Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 
 

MX2008 Chassis

MX2008 Chassis Description

The router chassis is a rigid sheet metal structure that houses all the other router components (see Figure 1, Figure 2, and Figure 3). The MX2008 Universal Routing Platform with standard cable managers and EMI cover measures 42  in.  (106.68 cm) high, 19  in.  (48.26 cm) wide, and 30.90  in.  (78.49 cm) deep (from the front-mounting flanges to the rear of the chassis). An extended cable manager extends the total depth to 36.82  in. (93.53 cm). The chassis can be installed in a standard 19-in.  open-frame or four-post rack, or an enclosed cabinet.

Note:

There must be a minimum of 24 rack units (U) of usable rack space when installing the MX2008 router into a rack.

Note:

If you are installing the MX2008 router into a network cabinet, make sure that no hardware, device, rack, or cabinet component obstructs the 24  U rack space from access during installation.

The chassis includes the following features (see Figure 1, Figure 2, and Figure 3).

  • Front-mounting flanges for mounting in a four-post rack or cabinet.

  • Center-mounting metal brackets for center-mounting in an open-frame rack (optional).

CAUTION:

Before removing or installing components, attach an electrostatic discharge (ESD) strap to an ESD point, and place the other end of the strap around your bare wrist. Failure to use an ESD strap could result in damage to the hardware components.

Warning:

The router must be connected to earth ground during normal operation.

The MX2008 router is 24 rack units (U) tall. One router can be installed in an open-frame rack, four-post rack, or cabinet. The MX2008 router has 10 dedicated line-card slots, which means a maximum of 10 Modular Port Concentrators (MPCs) including adapter cards and Modular Interface Cards (MICs) can be installed on MX2008. ADCs provide housing to MPCs. The MPCs attach to the adapter cards, which in turn connect to the backplane. Up to 2 MICs can be installed in each MPC. Fully populated, the MX2008 router supports up to 20 MICs. The MX2008 host subsystem consists of two Routing and Control Boards (RCBs). The RCB is an integrated board and a single FRU that provides Routing Engine and Control Board functionality and supports virtualization. The router contains 8 SFBs that provide 7+1 redundancy.

One router can be installed in a 24  U or taller open-frame or four-post rack if the rack can support the combined weight, which can be greater than 664.8  lb (301.55 kg).

Note:

The dimensions also include the cable managers and EMI cover.

Figure 1: Front View of a Fully Configured MX2008 Router ChassisFront View of a Fully Configured MX2008 Router Chassis
Note:

Remove field-replacement units (FRUs) from the front of the MX2008 router before you install the router.

See Table 1 for information about the components on the front of the MX2008 router.

Table 1: Front Components in a Fully Configured MX2008 Router

Component No.

Component Description

Slots

Number of FRUs

1

Craft interface

1

2

Enhanced Switch Fabric Board (SFB2)

0 through 7

8

3

Routing and Control Boards (RCB)

0 and 1

2

4

MPCs (with MICs installed)

0 through 9

10

5

Cable manager

1

See Table 2 for information about components on the back of an AC-powered MX2008 router.

Figure 2: Rear View of a Fully Configured AC-Powered MX2008 Router Chassis Rear View of a Fully Configured AC-Powered MX2008 Router Chassis
Table 2: Rear Components in a Fully Configured AC-Powered MX2008 Router

Component No.

Component Description

Slots

Number of FRUs

1

AC PDM—Three-phase delta or wye, or a single-phase AC PDM, or a high-voltage second-generation universal (HVAC/HVDC) PDM

PDM1/Input1

1

2

AC PSMs or high-voltage second-generation universal (HVAC/HVDC) PSMs

0 through 8

9

3

PSM air filter

1

4

AC PDM—Three-phase delta or wye, or a single-phase AC PDM, or a high-voltage second-generation universal (HVAC/HVDC) PDM

PDM0/Input0

1

5

Fan tray air filter

1

6

Fan trays (two)

Fan tray 0 and fan tray 1 (behind access door)

2

Note:

Remove field-replacement units (FRUs) from the rear of the MX2008 router before you install the router.

Figure 3: Rear View of a Fully Configured DC-Powered MX2008 Router Chassis Rear View of a Fully Configured DC-Powered MX2008 Router Chassis
Note:

Remove field replacement units (FRUs) from the rear of the MX2008 router before you install the router.

