Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 

Rolling Back the Integration of a T4000 Line-Card Chassis with TXP-LCC-3D SIBs

 

After you have transferred control to the TX Matrix Plus router, you can roll back the integration to return a T4000 router with TXP-LCC-3D SIBs to its original state as a standalone system . During the rollback, traffic passing through the router will be interrupted. This procedure uses LCC0 as an example.

  1. Preparing to Roll Back the Integration

  2. Removing the Control Plane Connections

  3. Removing the Switching Planes

  4. Returning to the Original T4000 Configuration

Preparing to Roll Back the Integration

  1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
  2. Take each TXP-LCC-3D SIB offline, using one of the following methods.
    • Press and hold the ONLINE/OFFLINE button on the TXP-LCC-3D SIB faceplate until the OK LED is not lit.

    • On an external management device connected to the console or auxiliary port of the TXP-CB, issue the request chassis sib offline command:

      user@host> request chassis sib lcc 0 slot 0 offline
  3. If the online-expected statement is included at the [edit chassis lcc number] hierarchy level, delete it:
    user@host# delete chassis lcc 0 online-expected
  4. Issue the commit synchronize command and ensure that there are no synchronization errors:
    user@host# commit synchronize
  5. Take the T4000 router offline:
    user@host> request chassis lcc slot 0 offline

Removing the Control Plane Connections

To remove the control plane connections between the TXP-CIPs and the LCC-CBs:

  1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
  2. Disconnect the Ethernet cable plugged into the LCC control plane port labeled 0 on the TXP-CIP in slot CIP0 in the TX Matrix Plus router.
  3. Disconnect the other end of the Ethernet cable plugged into the port labeled SFC0 on the LCC-CB in slot CB0 in the T4000 router.
  4. Disconnect the Ethernet cable plugged into the LCC control plane port labeled LCC0 on the TXP-CIP in slot CIP1 in the TX Matrix Plus router.
  5. Disconnect the other end of the Ethernet cable plugged into the port labeled SFC0 on the LCC-CB in slot CB1 in the T4000 router.
Note

LCC-CBs are supported in standalone T40000 routers. It is not necessary to remove the LCC-CBs from the T4000 routers.

Removing the Switching Planes

To remove the switching planes:

  1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
  2. Remove the switching plane cables from each TXP-LCC3D SIB.
  3. For CXP cables, remove the dust covers from the dust-free resealable plastic bag and reinstall them on the cable connectors. Align the dust cover with the cable connector and carefully press them together until they stop. The cover and the cable connector are keyed to ensure proper mating.
  4. Arrange the switching plane cables so that they are not touching or blocking access to T4000 router components, and that they do not drape where people could trip on them.
  5. Replace each TXP-LCC-3D SIB with a T4000-SIB. Use the standard replacement procedure described in the T4000 Core Router Hardware Guide.

    Do not bring any of the SIBs online.

    Note

    Ensure that the ejector handle tabs are properly mated inside their corresponding chassis slots before you tighten the captive screws on the ejector handles. You might have to close and open the handles a few times before the tabs catch the slots.

Returning to the Original T4000 Configuration

To return to the original T4000 configuration:

  1. Set the M/S switch on each LCC-CB on the T4000 router faceplate to S.
  2. On an external management device connected to the console or auxiliary port of the T4000 CIP, load the original T4000 router configuration. For example:
    user@host# load override t4000-config.conf
  3. If graceful switchover is enabled in the original T4000 router configuration, disable it as follows:
    user@host# delete chassis redundancy graceful-switchover
  4. Issue the commit synchronize command and ensure that there are no synchronization errors:
    user@host# commit synchronize
  5. On an external management device connected to the HOST 0CONSOLE or AUXILIARY port on the T4000 CIP, reboot the corresponding Routing Engine in the T4000 router:
    user@host> request system reboot
  6. On an external management device connected to the HOST 1 CONSOLE or AUXILIARY port on the T4000 CIP, reboot the corresponding Routing Engine in the T4000 router:
    user@host> request system reboot
  7. Display the status of the SIBs by issuing the show chassis sibs command on the master Routing Engine:
    user@host> show chassis sibs

    Verify that four SIBs are in the Online state and one SIB is in the Spare state.

  8. Delete all statements associated with LCC0 from the TX Matrix Plus router configuration. To review the T4000 router configuration changes that were merged into the TX Matrix Plus router configuration. .