| Identification
|
|
Host Name (required)
|
Defines the hostname of the switching platform.
|
Type the hostname.
|
|
Domain Name
|
Defines the network or subnetwork that the
machine belongs to.
|
Type the domain name.
|
|
Root Password (required)
|
Sets the root password that user root can use to log in to the switching platform.
|
Type a plain-text password. The system encrypts
the password.
Note:
After a root password has been defined, it is required
when you log in to the J-Web user interface or the CLI.
|
|
Verify Root Password (required)
|
Verifies that the root password has been typed
correctly.
|
Retype the password.
|
| Time
|
|
Time Zone
|
Identifies the time zone that the switching
platform is located in.
|
Select the appropriate time zone from the
list.
|
|
NTP Servers
|
Specifies an NTP server for the switching
platform to use to synchronize the system time.
|
To add an IP address, type it in the box to
the left of the Add button, then click Add.
To delete an IP address, click on it in the box above the Add button, then click Delete.
|
|
Current System Time
|
Synchronizes the system time with the NTP
server. You can also manually set the system time and date.
|
|
| Network
|
|
DNS Name Servers
|
Specifies a DNS server for the switching platform
to use to resolve hostnames into addresses.
|
To add an IP address, type it in the box to
the left of the Add button, then click Add.
To delete an IP address, click on it in the box above the Add button, then click Delete.
|
|
Domain Search
|
Add the names of domains that the switching
platform includes in to the configuration so that they are included
in a DNS search.
|
To add a domain name, type it in the box to
the left of the Add button, then click Add.
To delete a domain name, click on it in the box above the Add button, then click Delete.
|
|
Default Gateway
|
Defines a default gateway through which to
direct packets addressed to networks that are not explicitly listed
in the routing table.
|
Type a 32-bit IP address, in dotted decimal
notation.
|
|
Loopback Address
|
Defines a reserved IP address that is always
available on the switching platform. If no address is entered, this
address is set to 127.0.0.1/32.
|
Type a 32-bit IP address and prefix length,
in dotted decimal notation.
|
|
ge—0/0/0 or fe-0/0/0 Address
|
Defines the IP address and prefix length of ge–0/0/0 or fe-0/0/0. The interface ge–0/0/0 or fe-0/0/0 is typically used as the management interface
for accessing the switching platform. The DHCP client sets this address
to 192.168.1.1/24 if no DHCP server is found.
|
Type a 32-bit IP address and prefix length,
in dotted decimal notation.
Caution:
You must enter the ge–0/0/0 or fe-0/0/0 address on the Quick Configuration Set Up page before you click Apply or OK. If you do not manually
configure this address, you will lose your connection to the J-Web
interface when you click Apply or OK.
|
| Management
Access |
|
Allow Telnet Access
|
Allows remote access to the switching platform
using Telnet.
|
To enable Telnet access, select the check
box.
|
|
Allow JUNOScript over Clear-Text Access
|
Allows JUNOScript to access the switching
platform using a protocol for sending unencrypted text over a TCP
connection.
|
To enable JUNOScript access over clear text,
select the check box.
|
|
Allow SSH Access
|
Allows remote access to the switching platform
using SSH.
|
To enable SSH access, select the check box.
|