See Table 3 for information about router components on the back of a DC-powered MX2008 router.

Table 3: Rear Components in a Fully Configured DC-Powered MX2008 Router

Component No.

Component Description

Slots

Number of FRUs

1

DC PDM, a DC PDM (240 V China), or a high-voltage second-generation universal (HVAC/HVDC) PDM

PDM1/Input1

1

2

DC PSMs, DC PSMs (240 V China), or high-voltage second-generation universal (HVAC/HVDC) PSMs

0 through 8

9

3

PSM air filter

1

4

DC PDM, a DC PDM (240 V China), or a high-voltage second-generation universal (HVAC/HVDC) PDM

PDM0/Input0

1

5

Fan tray air filter

1

6

Fan trays (two)

Fan tray 0 and fan tray 1 (behind access door)

2

Note:

Remove field replacement units (FRUs) from the rear of the MX2008 router before you install the router.

The MX2008 router has two ESD points. These are located on either side of the MPCs on the front of the chassis (see Figure 4).

Figure 4: MX2008 Router ESD PointsMX2008 Router ESD Points

MX2008 Backplane Description

The MX2008 router consist of a signal backplane and a power backplane that connect PSMs and PDMs to the chassis. The adapter cards are carrier cards used to house the MPCs. The MPCs install into the bottom card-cage signal backplanes from the front of the chassis and mate to the signal backplane to connect to the Enhanced Switch Fabric Boards (SFB2s) and the Routing and Control Boards (RCBs). The backplane connects 10 line cards to 8 SFBs and 2 RCBs. The SFBs and RCBs are installed at the top of the chassis from the front. The cooling system components also connect to the signal backplane. The PSMs install into the power backplane, and the PDMs mate to the power backplane.

The backplanes performs the following major functions:

  • Data path—Data packets are transferred across the signal backplane between the MPCs through the fabric ASICs on the SFBs.

  • Power distribution—The router PDMs relay power from the feeds to the input of the PSMs through the power backplane. In addition, the output power from PSMs is distributed to the components of the chassis (MPCs, SFBs, and RCBs), using the power backplane.

  • Control/management path—The backplanes provides management and control path connectivity among the various system components.

MX2008 Component Redundancy

A fully configured router is designed so that no single point of failure can cause the entire system to fail. Only a fully configured router provides complete redundancy. All other configurations provide partial redundancy. The following major hardware components are redundant:

  • Host subsystem—The host subsystem consists of two Routing and Control Boards (RCBs). The RCB is an integrated board and a single FRU that provides Routing Engine and Control Board functionality. The router can have one or two host subsystems. If two host subsystems are installed, one functions as the primary and the other functions as the backup. If the primary host subsystem (or either of its components) fails, the backup can take over as the primary.

  • DC power system—The MX2008 DC power system (-48 V and 240 V China) is made up of three components: nine power supply modules (PSMs), two power distribution modules (PDMs), and a power midplane. For telecom (48 VDC) power supplies the power system distributes power from a pool of 22.5 KW (20 KW for non-redundant PSMs and 2.5 KW reserved for PSM redundancy). This pool provides power to the whole chassis including the ten line-card slots, two fan trays, and critical FRUs. These critical FRUs consist of two RCBs and eight SFBs located in the top portion of the chassis.

  • Power distribution modules (PDMs)—In the DC configuration, each system provides N+1 PSM redundancy along with N+N feed redundancy. The power feeds from different sources need to be connected to different PDMs. If feeds that connect to one PDM fail in a redundant configuration, the other feed starts to provide full power.

    Note:

    Depending on the voltage of the DC feeds, power can be drawn from both feeds. The feed with higher voltage provides more power. If the difference between the voltages is sufficient, then the higher voltage feed provides all the power. When the voltages are exactly the same, equal power is drawn from both feeds.

    A total of two PDMs can be installed into a router. Each DC PDM operates with up to nine separate feeds of either 60-A or 80-A current limit. The 240 V China DC PDMs have nine feeds and do not have a switch selection. The capacity of these feeds is relayed to system software through a switch located on the DC PDM.

    The MX2008 router supports two types of three-phase power system PDMs. The three-phase delta and three-phase wye. Individual phases are taken from three-phase feeds to individual PSMs. One feed provides power to six PSMs, while the second input feed provides power to the remaining three PSMs (supporting a total of nine PSMs).

