Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Unpack the PTX10008

 

To unpack the PTX10008 router and its components, read the following sections:

Unpack the PTX10008 Shipping Pallet

After you prepare the installation site as described in PTX10008 Site Preparation Checklist, you can unpack the router.

Note

The chassis is maximally protected inside the shipping box. Do not unpack it until you are ready to begin installation.

Ensure that you have the following parts and tools available to unpack the PTX10008:

  • A 13/32-in. (10-mm) open-end or socket wrench to remove the bracket bolts from the shipping pallet

  • A box cutter or packing knife to slice open the nylon straps and tape that seal the crate and boxes

The chassis ships in a cardboard box that has a two-layer wooden pallet base with foam cushioning between the layers. The router chassis is bolted to the pallet base.

The shipper has the option to either ship the front panel separately or ship it along with the chassis. If the front panel arrives with the chassis, set aside the front panel box until you are ready to verify the contents of the order.

To unpack the chassis (see Figure 1):

Figure 1: Shipping Crate and Accessory Box
Shipping Crate and Accessory
Box
  1. Move the shipping box to a staging area as close to the installation site as possible. While the chassis is bolted to the pallet, you can use a forklift or pallet jack to move the shipping box. Make sure there is enough space to remove components from the chassis.
  2. Position the shipping box with the arrows pointing up.
  3. Use the box cuter to slice the nylon straps that hold the shipping box to the pallet.
  4. Lift the shipping box off the chassis.
  5. Remove the cardboard accessory box.
  6. Remove the foam padding from the top of the box.
  7. Remove the plastic cover from the router chassis.
  8. Use a 13/32-in. (10-mm) open-end or socket wrench to remove the four sets of bracket bolts that secure the chassis to the shipping pallet (see Figure 2).
    Figure 2: Remove the Bracket Bolt
    Remove the Bracket
Bolt
  9. Unpack the accessory box and lay out the contents so that they are ready for use.
  10. Verify that your order includes all appropriate parts. See Compare the PTX10008 Order to the Packing List and PTX10008 Components and Configurations for information about base configurations and redundant configurations.
  11. Store the brackets and bolts inside the accessory box.
  12. Save the shipping box and packing materials in case you need to move or ship the router at a later time.

Unpack Line Cards, Routing Control Boards, and Switch Interface Boards for the PTX10008

Line cards, additional Routing and Control Boards (RCBs), and additional Switch Interface Boards (SIBs) components are FRUs that are shipped separately from the router chassis. The housing for the RCBs and line cards are rigid sheet-metal structures that house the electronics. SIBs have an exposed printed circuit board (PCB) on one side and sheet metal on the other. All these components are shipped in a cardboard carton, secured with packing material.

Caution

The components are maximally protected inside the shipping carton. Do not unpack them until you are ready to install the components in the router chassis.

Before you unpack a component:

To unpack an RCB, a SIB, or a line card, (see Figure 3):

  1. Move the shipping carton to a staging area as close to the installation site as possible.
  2. Position the carton so that the arrows are pointing up.
  3. Open the top flaps on the shipping carton.
  4. Pull out the packing material that holds the component in place.
  5. Remove the component from the antistatic bag.
  6. Save the shipping carton and packing materials in case you need to move or ship the RCB, SIB, or line card later.
Figure 3: Unpacking a Line Card
Unpacking a Line Card
  1
Foam packing material
  2
Paper packaging and antistatic bag

Compare the PTX10008 Order to the Packing List

The router chassis shipment includes a packing list. Check the parts you receive in the shipping crate against the items on the packing list. The packing list specifies the part number and description of each part in your order.

If any part on the packing list is missing, contact your customer service representative, or contact Juniper Networks Customer Care from within the U.S. or Canada by telephone at 1-888-314-5822. For international-dial or direct-dial options in countries without toll-free numbers, see https://www.juniper.net/support/requesting-support.html.

Items that ship separately from the chassis are:

  • Line cards

  • Chassis front panel kit (JNP10008-FRNT-PNL)

    Note

    The kit is a spare part and can ship with the chassis or separately.

    Cable management kit (JLC-CBL-MGMT-KIT)

Use the following procedure to compare the sales order and packing list against the contents of the chassis shipping crate.

