Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

EX2200 Chassis

 

Chassis Status LEDs in EX2200 Switches

The front panel of an EX2200 switch has two chassis status LEDs labeled SYS and ALM on the far right side of the panel. See Figure 1 and Figure 2.

Figure 1: Chassis Status LEDs in an EX2200 Switch Except the EX2200-C Switch
Chassis Status
LEDs in an EX2200 Switch Except the EX2200-C Switch
Figure 2: Chassis Status LEDs in an EX2200-C Switch
Chassis Status
LEDs in an EX2200-C Switch

Table 1 describes the chassis status LEDs in an EX2200 switch, their colors and states, and the status they indicate.

Table 1: Chassis Status LEDs in an EX2200 Switch

LED Label

Color

State and Description

SYS

Green

  • On steadily—The switch is functioning normally.

  • Blinking—The switch is booting.

  • Off—The switch is powered off or is halted.

ALM

Unlit

There is no alarm or the switch is halted.

Amber

There is a minor alarm.

Red

There is a major alarm.

A major alarm (red) indicates a critical error condition that requires immediate action.

A minor alarm (amber) indicates a noncritical condition that requires monitoring or maintenance. A minor alarm that is left unchecked might cause interruption in service or performance degradation.

Both LEDs can be lit simultaneously.

You can view the colors of the two LEDs remotely through the CLI by issuing the operational mode command show chassis led.

Management Port LEDs in EX2200 Switches

The management port on an EX2200 switch has two LEDs that indicate link/activity and port status. The EX2200 switches except the EX2200-C switch models have the management port on the rear panel and the EX2200-C switch has the management port on the front panel. See Figure 3 and Figure 4.

Figure 3: LEDs on the Management Port on an EX2200 Switch Except the EX2200-C Switch Model
LEDs on the Management
Port on an EX2200 Switch Except the EX2200-C Switch Model
Figure 4: LEDs on the Management Port on an EX2200-C Switch
LEDs on the Management
Port on an EX2200-C Switch

Table 2 describes the Link/Activity LED.

Table 2: Link/Activity LED on the Management Port on EX2200 Switches

LED

Color

State and Description

Link/Activity

Green

  • Blinking—The port and the link are active, and there is link activity.

  • On steadily—The port and the link are active, but there is no link activity.

  • Off—The port is not active.

Table 3 describes the Status LED.

Table 3: Status LED on the Management Port on EX2200 Switches

LED

Color

State and Description

Status

Green

Indicates the speed. The speed indicators are:

  • One blink per second—10 Mbps

  • Two blinks per second—100 Mbps

Each network port and uplink port on the front panel of an EX2200 switch has two LEDs that indicate link/activity and port status. Each dual-purpose uplink port in an EX2200-C switch has two pairs of LEDs that indicate the link/activity status, one pair for each of the two ports that constitute the dual-purpose uplink port. See Figure 5, Figure 6, and Figure 7.

Figure 5: LEDs on the Network Port
LEDs on the Network Port

Table 4 describes the Link/Activity LED.

LED

Color

State and Description

Link/Activity

Green

  • Blinking—The port and the link are active, and there is link activity.

  • On steadily—The port and the link are active, but there is no link activity.

  • Off—The port is not active.

In Figure 5, Figure 6, and Figure 7 show the LEDs that indicate the status of one of the four port parameters—speed, duplex mode, administrative status, and Power over Ethernet (PoE) status. Use the Factory reset/Mode button below the LED labeled POE on the far right side of the front panel to toggle the Status LED to show the different port parameters. You can tell which port parameter is indicated by the Status LED by looking at which port status mode LED (SPD, DX, EN, and POE) is lit. (See Figure 6).

Table 5 describes the Status LED.

Table 5: Status LED on the Network Ports, Uplink Ports, and Dual-Purpose Uplink Ports in EX2200 Switches

Port Parameters

State and Description

Speed

Indicates the speed. The speed indicators for network ports are:

  • One blink per second—10 Mbps

  • Two blinks per second—100 Mbps

  • Three blinks per second—1000 Mbps

The speed indicators for uplink ports are:

  • On steadily—1000 Mbps

  • Off—10/100 Mbps

The speed indicators for dual-purpose uplink ports of EX2200-C switch model are:

  • One blink per second—10 Mbps

  • Two blinks per second—100 Mbps

  • Three blinks per second—1000 Mbps

Duplex mode

Indicates the duplex mode. The status indicators are:

  • On steadily—Port is set to full-duplex mode.

  • Off—Port is set to half-duplex mode.

Administrative status

Indicates the administrative status. The status indicators are:

  • On steadily—Port is administratively enabled.

  • Off—Port is administratively disabled.

PoE status

Indicates the PoE status. The status indicators for network ports are:

  • On steadily—PoE is available on the port, a device that draws power from the port is connected to the port, and the device is drawing power from the port.

  • Blinking—PoE is available on the port, but no power is drawn from the port because of one of the following:

    • No device that draws power from the port is connected to the port.

    • A device that draws power from the port is connected to the port, but the device is not drawing any power from the port.

  • Off—PoE is not available on the port.

Note: PoE Status LED is available on the following EX2200 switch models:

  • EX2200-C-12P

  • EX2200-24P

  • EX2200-48P

PoE is not available on uplink ports; therefore, the LED for those ports is always unlit.

You can tell which port parameter is indicated by the Status LED on network ports, uplink ports, and dual-purpose uplink ports by issuing the operational mode command show chassis led.