  • DC power feed redundancy—The MX2008 DC power system is feed redundant. Each PSM can be connected to two separate feeds from different sources that are used to provide feed redundancy. There are two PDMs per power subsystem that carry nine feeds each. Feeds from one power source must be connected to one PDM and feeds from the other power source must be connected to the second PDM of the power subsystem (see Figure 5).

    Figure 5: DC Power System Feed RedundancyDC Power System Feed Redundancy

    Each PSM has a set of two DIP switches located on the faceplate. These DIP switches are used to indicate whether a user wants to connect one feed to the power system, two feeds, or none. These DIP switches provide critical information to the power management system to help generate alarms in case of a feed failure or a wrong connection. Each PDM has an LED per feed indicating whether the feed is active or not, or whether the feed is connected properly. See MX2008 DC Power Supply Module (-48 V) Description.

  • Universal power system—The MX2008 supports connection of a high-voltage second-generation universal (HVAC/HVDC) power system.

    High-Voltage Second-Generation Universal (HVAC/HVDC) PDMs—The universal PDM accepts either an HVAC or HVDC input. You can install a total of two PDMs into a router. Each universal PDM operates with nine feeds of a 30-A current limit. Each universal PSM is capable of delivering 3400 W of power with-dual feeds and 3000 W of power with a single-feed. In this configuration, each subsystem provides N+1 output PSM redundancy along with N+N feed redundancy. The power feeds from different sources need to be connected to different PDMs. If feeds that connect to one PDM fail in a redundant configuration, the other feed provides full power. For high-voltage second-generation universal (HVAC/HVDC) power system, both input power feeds are active and share the load when present.

    Figure 6 illustrates the power distribution from the universal (HVAC/HVDC) PDMs to the universal (HVAC/HVDC) PSMs.

    Figure 6: MX2010 Router Universal (HVAC/HVDC) Power Subsystem Feed RedundancyMX2010 Router Universal (HVAC/HVDC) Power Subsystem Feed Redundancy
  • AC power system—The MX2008 supports connection of three-phase and single-phase AC power systems.

    There are two types of three-phase power systems: the three-phase delta and three-phase wye. The AC power going to the PSMs is split into three individual phases—each PSM works on a single phase. This means the power system works independent of the kind of AC feed is connected. You can connect one or two feeds, depending on the power system configuration (number of PSMs, redundancy, and so on). Each phase from each of the two feeds is distributed among one or two PSMs (one feed has each phase going to two PSMs, and the other feed has each phase going to a single PSM). See Figure 8 and Figure 9.

    The single-phase AC PDM provides an AC input power interface to the PSM through the system power midplane. Up to nine PSMs can be connected to a single-phase AC PDM. Each single-phase AC PDM accepts seven or nine AC power cords from a single-phase AC source. Each AC input is independent and feeds one PSM. See Figure 7.

    Figure 7: Power Distribution from Single-Phase Feed Delta PDM to the AC PSMsPower Distribution from Single-Phase Feed Delta PDM to the AC PSMs
    Figure 8: Power Distribution from Three-Phase Feed Delta PDM to the AC PSMsPower Distribution from Three-Phase Feed Delta PDM to the AC PSMs
    Figure 9: Power Distribution from Three-Phase Feed Wye PDM to the AC PSMsPower Distribution from Three-Phase Feed Wye PDM to the AC PSMs

    The AC power system is feed redundant—each PSM takes in two AC feeds and uses one of the two. One AC feed is active at a time. If one feed fails, the PSM automatically switches over to the other feed without disrupting system function (see MX2008 AC Power Supply Module Description).

  • AC power requirements—Table 4 shows the MX2008 current requirements for the three-phase delta and wye power feeds.

    Table 4: AC PDM Delta and Wye Current Requirements

    Three-Phase Voltage

    Input Feed

    Current Delta per Three-Phase PDM

    Current Wye per Three-Phase PDM

    200 V (minimum–nominal) (line-to-line) for delta (per phase)

    1

    50 A

    2

    25 A

    200 V (minimum–nominal) (line-to-neutral) for wye (per phase)

    1

    30 A

    2

    15 A

    Note:

    This is the minimum required to provide 2.5 KW per PSM. Based on facilities guidelines, you should overprovision the MX2008 router. The two numbers listed in the current columns reflect the distribution of phases from the feed to PSM. For example, from one feed each phase goes to two PSMs and from the other feed each phase goes to only one PSM.

