[an error occurred while processing this directive] [an error occurred while processing this directive]

SRX 210 Services Gateway 1-Port SFP Mini-Physical Interface Module Configuration

To use the port on the 1-Port SFP Mini-Physical Interface Module (Mini-PIM), you must assign it to a zone other than the Null zone. Optionally, you can also assign the port an IP address.

To perform basic configuration for a port on the 1-Port SFP Mini-PIM, use the J-Web or CLI as follows:

  1. Select Configuration > Quick Configuration > Interfaces if the Interfaces Quick Configuration page is not displayed.
  2. Enter information into the Interfaces Quick Configuration page, as described in Table 1.
  3. Click one of the following buttons:
    • Click OK to apply the configuration and return to the J-Web Quick Configuration page.
    • Click Cancel to cancel your entries and return to the J-Web Quick Configuration page.

The properties you can configure on a Gigabit Ethernet interface are displayed, as shown in Figure 1.

Figure 1: 1-Port SFP Mini-PIM Quick Configuration Page

Image s031000.gif

Table 1: 1-Port SFP Mini-PIM Quick Configuration Page Summary

Field

Function

Your Action

Logical Interfaces

Add logical interfaces

Defines one or more logical units that you connect to this physical Gigabit Ethernet interface. You must define at least one logical unit for a Gigabit Ethernet interface.

Click Add.

Logical Interface Description

(Optional) Describes the logical interface.

Type a text description of the logical interface to more clearly identify it in monitoring displays.

IPv4 Addresses and Prefixes

Specifies one or more IPv4 addresses for the interface.

  1. Type one or more IPv4 addresses and prefixes. For example:

    10.10.10.10/24

  2. Click Add.
  3. Click OK.

To delete an IP address and prefix, select them in the Source Addresses and Prefixes box, then click Delete.

ARP Address

Enables the device to create a static Address Resolution Protocol (ARP) entry for this interface by specifying the IP address of a node to associate with its media access control (MAC) address. The IP address must be in the same subnet as the IPv4 address or prefix of the interface you are configuring.

Static ARP entries associate the IP addresses and MAC addresses of nodes on the same subnet, enabling a services gateway to respond to ARP requests having destination addresses that are not local to the incoming interface.

Type the IPv4 address that you want to associate with the MAC address—for example, 10.10.10.1.

MAC Address

Specifies the hardware media access control (MAC) address associated with the ARP address.

The MAC address uniquely identifies the system and is expressed in the following format: mm:mm:mm:ss:ss:ss. The first three octets denote the hardware manufacturer ID, and the last three are serial numbers identifying the device.

Type the MAC address to be mapped to the ARP entry—for example, 00:12:1E:A9:8A:80.

Publish

Enables the device to reply to ARP requests for the specified address.

  • To enable publishing, select the box.
  • To disable publishing, clear the box.

Physical Interface Description

(Optional) Adds supplementary information about the physical Gigabit Ethernet interface.

Type a text description of the Gigabit Ethernet interface to more clearly identify it in monitoring displays.

MTU (bytes)

Specifies the maximum transmission unit size for the Gigabit Ethernet interface.

Type a value between 256 and 1518 bytes. The default MTU for Gigabit Ethernet interfaces is 1514.

Per unit scheduler

Enables scheduling on logical interfaces.

Allows you to configure multiple output queues on a logical interface and associate an output scheduler and shaping rate with the queues.

  • To enable scheduling, select the box.
  • To disable scheduling, clear the box.
Gigabit Ethernet Options

Loopback

Enables or disables the loopback option.

Select Yes to enable the loopback diagnostic option, or select No to disable the loopback option. By default, loopback is disabled.

Auto Negotiation

Indicates autonegotiation is enabled.

By default, autonegotiation is enabled.

Auto Negotiation Remote Fault

Indicates the autonegotiation remote fault value.

Select the autonegotation remote fault value from the list of options given. This field is enabled only if autonegotiation is enabled.

Redundant Parent

TBD

TBD

Tag Protocol ID

Displays a list of IEEE 802.1Q Tag Protocol Identifier (TPID) values. The TPIDs identify frames that are to be processed as virtual LAN (VLAN)-tagged frames.

To use this feature, you must already have enabled VLAN tagging. VLAN tags enable you to channelize an Ethernet interface into multiple logical interfaces, allowing many hosts to be connected to the same Gigabit Ethernet switch.

To add a TPID, type it in the boxes above the Add button, then click Add.

To delete a TPID, select it in the box, then click Delete.

Each Gigabit Ethernet port can have up to eight TPIDs.

For more information about TPIDs and VLAN tagging, see the JUNOS Network Interfaces Configuration Guide.

CLI

set interface ge-1/0/0 unit 0 family inet address <ipaddress/mask>

set security zones security-zone zone1 interfaces ge-1/0/0.0 host-inbound-traffic system-services all

set security zones security-zone zone1 interfaces ge-1/0/0.0 host-inbound-traffic protocols all

set security policies default-policy permit-all

[an error occurred while processing this directive]