Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Returning an EX3200 Switch or Component for Repair or Replacement

 

Returning an EX3200 Switch or Component for Repair or Replacement

If you need to return a switch or hardware component to Juniper Networks for repair or replacement, follow this procedure:

  1. Determine the serial number of the component. For instructions, see Locating the Serial Number on an EX3200 Switch or Component.
  2. Obtain an RMA number from JTAC as described in Contact Customer Support to Obtain Return Material Authorization.Note

    Do not return any component to Juniper Networks unless you have first obtained an RMA number. Juniper Networks reserves the right to refuse shipments that do not have an RMA. Refused shipments are returned to the customer through collect freight.

  3. Pack the switch or component for shipping as described in Packing an EX3200 Switch or Component for Shipping.

For more information about return and repair policies, see the customer support page at https://www.juniper.net/support/guidelines.html .

Locating the Serial Number on an EX3200 Switch or Component

If you are returning a switch or hardware component to Juniper Networks for repair or replacement, you must locate the serial number of the switch or component. You must provide the serial number to the Juniper Networks Technical Assistance Center (JTAC) when you contact them to obtain Return Materials Authorization (RMA).

If the switch is operational and you can access the CLI, you can list serial numbers for the switch and for some components with a CLI command. If you do not have access to the CLI or if the serial number for the component does not appear in the command output, you can locate the serial number ID label on the physical switch or component (see Figure 1).

Note

If you want to find the serial number on the physical switch component, you will need to remove the component from the switch chassis, for which you must have the required parts and tools available.

Listing the Switch and Components Details with the CLI

To list the switch and switch components and their serial numbers, enter the following CLI command:

Locating the Chassis Serial Number ID Label on an EX3200 Switch

EX3200 switches have serial number ID labels located on the rear panel of the chassis (see Figure 1 ).

Figure 1: Location of the Serial Number ID Label on an EX3200 Switch
Location of the
Serial Number ID Label on an EX3200 Switch

Locating the Serial Number ID Labels on FRUs in an EX3200 Switch

The power supplies, fan trays, and uplink modules installed in EX Series switches are field-replaceable units (FRUs).

For each of these FRUs, you must remove the FRU from the switch chassis to see the FRU’s serial number ID label.

Contact Customer Support to Obtain Return Material Authorization

If you are returning a device or hardware component to Juniper Networks for repair or replacement, obtain a Return Material Authorization (RMA) number from Juniper Networks Technical Assistance Center (JTAC).

After locating the serial number of the device or hardware component you want to return, open a service request with Juniper Networks Technical Assistance Center (JTAC) on the Web or by telephone.

Before you request an RMA number from JTAC, be prepared to provide the following information:

  • Your existing service request number, if you have one

  • Serial number of the component

  • Your name, organization name, telephone number, fax number, and shipping address

  • Details of the failure or problem

  • Type of activity being performed on the device when the problem occurred

  • Configuration data displayed by one or more show commands

You can contact JTAC 24 hours a day, seven days a week on the Web or by telephone:

Note

For international or direct-dial options in countries without toll free numbers, see https://support.juniper.net/support

If you are contacting JTAC by telephone, enter your 12-digit service request number followed by the pound (#) key for an existing case, or press the star (*) key to be routed to the next available support engineer.

The support representative validates your request and issues an RMA number for return of the component.

Packing an EX3200 Switch or Component for Shipping

If you are returning an EX3200 switch or component to Juniper Networks for repair or replacement, pack the item as described in this topic.

Before you begin packing the switch or component:

Ensure that you have the following parts and tools available:

  • Antistatic bag, one for each switch or component

  • Phillips (+) screwdriver, number 2

Packing an EX3200 Switch for Shipping

To pack a switch for shipping:

  1. On the console or other management device connected to the switch, enter the CLI operational mode and issue the following command to shut down the switch software:
    user@switch> request system halt

    Wait until a message appears on the console confirming that the operating system has halted.

  2. Disconnect power from the switch by performing one of the following:
    • If the power source outlet has a power switch, set it to the OFF (0) position.

    • If the power source outlet does not have a power switch, gently pull out the plug end of the power cord connected to the power source outlet.

  3. Remove the cables that connect the switch to all external devices. See Disconnect a Fiber-Optic Cable.
  4. Remove all field-replaceable units (FRUs) from the switch.
  5. If the switch is installed on a wall, rack, or cabinet, have one person support the weight of the switch while another person unscrews and removes the mounting screws.
  6. Remove the switch from the wall, rack, cabinet, or desk and place the switch in an antistatic bag.
  7. Place the switch in the shipping carton.
  8. Place the packing foam on top of and around the switch.
  9. If you are returning accessories or FRUs with the switch, pack them as instructed in the following section.
  10. Replace the accessory box on top of the packing foam.
  11. Close the top of the cardboard shipping box and seal it with packing tape.
  12. Write the RMA number on the exterior of the box to ensure proper tracking.

Packing EX3200 Switch Components for Shipping

Caution

Do not stack switch components. Return individual components in separate boxes if they do not fit together on one level in the shipping box.

To pack and ship switch components:

  • Place individual boards in antistatic bags.

  • Ensure that the components are adequately protected with packing materials and packed so that the pieces are prevented from moving around inside the carton.

  • Close the top of the cardboard shipping box and seal it with packing tape.

  • Write the RMA number on the exterior of the box to ensure proper tracking.