  • Power supply modules (PSMs)—All nine AC, DC, 240 V China, or universal HVAC/HVDC PSMs in a system share the load. If one PSM fails in a redundant configuration, the remaining eight PSMs provide power to FRUs. Up to nine PSMs might be required to supply power to a fully configured router. Nine PSMs supply power to the two RCBs (active and redundant), eight SFBs, ten MPCs, and two fan trays (active and redundant).

  • Cooling system—The cooling system has a total of two fan trays—which are controlled and monitored by the host subsystem. The fan trays are at the bottom and are used to cool RCBs, SFBs, and ten line cards. If a fan fails or the temperature rises above the temperature threshold, the speed of the remaining fans is automatically adjusted to keep the temperature within the acceptable range (see MX2008 Cooling System Description).

Note:

The MX2008, MX2010, and MX2020 routers support the same power modules (AC/DC or HVAC/HVDC PSMs and PDMs).

MX2008 Field-Replaceable Units

Field-replaceable units (FRUs) are router components that can be replaced at the customer site (see Table 5). Replacing most FRUs requires minimal router downtime. The router uses the following types of FRUs:

  • Hot-removable and hot-insertable FRUs—You can remove and replace these components without powering off the router or disrupting the routing functions.

  • Hot-pluggable FRUs—You can remove and replace these components without powering off the router, but the routing functions of the system are interrupted when the component is removed.

    Note:

    Before you replace most host subsystem components, such as the RCBs, you must take the host subsystem offline.

Table 5 lists the FRUs for the MX2008 router.

Table 5: Field-Replaceable Units

Hot-Removable and Hot-Insertable FRUs

Hot-Pluggable FRUs

  • PSM air filter

  • Air filter (lower)

  • Lower cable manager

  • Craft interface

  • Switch Fabric Board (SFB) (if redundant)

  • Backup RCB (if redundant)

  • Primary RCB (if nonstop active routing is configured)

  • Modular Port Concentrators (MPCs)

  • Adapter cards

  • Modular Interface Cards (MICs)

  • AC power supply modules (if redundant)

  • AC power distribution modules (if redundant)

  • DC (-48 V) power supply modules (if redundant)

  • DC (-48 V) power distribution modules (if redundant)

  • DC (240 V China) power supply modules (if redundant)

  • DC (240 V China) power distribution modules (if redundant)

  • Universal (HVAC/HVDC) power supply modules (if redundant)

  • Universal (HVAC/HVDC) power distribution modules (if redundant)

  • Fan trays

  • Routing and Control Boards (RCB) (nonredundant)

  • Switch Fabric Board (SFB) (nonredundant)

MX2008 Router Hardware Components and CLI Terminology

The MX2008 router supports the components listed in Table 6.

Table 6: MX2008 Router Hardware Components and CLI Terminology

Component

Hardware Model Number

CLI Name

Description

Chassis

Chassis

CHAS-MX2008

MX2008

MX2008 Physical Specifications

MX2008 Chassis Description

AC optimized power chassis

MX2008-PREMIUM2-AC

DC optimized power chassis

MX2008-PREMIUM2-DC

Craft interface panel

MX2008-CRAFT

Front Panel Display

MX2008 Craft Interface Description

Cooling System, Including Air Baffle, Fan Trays, and Air Filters

Fan tray

MX2000-FANTRAY

172 mm FanTray - 6 Fans

MX2008 Cooling System Description

Optimized power fan tray

MX2K-FANTRAY

Optimized Power fan tray

Air filter kit

MX2000-FLTR-KIT-S

N/A

Power System Components

MX2008 Power System Description

PDM blank cover

MX2000-PDM-BLANK

N/A

MX2008 DC Power Distribution Module (-48 V) Description

Power distribution module (PDM)

