Help us improve your experience.

Let us know what you think.

Do you have time for a two-minute survey?

 

2-Port 10-Gigabit Ethernet XPIM Components

 

The 2-Port 10 Gigabit Ethernet XPIM contains the components listed in Table 1.

Table 1: 2-Port 10 Gigabit Ethernet XPIM Components

Component

Location

Description

XPIM ONLINE/OFFLINE button

Only the SRX650 Services Gateway supports hot-swappable functionality for GPIMs. The SRX550 Services Gateway does not support hot-swappable functionality for GPIMs.

Right side of the XPIM

Use the XPIM ONLINE/OFFLINE button to gracefully shut down the XPIM.

Two groups of ports labeled 0 and 1, where each group contains 1 copper port and 1 fiber port.

Note: By default, all ports are flow control enabled, and support link speed of 10 G in full-duplex mode.

The 10 G fiber port does not support autonegotiation.

Use the fiber ports to connect various SFP+ transceivers for fiber cable connections. See Table 2 for supported SFP+ transceivers.

Middle of the XPIM

  • Copper ports support link speeds of 10/100/1000 Mbps/10 G in full-duplex and half-duplex modes.

  • Fiber ports support link speeds of 1000 Mbps/10 G in full-duplex mode.

    Note: The 1 G fiber port configuration is supported starting with Junos OS Release 10.2R2.

  • Copper ports (for 10 G) use a CAT-6a or CAT-7 cable connector.

  • Copper ports support autonegotiation; whereas fiber ports do not support autonegotiation.

    Note: The 10 G fiber port does not support autonegotiation.

  • All ports support flow control and can be configured in loopback mode for testing purposes.

Captive screws

One on each side of the XPIM

Use the captive screws to hold the XPIM in place.

You can customize the Ethernet interface type by using different SFP+ transceivers. Table 2 shows the available SFP+ transceivers.

Caution

If you face a problem running a Juniper Networks device that uses a third-party optic or cable, the Juniper Networks Technical Assistance Center (JTAC) can help you diagnose the source of the problem. Your JTAC engineer might recommend that you check the third-party optic or cable and potentially replace it with an equivalent Juniper Networks optic or cable that is qualified for the device.

Table 2: 2-Port 10- Gigabit Ethernet XPIM SFP+ Transceivers

Product Number

Interface Type

Media

Connector

SFPP-10GE-SR

10GBase-SR Ethernet optical transceiver SFP, 26 m reach

MMF

LC

SFPP-10GE-LR

10GBase-LR Ethernet optical transceiver SFP, 10 Km reach

SMF

LC

SFPP-10GE-ER

10GBase-ER Ethernet optical transceiver SFP, 40 Km reach

SMF

LC

SFPP-10GE-LRM

10GBase-LRM Ethernet optical transceiver SFP, 220 m reach

MMF

LC

Copper Twin-AX 1m

10GE Ethernet cable assembly plugs into SFP+ socket, 15 m reach

Direct Attached 30 AWG

Cable connector with 1 m cable length

Copper Twin-AX 3m

10GE Ethernet cable assembly plugs into SFP+ socket, 15 m reach

Direct Attached 30 AWG

Cable connector with 3 m cable length

Copper Twin-AX 5m

10GE Ethernet cable assembly plugs into SFP+ socket, 15 m reach

Direct Attached 24 AWG

Cable connector with 5 m cable length

Copper Twin-AX 7m

10GE Ethernet cable assembly plugs into SFP+ socket, 15 m reach

Direct Attached 24 AWG

Cable connector with 7 m cable length

Related Documentation