Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    Replacing a JCS1200 SFP

    Removing a JCS1200 SFP

    Small form-factor pluggables (SFPs) are transceivers that can be removed from a fiber Gigabit Ethernet switch module. SFPs are hot-insertable and hot-removable. Removing an SFP does not interrupt switch module functioning, but the removed SFP no longer receives or transmits data.

    Figure 1: Small Form-Factor Pluggable (SFP)

    Small Form-Factor Pluggable (SFP)

    To remove an SFP (see Figure 1):

    1. Place an electrostatic bag or antistatic mat on a flat, stable surface to receive the SFP. Have ready a rubber safety cap for the SFP transceiver and the cable.
    2. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
    3. Label the cable connected to the SFP so that you can later reconnect it to the correct SFP.
    4. Disconnect the cable from the SFP. Immediately cover the transceiver and the end of the cable with a rubber safety cap.

      Warning: Do not look directly into a fiber-optic transceiver or into the ends of fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a transceiver emit laser light that can damage your eyes.

      Caution: Do not leave a fiber-optic transceiver uncovered except when you are inserting or removing cable. The safety cap keeps the port clean and prevents accidental exposure to laser light.

    5. Arrange the cable in the cable management system to prevent it from dislodging or developing stress points. Secure the cable so that it is not supporting its own weight as it hangs to the floor. Place excess cable out of the way in a neatly coiled loop in the cable management system. Placing fasteners on the loop helps to maintain its shape.

      Caution: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc smaller than a few inches in diameter can damage the cable and cause problems that are difficult to diagnose.

    6. Pull the ejector handle away from the SFP faceplate to unseat the SFP from the switch module. Pull the SFP out of the switch module and place it on the antistatic mat or in the electrostatic bag.

    Caution: After removing a transceiver from the chassis, wait at least 30 seconds before reinserting it or inserting a transceiver into a different slot.

    Installing a JCS1200 SFP

    To install a replacement SFP:

    1. Attach an electrostatic discharge (ESD) grounding strap to your bare wrist, and connect the strap to one of the ESD points on the chassis.
    2. Verify that a rubber safety cap covers the SFP transceiver, installing one if necessary.
    3. Orient the SFP over the port in the switch module so that the connector end will enter the slot first and the SFP connector faces the appropriate direction:
    4. Slide the SFP into the slot. If there is resistance, remove the SFP and flip it so that the connector faces the other direction.
    5. Remove the rubber safety cap from the transceiver and the end of the cable, and insert the cable into the transceiver.

      Warning: Do not look directly into a fiber-optic transceiver or into the ends of fiber-optic cables. Fiber-optic transceivers and fiber-optic cable connected to a transceiver emit laser light that can damage your eyes.

      Caution: Do not leave a fiber-optic transceiver uncovered except when you are inserting or removing cable. The safety cap keeps the port clean and prevents accidental exposure to laser light.

    6. Arrange the cable in the cable management system to prevent the cable from dislodging or developing stress points. Secure the cable so that it is not supporting its own weight as it hangs to the floor. Place excess cable out of the way in a neatly coiled loop in the cable management system. Placing fasteners on the loop helps to maintain its shape.

      Caution: Do not let fiber-optic cable hang free from the connector. Do not allow fastened loops of cable to dangle, which stresses the cable at the fastening point.

      Caution: Avoid bending fiber-optic cable beyond its minimum bend radius. An arc smaller than a few inches in diameter can damage the cable and cause problems that are difficult to diagnose.

    7. Verify that the status LEDs on the switch module faceplate indicate that the SFP is functioning correctly (there is an LED for each SFP port).

    Published: 2013-01-30