MX2000-PDM-DC

DC 52V Power Dist Module

MX2K-PDM-DC240V

MX2K 240V HVDC PDM

MX2000 DC Power Distribution Module (240 V China) Description

MX2K-PDM-HV

MX2K UNIVERSAL HV PDM

MX2008 High-Voltage Universal (HVAC/HVDC) Power Distribution Module Description

MX2000-PDM-AC-DELTA

AC Delta Power Dist Module

MX2008 Three-Phase Delta AC Power Distribution Module Description

MX2000 Three-Phase Delta AC Power Distribution Module Description

MX2000-PDM-AC-WYE

AC Y Power Dist Module

MX2008 Three-Phase Wye AC Power Distribution Module Description

MX2000 Three-Phase Wye AC Power Distribution Module Description

MX2K-PDM-AC-1PH

Single-phase AC PDM

 

MX2K-PDM-OP-AC

Single-phase AC PDM (6+1)

 

MX2K-PDM-OP-DC

Optimized Power DC PDM (6+1)

 

PSM blank cover

MX2000-PSM-BLANK

N/A

MX2008 Power System Description

Power supply module (PSM)

MX2000-PSM-AC

AC 52V Power Supply Module

MX2000-PSM-DC

DC 52V Power Supply Module

MX2K-PSM-DC240V

MX2K 240V HVDC PSM

MX2000 DC Power Supply Module (240 V China) Description

MX2K-PSM-HV

MX2K UNIVERSAL HV PSM

MX2008 High-Voltage Universal (HVAC/HVDC) Power Supply Module Description

MICs and MPCs, Including ADC and Transceiver

MIC

See MX Series Interface Module Reference

MX2008 Modular Interface Card Description

MPC blank cover

MX2000-LC-BLANK

N/A

MX2008 Modular Port Concentrator Description

MPC

See MX Series Interface Module Reference

ADC

MX2000-LC-ADAPTER

Adapter Card

MX2000 Adapter Card (ADC) Description

Transceiver

See MX Series Interface Module Reference

Xcvr

Connecting MPC or MIC Cables to the MX2008 Router

Host Subsystem Components

SFB

MX2008-SFB2

MX2008 Switch Fabric Board 2

MX2008 Enhanced Switch Fabric Board (MX2008 SFB2) Description

SFB blank cover

MX2008-RE-SFB-BLANK

N/A

Routing and Control Board (RCB)

REMX2008-X8-64G

Control Board

MX2008 Routing and Control Board (MX2008 RCB) Description

Routing Engine

RE-MX2008-X8-64G

MX2008 Craft Interface Description

The craft interface enables the user to view status and troubleshooting information at a glance and to perform many system control functions. It is hot-insertable and hot-removable.

The craft interface is located on the front of the router and contains LEDs for the router components, the alarm relay contacts, and alarm cutoff button (see Figure 10). Table 7 describes the LEDs, buttons, and connectors.

Figure 10: Front Panel of the Craft InterfaceFront Panel of the Craft Interface
Table 7: Craft Interface LEDs, Buttons, and Connectors

Function No.

Label

Description

1

PSM

Status LEDs for PSMs 0 through 8

2

FANTRAYS

Status LEDs for fan trays 0 and 1

3

RE0 (MASTER, ONLINE, and OFFLINE)

RE1 (MASTER, ONLINE, and OFFLINE)

Two sets of status LEDs per host subsystem. There are three LEDs per Routing Engine.

4

MINOR ALARM

Minor Alarm LED for monitoring or maintaining the MX2008

5

MAJOR ALARM

Major Alarm LED for critical conditions, which can result in system shutdown

6

ACO/LT

Alarm Cutoff/ Lamp Test button. Turns off both minor and major alarms and deactivates the device attached to the corresponding alarm relay contact on the craft interface

7

M/S CHASSIS NUM

Chassis ID Dial and Standalone Dial. One dial is used to indicate the chassis number for multichassis configurations. The second dial is used to indicate whether the chassis is operating in standalone mode or as part of a multichassis system.

8

MINOR ALARM–[NC C NO]

MAJOR ALARM–[NC C NO]

Two sets of alarm terminal contacts, each consisting of normal open and normal closed relays that signal a minor or major alarm when broken.

9

CB-RE 0 and CB-RE 1

Status LEDs for the two RCBs.

10

LC 0 through LC 9

Status LEDs for the ten line cards.

11

SFB 0 through SFB 7

Status LEDs for eight SFBs.

MX2008 Alarm Relay Contacts on the Craft Interface

The craft interface has two alarm relay contacts for connecting the router to external alarm devices (see Figure 11). Whenever a system condition triggers either the red or yellow alarm on the craft interface, the alarm relay contacts are also activated. The alarm relay contacts are located on the upper right of the craft interface (see Table 8).

