Technical Documentation

SRX210 Services Gateway Installation

You can install the SRX210 Services Gateway in a rack, on a desk, or on a wall. The device includes rubber feet for desk and wall mounting. The mounting brackets are optional accessories.

Install the device as appropriate for your site using one of the following procedures:

Installing the SRX210 Services Gateway in a Rack

You can front-mount the SRX210 Services Gateway in a rack. Many types of racks are acceptable, including four-post (telco) racks, enclosed cabinets, and open-frame racks. For more information about the type of rack or cabinet the SRX210 Services Gateway can be installed into, see SRX210 Services Gateway Rack Requirements.

Note: The rack-mounting kit is not shipped with the device and must be ordered separately.

  • If you are installing multiple devices in one rack, install the lowest one first and proceed upward in the rack.
  • Make sure that the rubber feet from the base of the chassis are removed for rack installation.


To install the device in a rack:

  1. Position a mounting bracket on each side of the chassis as shown in Figure 1.

    Figure 1: Installation of SRX210 Services Gateway in a Rack — Positioning Mounting Brackets

    Image g031126.gif

    Table 1 lists the parts used for installing the SRX210 Services Gateway on the rack. The numbers in Figure 1 correspond to the numbers in Table 1.

    Table 1: SRX210 Services Gateway Rack Installation Parts

    S.No

    Part

    1

    Mounting brackets

    2

    Screws (Mounting bracket)

    3

    Power supply adapter tray

    4

    Screws (Power supply adapter tray)

  2. Use a number-1 Phillips screwdriver to install the screws that secure the mounting brackets and power supply adapter tray to the chassis as shown in Figure 2.

    Figure 2: SRX210 Services Gateway Rack Installation — Securing Mounting Brackets and Power Supply Adapter Tray

    Image g031127.gif

  3. Place the power supply adapter in the tray as shown in Figure 3

    Figure 3: SRX210 Services Gateway Rack Installation — Positioning Power Supply Adapter Tray

    Image g031128.gif

  4. Have one person grasp the sides of the device, lift it, and position it in the rack.
  5. Align the bottom hole in each mounting bracket with a hole in each rack rail as shown in Figure 4, making sure the chassis is level.

    Figure 4: SRX210 Services Gateway Rack Installation — Hanging the Services Gateway in a Rack

    Image g031129.gif

  6. Have a second person install a mounting screw into each of the two aligned holes. Use a number-1 Phillips screwdriver to tighten the screws.
  7. Install the second screw in each mounting bracket.
  8. Verify that the mounting screws on one side of the rack are aligned with the mounting screws on the opposite side and that the device is level.

Installing the SRX210 Services Gateway on a Desk

Follow these guidelines when installing the device on a desk:

  • You can install the SRX210 Services Gateway on a desk, table, or other level surface.
  • The device is shipped with the rubber feet attached. The rubber feet are necessary to stabilize the device on the desk.
  • You can install the device in a horizontal or vertical position.
  • The vertical position requires the vertical installation kit, which consists of a vertical installation stand with the rubber feet attached.

    Note: The desk-mounting kit is not shipped with the device and must be ordered separately.

To install the device in a horizontal position:

The horizontal position is the standard installation position and does not require the vertical installation kit.

  1. Make sure that the rubber feet are attached to the chassis.
  2. Place the device on a desk with the Juniper Networks logo embossed on the top cover facing up.

To install the device in a vertical position:

  1. Place the device on a flat and level surface with the Juniper Networks logo embossed on the top cover facing up.
  2. Attach the vertical stand to the right side of the chassis using the specified screws as shown in Figure 5.

    Figure 5: SRX210 Services Gateway Desk Installation — Attaching Vertical Stand

    Image g031124.gif

  3. Place the chassis vertically on the desk with the stand resting on the desk as shown in Figure 6.

    Figure 6: SRX210 Services Gateway Desk Installation — Placing the Services Gateway on Desk

    Image g031125.gif

Installing the SRX210 Services Gateway on a Wall

You can install the SRX210 Services Gateway on a wall.

Note: The wall-mounting kit is not shipped with the device and must be ordered separately.

To install the device on a wall:

  1. Place the device on a flat and level surface with Juniper Networks Logo embossed on the top cover facing up. Ensure that rubber feet are attached to the bottom of the chassis.
  2. Position a mounting bracket on each side of the chassis as shown in Figure 7.

    Figure 7: SRX210 Services Gateway Wall Installation — Attaching Mounting Brackets

    Image g031130.gif

    Table 2 lists the parts used for installing the SRX210 Services Gateway on the wall. The numbers in Figure 7 correspond to the numbers in Table 2.

    Table 2: SRX210 Services Gateway Wall Installation Parts

    Numbers

    Part

    1

    Mounting brackets

    2

    Screws (Mounting bracket)

  3. Use a number-1 Phillips screwdriver to install the screws that secure the mounting brackets to the chassis.
  4. If you are using wall anchors to support the chassis, install two pairs of anchors on the wall, spaced apart equal to width of chassis with mounting brackets attached.
  5. Have one person grasp the sides of the device, lift it, and position it on the wall.
  6. Have a second person install two pairs of mounting screws through the bracket holes on either side of the device to secure it to the wall.
  7. Verify that the mounting screws on one side are aligned with the mounting screws on the opposite side and that the device is level (see Figure 8).

Figure 8: SRX210 Services Gateway Wall Installation — Hanging the Services Gateway on Wall

Image g031131.gif


Published: 2009-10-26