Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

PTX1000 Management Panel

 

PTX1000 Management Panel

The PTX1000 management panel is found next to the port panel (see Figure 1).

Figure 1: PTX1000 Port Panel and Management Panel
PTX1000 Port Panel and Management
Panel
  1
Port panel
  2
Management panel

You manage the PTX1000 by using the Junos OS CLI, which is accessible through the console and out-of-band management ports on the management panel. In addition, the management panel has system status LEDs that alert you to minor or major alarms or other issues with the router, external clock synchronization ports, and a USB port to support software installation and recovery. Figure 2 shows the management panel in detail.

Figure 2: PTX1000 Management Panel Components
PTX1000 Management Panel Components
  1
RJ-45 (1000BASE-T) management Ethernet port (labeled MGMT). In the Junos OS CLI, this port is identified as em0.
  6
SFP PTP Ethernet (1000BASE-T) port (labeled ETH). Port reserved for future use.
  2
RJ-45 console port (CON) to support RS-232 serial ports.
  7
10 Hz pulses-per-second (PPS) SubMiniature B (SMB) connector for input and output measuring of the timing drift to and from a grandmaster clock. Port reserved for future use.
  3
Reset button. Press and hold 5 seconds to reset the hardware. Clock functions and FPGA status registers are not reset.
  8
10 MHz SMB timing connector (10MHz). Port reserved for future use.
  4
Status LEDs—Power (PWR), status (STS), major alarm (MAJ), and minor alarm (MIN).
  9
USB port.
  5
SFP management Ethernet port (labeled MGMT). In the Junos OS CLI, this port is identified as em1.
 

PTX1000 Management Port LEDs

There are two management ports on the PTX1000, located on the management panel next to the network ports. Both ports are labeled MGMT. The RJ-45 management port is for 10/100/1000BASE-T connections and the small form-factor pluggable (SFP) management port is for 10/100/1000BASE-T and 1000BASE-X connections.

The RJ-45 port has separate LEDs for status and activity. The SFP port has a LED to indicate both link and activity. Figure 3 shows the location of the LEDs.

Figure 3: Management Port LEDs on a PTX1000
Management Port LEDs on a PTX1000
  1
Status LED (RJ-45)
  3
Link activity LED (SFP)
  2
Link activity LED (RJ-45)
 

Table 1 describes the RJ-45 management port LEDs.

Table 1: PTX1000 RJ-45 Management Port LEDs

LED

Color

State

Description

Link activity

Unlit

Off

No link is established, there is a fault, or the link is down.

Amber

Blinking or flickering

A link is established, and there is link activity.

Status

Unlit

Off

Either the port speed is 10 Mbps or the link is down.

Green

On steadily

The port speed is 1000 Mbps.

Table 2 describes the SFP management port LED.

Table 2: PTX1000 SFP Management Port LED

LED

Color

State

Description

Link activity

Unlit

Off

No link is established, there is a fault, or the link is down.

Green

On steadily

A link is established, but there is no link activity.

Blinking or flickering

A link is established, and there is link activity.

PTX1000 Chassis Status LEDs

The PTX1000 has four status LEDs on the management panel of the chassis, next to the network ports (see Figure 4).

Figure 4: Chassis Status LEDs on a PTX1000
Chassis Status LEDs on
a PTX1000
  1
Power (PWR) LED
  3
Minor alarm (MIN) LED
  2
Major alarm (MAJ) LED
  4
Status (STS) LED

Table 3 describes the chassis status LEDs on a PTX1000.

Table 3: PTX1000 Chassis Status LEDs

Name

Color

State

Description

Power (PWR)

Unlit

Off

The PTX1000 is powered off— there is no power to the device.

Green

On steadily

The power system is working correctly.

Amber

Blinking

There is a problem with the power system. Power off the PTX1000 by setting the AC power source outlet to the off (O) position or by unplugging the AC power cords. Correct any voltage issues. Power on the PTX1000 and monitor the power supply and fan LEDs to help determine where the error is occurring. If there is a CPU power failure, the PTX1000 does not boot.

Status (STS) LED

Unlit

Off

The PTX1000 is powered off or Junos OS is halted.

Green

On steadily

Junos OS has booted.

Amber

Blinking

The PTX1000 detects a fault.

Major alarm (MAJ) LED

Unlit

Off

There are no major alarms.

Red

On steadily

A major hardware fault has occurred, such as a temperature alarm or power failure, and the PTX1000 has halted.

Minor alarm (MIN) LED

Unlit

Off

There are no minor alarms.

Amber

On steadily

A minor alarm has occurred, such as a software error.