Figure 11: Alarm Relay ContactsAlarm Relay Contacts
Table 8: Alarm Relay Contacts

Function No.

Label

Description

1

MINOR ALARM–[NC C NO]

MAJOR ALARM–[NC C NO]

The alarm relays consist of three terminal contacts with normal closed (NC), common (C), and normal open (NO) relays that signal a minor or major alarm when broken.

MX2008 Alarm LEDs and Alarm Cutoff/Lamp Test Button

Two large alarm LEDs are located at the upper right of the craft interface. When lit, the circular red LED indicates a critical condition that can result in a system shutdown. A lit triangular yellow LED indicates a less severe condition that requires monitoring or maintenance. Both LEDs can be lit simultaneously.

A condition that causes an LED to light also activates the corresponding alarm relay contact on the craft interface.

To deactivate red and yellow alarms, press the button labeled ACO/LT (for “alarm cutoff/lamp test”), which is located to the right of the alarm LEDs. Deactivating an alarm turns off both LEDs and deactivates the device attached to the corresponding alarm relay contact on the craft interface.

Table 9 describes the alarm LEDs and alarm cutoff button in more detail.

Table 9: Alarm LEDs and Alarm Cutoff/Lamp Test Button

Shape

Color

State

LED Control Name

Description

Red

On steadily

Critical alarm

Indicates a critical condition that can cause the router to stop functioning. Possible causes include component removal, failure, or overheating.

Yellow

On steadily

Warning alarm

Indicates a serious but nonfatal error condition, such as a maintenance alert or a significant increase in component temperature.

Alarm cutoff/lamp test button

Deactivates red and yellow alarms. Causes all LEDs on the craft interface to light (for testing) when pressed and held.

MX2008 Component LEDs on the Craft Interface

MX2008 Host Subsystem LEDs and Buttons on the Craft Interface

Each host subsystem has three LEDs, located in the upper middle of the craft interface, that indicate its status. The LEDs labeled RE0 show the status of the Routing Engine on the RCB in slot 0. The LEDs labeled RE1 show the status of the Routing Engine on the RCB in slot 1. Table 10 describes the functions of the host subsystem LEDs.

Table 10: Host Subsystem LEDs on the Craft Interface

Label

Color

State

Description

MASTER

Green

On steadily

Host is functioning as the primary.

ONLINE

Green

On steadily

Host is online and is functioning normally.

OK/FAIL

Red

On steadily

Host is installed but the Routing Engine on the RCB is offline.

Off

Host is not installed.

If you need to take the Control Board offline, you must first take the Routing Engine offline. The Routing Engine gets powered by the Control Board. The RCB is an integrated board and a single FRU that provides Routing Engine and Control Board functionality.

MX2008 Power Supply Module LEDs on the Craft Interface

Each power supply module (PSM) has one bicolor LED on the craft interface that indicates its status. The LEDs, labeled 0 through 8, are located on the upper left of the craft interface next to the PSM label. Table 11 describes the functions of the PSM LEDs on the craft interface.

Table 11: Power Supply Module LEDs on the Craft Interface

Label

Color

State

Description

PSM

Green

On steadily

PSM is functioning normally.

Red

On steadily

PSM module has failed or power input has failed.

MX2008 Line-Card LEDs and Buttons on the Craft Interface

Each line card (or MPC) has one bicolor LED on the craft interface that indicates its status. The LEDs, labeled LC 0 through LC 9, are located along the bottom of the craft interface. Table 12 describes the functions of the LEDs present on the MPC.

Table 12: Line-Card LEDs on the Craft Interface

Label

Color

State

Description

LC

Green

On steadily

Line card functioning normally.

Blinking

Line card is transitioning online or offline.

Off

The slot is not online.

Red

On steadily

Line card has failed.

There are ten push buttons located next to each of the line card LEDs on the craft interface. These buttons are used to place the line cards online or offline. When a line card is inserted into an adapter card, and installed into the MX2008 router, the online/offline buttons can turn both the line card and its adapter card on or off.

Note:

When installing an adapter card without the line card, the online/offline buttons have no effect.

MX2008 SFB LED and Buttons on the Craft Interface

Each SFB has one bicolor LED on the craft interface that indicates its status. The SFB LEDs, labeled 0 through 7, are located along the bottom of the craft interface. Table 13 describes the functions of the SFB LED.