  1. Determine the configuration. See PTX10008 Hardware Configurations. The parts shipped depend on the configuration you order. Supported configurations are:
    • Base configuration.

      • PTX10008-BASE for AC and JNP10008-SF fabric systems.

      • PTX10008-BASE for DC and JNP10008-SF fabric systems.

    • Premium redundant configuration.

      • PTX10008-PREMIUM for AC and JNP10008-SF fabric systems.

      • PTX10008-PREMIUM for DC and JNP10008-SF fabric systems.

      • PTX10008-PREM3 for AC and JNP10008-SF3 fabric systems.

      • PTX10008-PREM3 for DC and JNP10008-SF3 fabric systems.

  2. Compare premium redundant configuration orders using Table 1.

    Table 1: Premium Redundant Configuration Order

    Component

    PTX10008 Quantity

    Chassis, including power bus

    1

    Routing and Control Boardss

    2

    Fan tray controllers

    • JNP10008-FAN-CTRL or

    • JNP10008-FTC2

    2

    Fan trays

    • JNP10008-FAN or

    • JNP10008-FAN2

    2

    Power supplies

    • JNP10K-PWR-AC

    • JNP10K-PWR-AC2

    • JNP10K-PWR-DC

    • JNP10K-PWR-DC2

    6

    Switch Interface Boards (SIBs)

    6

    Covers in the line-card positions

    8

    Accessory kit (see Table 3)

    1

    Rack mount kit (see Table 4)

    1

    Front panel kit (see Table 5)

    1

    Documentation Roadmap Card

    1

  3. Compare base configuration orders using Table 2.

    Table 2: Base Configuration Order

    Component

    PTX10008 Quantity

    Chassis, including power bus

    1

    RCBs

    1

    Cover panel, in the RCB slot

    1

    Fan tray controllers

    2

    Fan trays

    2

    Power supplies

    3

    SIBs

    5

    Cover in a SIB position

    1

    Covers in the power-supply positions

    3

    Covers in the line-card positions

    8

    Dust covers for RCB ports

    5 for RE0; 3 for RE1

    Accessory kit (see Table 3)

    1

    Rack mount kit (see Table 4)

    1

    Front panel kit, lockable (see Table 5)

    1

    Documentation Roadmap Card

    1

  4. Compare the contents of the accessory kit with Table 3.

    Table 3: PTX10008 Accessory Kit

    Component

    Quantity

    AC Configurations

    DC Configurations

    Warranty card

    1

    1

    End User License Agreement (EULA)

    1

    1

    RJ-45 Ethernet cable

    1

    1

    RJ-45 to DB9 rollover cable

    1

    1

    Electrostatic discharge (ESD) wrist strap with cable

    1

    1

    Media kit (flash drives, PCMCIA card adapter)

    1

    1

    Chassis ground lug, 2-hole, 10-32, 6 AWG

    1

    1

    Power cord retainer clips

    Premium = 12

    Base = 6

    DC terminal lugs, 2-hole, 10-32, 4 AWG

    Premium = 24

    Base = 12

    Antistatic bags

    2

  5. Compare the contents of the rack mount kit with Table 4.

    Table 4: PTX10008 Rack Mount Kit

    Component

    Quantity

    Phillips flat-head screws, 8-32 x 375 in.

    12

    Rear brackets

    2

    Right base bracket

    1

    Left base bracket

    1

  6. Compare the contents of the front panel kit with Table 5.

    Table 5: PTX10008 Front Panel Kit

    Component

    Quantity

    Front panel

    1

    Left base bracket

    1

    Right base bracket

    1

    Latch brackets

    2

    Phillips flat-head screws

    8

    Documentation Roadmap Card

    1

Registering Products—Mandatory for Validating SLAs

Register all new Juniper Networks hardware products and changes to an existing installed product using the Juniper Networks website to activate your hardware replacement service-level agreements (SLAs).

Caution

Register product serial numbers on the Juniper Networks website and update the installation base data if there is any addition or change to the installation base or if the installation base is moved. Juniper Networks will not be held accountable for not meeting the hardware replacement service-level agreement for products that do not have registered serial numbers or accurate installation base data.

Register your product(s) at https://tools.juniper.net/svcreg/SRegSerialNum.jsp.

Update your installation base at https://www.juniper.net/customers/csc/management/updateinstallbase.jsp.