100 switch, read the guidelines in Site Preparation Checklist for a QFX5100 Device to verify that the intended site meets the specified power, environmental, and clearance requirements.
Before lifting or moving the QFX5100 switch, disconnect all external cables.
As when lifting any heavy object, lift most of the weight with your legs rather than your back. Keep your knees bent and your back relatively straight and avoid twisting your body as you lift. Balance the load evenly and be sure that your footing is solid.