Rolling Back the Integration of a T640 Router
Problem:
Description: To return the T640 router to its original state as a standalone system after you have transferred control to the TX Matrix router, you can roll back the integration. During the rollback, traffic passing through the router will be interrupted. This procedure uses LCC0 as an example.
Solution
Do not look directly into a fiber-optic array adapter or a connector at the end of a fiber-optic array cable attached to an adapter. The fiber optics emit laser light that can damage your eyes.
To roll back the integration:
- Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
- Take each T640-SIB offline by using one of the following
methods:
Press and hold the
ONLINE/OFFLINE
button on the T640-SIB faceplate until theOK
LED is not lit.On an external management device connected to the console or auxiliary port of the TX-CIP, issue the request chassis sib offline command:
user@host> request chassis sib lcc 0 slot 0 offline
- If the online-expected statement is included
at the [edit chassis lcc number] hierarchy level, delete it:
user@host# delete chassis lcc 0 online-expected
- Issue the commit synchronize command, and ensure
that there are no synchronization errors:
user@host# commit synchronize
- Take the T640 router offline:
user@host> request chassis lcc slot 0 offline
- Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
- Remove the control plane connections between the TX-CIPs
and the T640 LCC Control Boards:
- Disconnect the Ethernet cable plugged into the port labeled
LCC0
on TX-CIP in slotCIP0
. - Disconnect the other end of the Ethernet cable plugged
into the port labeled
CIP
orTX
from theT640 LCCCB0
. - Disconnect the Ethernet cable plugged into the port labeled
LCC0
on the TX-CIP in slotCIP1
. - Disconnect the other end of the Ethernet cable plugged
into the port labeled
CIP
orTX
from theT640 LCC CB1.
- Disconnect the Ethernet cable plugged into the port labeled
- Remove the fiber-optic array cable connector from each T640-SIB adapter. Partially loosen the thumbscrew and captive screw on the fiber-optic array cable connector. (Use the supplied small slotted screwdriver to loosen the captive screw.) Alternate between the thumbscrew and captive screw until the cable connector is removed from the adapter.
- Remove the dust covers from the dust-free resealable plastic bag and reinstall them on the fiber-optic array cable connectors. Align the dust cover with the cable connector and carefully press them together until they stop. The cover and the cable connector are keyed to ensure proper mating. Secure the dust cover by tightening the thumbscrew and captive screw on the connector. (Use the supplied small slotted screwdriver to tighten the captive screw.)
- Dress the fiber-optic array cables so that they are not touching or blocking access to T640 router components, and that they do not drape where people could trip on them.
- Replace each T640-SIB with a SIB. Use the standard replacement
procedure described in the T640 Core Router Hardware Guide.
Do not bring any of the SIBs online.
Note Ensure that the ejector handle tabs are properly mated inside their corresponding chassis slots before you tighten the captive screws on the ejector handles. You might have to close and open the handles a few times before the tabs catch the slots.
- Set the
M/S
switch on each Control Board faceplate toS
. - Set the
CHASSIS ID
switch on each Control Board faceplate to0
. - On an external management device connected to the console
or auxiliary port of the T640-CIP, load the original T640 router configuration.
For example:
user@host# load override t640-config.conf
- If graceful switchover is enabled in the original T640
router configuration, disable it as follows:
user@host# delete chassis redundancy graceful-switchover
- Issue the commit synchronize command and ensure
that there are no synchronization errors:
user@host# commit synchronize
- On an external management device connected to the console
or auxiliary port of T640-CIP-0, reboot the corresponding Routing
Engine in the T640 router:
user@host> request system reboot
- On an external management device connected to the console
or auxiliary port of T640-CIP-1, reboot the corresponding Routing
Engine in the T640 router:
user@host> request system reboot
- Display the status of the SIBs by issuing the show
chassis sibs command on the master Routing Engine:
user@host> show chassis sibs
Slot State Uptime 0 Spare 255 days, 31 minutes, 12 seconds 1 Online 255 days, 31 minutes, 12 seconds 2 Online 255 days, 31 minutes, 12 seconds 3 Online 255 days, 31 minutes, 12 seconds 4 Online 255 days, 31 minutes, 12 seconds
Verify that four SIBs are in the Online state and one SIB is in the Spare state.
- Delete all statements associated with LCC0 from the TX Matrix router configuration. To review the T640 router configuration changes that were merged into the TX Matrix router configuration, see Creating a Configuration File on the T640 Router for Integration into the Routing Matrix.
You do not need to replace the rear fan tray with the original one.