Table 13: SFB LED on the Craft Interface

Label

Color

State

Description

SFB

Green

On steadily

SFB functioning normally.

Blinking

SFB is transitioning online or offline.

Off

The slot is not online.

Red

On steadily

SFB has failed.

There are eight push buttons located next to each of the SFB LEDs on the craft interface. These buttons are used to place the SFBs online or offline.

MX2008 Fan Tray LEDs on the Craft Interface

The fan tray LEDs, labeled 0 and 1, are located on the top middle of the craft interface. Table 14 describes the functions of the fan tray LEDs.

Table 14: Fan LEDs on the Craft Interface

Label

Color

State

Description

FANTRAYS

Green

On steadily

Fan is functioning normally.

Red

On steadily

Fan in a fan tray has failed.

Fan tray has failed.

MX2008 Cable Manager Description

The MX2008 router supports the following cable managers:

Note:

The MX2008, MX2010, and MX2020 routers support the same cable managers.

Standard Cable Manager

The standard cable manager consists of the following components:

  • Card-cage cable manager—MX2000-CBL-MID

  • Lower cable manager—MX2000-CBL-BTM-S

  • DC power cable manager—MX2000-DC-CBL-MGR-S

  • Cable manager for the DC PDM (240 V China) and the universal (HVAC/HVDC PDM)—MX2K-HV-CBL-MGR

The lower cable manager (see Figure 12) is located just below the lower card cage, has a removable cover that is secured by two captive screws with access to rows used for routing and securing the cables away from the front of the Modular Port Concentrators (MPCs) and Modular Interface Cards (MICs) (see Figure 13).

You can use cable strips or other ties to gently secure the cables in the lower cable manager. To secure the cables in place, loop the tie through the cable anchor and secure the tie.

Each DC PDM has one cable manager. The DC cable manager routes cables away from the rear of the PDMs (see Figure 12).

You can use cable strips or other ties to gently secure the cables in the DC cable manager. To secure the cables in place, loop the tie through the cable anchor and secure the tie. You can pull the DC cable manager up and outward to lock it into the maintenance position.

Figure 12: MX2008 Standard Cable ManagerMX2008 Standard Cable Manager
Figure 13: Lower Cable ManagerLower Cable Manager

The card-cage cable manager (see Figure 14) is located in the upper card cage, which has rows for routing and securing the cables away from the front of the RCBs and SFBs.

You can use cable strips or other ties to gently secure the cables in the card-cage cable manager. To secure the cables in place, loop the tie through the cable anchor and secure the tie. To access the air filter, the cable manager needs to be opened.

Figure 14: Card-Cage Cable ManagerCard-Cage Cable Manager

Extended Cable Manager

The extended cable manager consists of the following components:

  • Extended lower cable manager—MX2000-CBL-BTM-XT-S

  • Extended DC cable manager—MX2020-DC-CBL-MGR-XT-S

Figure 15: MX2008 Extended Cable ManagerMX2008 Extended Cable Manager
Figure 16: MX2000 Extended Cable Manager for the DC PDM (240 V China) and the Universal (HVAC/HVDC) PDM MX2000 Extended Cable Manager for the DC PDM (240 V China) and the Universal (HVAC/HVDC) PDM

The extended cable manager provides additional support to route and secure a large number of cables away from the front of the MPCs and MICs (see Figure 17).

Figure 17: MX2008 Lower Extended Cable ManagerMX2008 Lower Extended Cable Manager

The extended DC cable manager provides additional support to route and secure a large number of cables away from the rear of the PDMs.

You can use cable strips or other ties to gently secure the cables in the upper and lower extended cable managers. To secure the cables in place, loop the tie through the cable anchor and secure the tie.

MX2008 Rack-Mounting Hardware

The rack-mounting hardware for the MX2008 router includes:

  • One large adjustable mounting shelf for mounting in four-post racks or cabinets

  • Built-in front-mounting flanges on the front of the chassis for front-mounting in a four-post rack or cabinet

  • One open-frame mounting shelf for mounting in an open-frame rack (optional)

  • Two center-mounting brackets for mounting the router in an open-frame rack (optional)

  • Mounting screws

  • Cage-nuts

Note:

There must be a minimum or 24 U of usable rack space when installing the MX2008 router into a rack.