Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

Navigation
Guide That Contains This Content
[+] Expand All
[-] Collapse All

    Powering On the LN1000 Mobile Secure Router

    The LN1000 router derives its power from the chassis in which it is installed; it automatically powers on when inserted into the connector in the VITA 46.0-compliant chassis.

    Monitor router startup on the console and the LED on the front panel of the LN1000 router to verify that the router is booting properly.

    As a standard part of the boot process, the router runs startup power-on self test (SPOST) and then power-on self test (POST) diagnostics. A successful startup looks similar to the following example:

    CPU Memory (Data32: 00000000-0007ffff) test completed, 1 pass, 0 errors 
    CPU Memory (Data32: 0f000000-0fffffff) test completed, 1 pass, 0 errors 
    CPU Memory (Addr32: 00000000-0007ffff) test completed, 1 pass, 0 errors 
    CPU Memory (Addr32: 0f000000-0fffffff) test completed, 1 pass, 0 errors
    
    Boot Flash: 16 MB in 131 Sectors (portwidth: 16bit  chipwidth: 16bit) 
    OCTEON CN56XX pass 2.0, Core clock: 600 MHz, DDR clock: 266 MHz
    
    
    
    Initializing USB
    Device 1:
      Product      DOTG Root Hub
    Device 2:
      Manufacturer         
      Product      USB Flash Memory
      SerialNumber 00147808E485C92043770566
    
    Initializing IDE
    
    Initializing FPGA
    Programming /cf/usr/share/pfe/firmware/563-029572.bit: 2067590 bytes 
    Programmed successfully (time: 883475051 ticks) 
    Checking for init_data 
    No init_data
    PCIe: Waiting for port 0 link
    PCIe: Port 0 link active, 1 lanes
    Probing PCIe port 0
    0:00:00.0 0x003b1304
    PCIe port 0 had 1 busses
    HWA FPGA Version 0x0004090900000013
    PCIe: Waiting for port 1 link
    PCIe: Port 1 link active, 4 lanes
    Probing PCIe port 1
    1:00:00.0 0x0009184e
    PCIe port 1 had 1 busses
    IDP Revision Date-Time: 05/28/08-18:00:00 
    Enumeration took 0 reboots
    
    
    Juniper LN1000-V revision 2.0, Serial# ************ 
    Juniper Part # 710-027379 Bootstrap version 10.0I
    
    Build:       10.0B3.7 #0: 2009-09-25 16:36:56 UTC
                    builder@ormonth.juniper.net
    
    SDRAM:       1024 MB
    Boot flash:  16 MB @ 0x1fc00000
    IDE flash:   977.4 MB (2001888 x 512)
    USB:         1.8 GB (3911616 x 512)
    current_dev: ide
    coremask:    0xfff (12 cores)
    resetmask:   0xffe (1 cores running)
    reset:       Hard
    NVMRO:       Write-enabled
    watchdog:    Armed
    FPGA:        Enabled
    
    Hit any key to stop autoboot: 10
     IPMC test
     IPMC test completed, 1 pass, 0 errors, 0 warnings
    
    BOOT > 
    

    For normal operation, allow the autoboot to proceed. Full POST diagnostics then run, and the system starts Junos OS normally. If detailed diagnostics must be run, or if alternate media (for example, a USB storage device) must be booted, press ENTER during the 10-second count-down. The following bootstrap prompt is displayed:

    BOOT>

    If POST diagnostics or the bootstrap sequence fails, this prompt is redisplayed, and the front panel LED lights red.

    You are now ready to configure and operate the router.

    Published: 2015-04-07