Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 

24-Port Gigabit Ethernet XPIM Components

 

The 24-Port Gigabit Ethernet XPIM contains the components listed in Table 1.

Table 1: 24-Port Gigabit Ethernet XPIM Components

Component

Location

Description

XPIM ONLINE/OFFLINE button

Only the SRX650 Services Gateway supports hot-swappable functionality for GPIMs. The SRX550 Services Gateway does not support hot-swappable functionality for GPIMs.

Right side of the XPIM

Use the XPIM ONLINE/OFFLINE button to gracefully shut down the XPIM.

24 fixed Gigabit Ethernet ports labeled 0–23

Note: The 24-Port Gigabit Ethernet with PoE XPIM port labels are yellow instead of white.

Note: The RJ-45 and SFP ports 20–23 are shared ports. The SFP port will always take priority over the corresponding RJ-45 port if they are both connected.

Middle of the XPIM

Note: Each port on the 24-Port Gigabit Ethernet with PoE XPIM supports Power over Ethernet (PoE).

Each Gigabit Ethernet port:

  • Provides link speeds of 10/100/1000 Mbps

  • Uses an RJ-45 connector

  • Operates in full-duplex and half-duplex modes

  • Supports flow control

  • Supports autonegotiation

4 1-Gigabit small form-factor pluggable (SFP) ports labeled 20–23

See Table 2 for supported SFP transceivers.

Note: The RJ-45 and SFP ports 20–23 are shared ports. The SFP port will always take priority over the corresponding RJ-45 port if they are both connected.

Right side of the RJ-45 ports 0–23

Use these ports to connect various SFP transceivers for fiber cable connections.

Captive screws

One on each side of the XPIM

Use the captive screws to hold the XPIM in place.

Handles

One on each side of the XPIM

Use the handles to grasp the XPIM for installation or removal.

You can customize the Ethernet interface type by using different SFP transceivers. Table 2 shows the available SFP transceivers.

Caution

If you face a problem running a Juniper Networks device that uses a third-party optic or cable, the Juniper Networks Technical Assistance Center (JTAC) can help you diagnose the source of the problem. Your JTAC engineer might recommend that you check the third-party optic or cable and potentially replace it with an equivalent Juniper Networks optic or cable that is qualified for the device.

Table 2: 24-Port Gigabit Ethernet XPIM SFP Transceivers

Product Number

Interface Type

Connector

JX-SFP-FE-FX

100Base-FX Fast Ethernet optical transceiver SFP

LC

JX-SFP-1GE-LH

1000Base-LH Gigabit Ethernet optical transceiver SFP, 80 Km reach

LC

JX-SFP-1GE-LX

1000Base-LX Gigabit Ethernet optical transceiver SFP

LC

JX-SFP-1GE-SX

1000Base-SX Gigabit Ethernet optical transceiver SFP, 550 m reach without DDM (Difference in the Depth of Modulation)

LC

JX-SFP-1GE-T

1000Base-T Gigabit Ethernet copper transceiver SFP

RJ-45

SRX-SFP-1GE-LH

1000Base-LH Gigabit Ethernet optical transceiver SFP

LC

SRX-SFP-1GE-LX

1000Base-LX Gigabit Ethernet optical transceiver SFP

LC

SRX-SFP-1GE-SX

1000Base-SX Gigabit Ethernet optical transceiver SFP

LC

SRX-SFP-1GE-T

1000Base-T Gigabit Ethernet optical transceiver SFP

Cat 5 cable

SRX-SFP-FE-FX

100Base-FX Fast Ethernet optical transceiver SFP

LC